BSS138LT1 Preferred Device Power MOSFET 200 mAmps, 50 Volts N-Channel SOT-23 Typical applications are dc-dc converters, power management in portable and battery-powered products such as computers, printers, PCMCIA cards, cellular and cordless telephones. * Low Threshold Voltage (VGS(th): 0.5V...1.5V) makes it ideal for low voltage applications * Miniature SOT-23 Surface Mount Package saves board space http://onsemi.com 200 mAMPS 50 VOLTS RDS(on) = 3.5 MAXIMUM RATINGS (TA = 25C unless otherwise noted) Symbol Value Unit VDSS 50 Vdc Gate-to-Source Voltage - Continuous VGS 20 Vdc Drain Current - Continuous @ TA = 25C - Pulsed Drain Current (tp 10 s) ID IDM 200 800 Total Power Dissipation @ TA = 25C PD 225 mW Operating and Storage Temperature Range TJ, Tstg - 55 to 150 C RJA 556 C/W TL 260 C Rating Drain-to-Source Voltage Thermal Resistance - Junction-to-Ambient Maximum Lead Temperature for Soldering Purposes, for 10 seconds N-Channel 3 mA 1 2 MARKING DIAGRAM 3 SOT-23 CASE 318 STYLE 21 1 J1 W 2 W = Work Week PIN ASSIGNMENT Drain 3 1 2 Source Gate ORDERING INFORMATION Device Package Shipping BSS138LT1 SOT-23 3000 Tape & Reel BSS138LT3 SOT-23 10,000 Tape & Reel Preferred devices are recommended choices for future use and best overall value. Semiconductor Components Industries, LLC, 2000 November, 2000 - Rev. 2 1 Publication Order Number: BSS138LT1/D BSS138LT1 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit V(BR)DSS 50 - - Vdc - - - - 0.1 0.5 OFF CHARACTERISTICS Drain-to-Source Breakdown Voltage (VGS = 0 Vdc, ID = 250 Adc) Adc Zero Gate Voltage Drain Current (VDS = 25 Vdc, VGS = 0 Vdc) (VDS = 50 Vdc, VGS = 0 Vdc) IDSS Gate-Source Leakage Current (VGS = 20 Vdc, VDS = 0 Vdc) IGSS - - 0.1 Adc Gate-Source Threshold Voltage (VDS = VGS, ID = 1.0 mAdc) VGS(th) 0.5 - 1.5 Vdc Static Drain-to-Source On-Resistance (VGS = 2.75 Vdc, ID < 200 mAdc, TA = -40C to +85C) (VGS = 5.0 Vdc, ID = 200 mAdc) rDS(on) - - 5.6 - 10 3.5 gfs 100 - - mmhos (VDS = 25 Vdc, VGS = 0, f = 1 MHz) Ciss - 40 50 pF Output Capacitance (VDS = 25 Vdc, VGS = 0, f = 1 MHz) Coss - 12 25 Transfer Capacitance (VDG = 25 Vdc, VGS = 0, f = 1 MHz) Crss - 3.5 5.0 td(on) - - 20 td(off) - - 20 ON CHARACTERISTICS (Note 1.) Forward Transconductance (VDS = 25 Vdc, ID = 200 mAdc, f = 1.0 kHz) Ohms DYNAMIC CHARACTERISTICS Input Capacitance SWITCHING CHARACTERISTICS (Note 2.) Turn-On Delay Time Turn-Off Delay Time (VDD = 30 Vdc, Vdc ID = 0.2 0 2 Adc,) Adc ) 1. Pulse Test: Pulse Width 300 s, Duty Cycle 2%. 2. Switching characteristics are independent of operating junction temperature. http://onsemi.com 2 ns BSS138LT1 TYPICAL ELECTRICAL CHARACTERISTICS 0.7 0.9 VGS = 3.5 V TJ = 25C VGS = 3.25 V 0.6 VGS = 3.0 V 0.5 VGS = 2.75 V 0.4 VGS = 2.5 V 0.3 0.2 0.1 0 VDS = 10 V 0.8 I D , DRAIN CURRENT (AMPS) I D , DRAIN CURRENT (AMPS) 0.8 -55C 0.7 150C 0.6 0.5 0.4 0.3 0.2 0.1 0 1 2 3 4 5 6 7 8 9 0 10 0 0.5 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) 1 1.5 2 2.5 3 3.5 4 4.5 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) Figure 2. Transfer Characteristics Figure 1. On-Region Characteristics 2.2 1.25 ID = 1.0 mA 2 Vgs(th) , VARIANCE (VOLTS) VGS = 10 V ID = 0.8 A 1.8 1.6 VGS = 4.5 V ID = 0.5 A 1.4 1.2 1 1.125 1 0.875 0.8 0.6 -55 -5 45 95 0.75 -55 145 -30 -5 20 45 70 95 120 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 3. On-Resistance Variation with Temperature Figure 4. Threshold Voltage Variation with Temperature VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) RDS(on) , DRAIN-TO-SOURCE RESISTANCE (NORMALIZED) 25C 10 VDS = 40 V TJ = 25C 8 6 4 ID = 200 mA 2 0 0 500 1000 1500 2000 QT, TOTAL GATE CHARGE (pC) Figure 5. Gate Charge http://onsemi.com 3 2500 3000 145 BSS138LT1 10 VGS = 2.5 V 9 8 150C 7 6 5 25C 4 -55C 3 2 1 0.05 0 0.15 0.1 0.25 0.2 ID, DRAIN CURRENT (AMPS) RDS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS) RDS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS) TYPICAL ELECTRICAL CHARACTERISTICS 8 5 4 RDS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS) RDS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS) 150C 5 4.5 4 3.5 3 25C 2.5 2 -55C 1.5 1 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.45 0.4 25C 3 2 1 -55C 0.05 0 0.25 0.2 ID, DRAIN CURRENT (AMPS) 0.5 4.5 VGS = 10 V 4 150C 3.5 3 2.5 25C 2 -55C 1.5 1 0 0.05 0.1 ID, DRAIN CURRENT (AMPS) 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 ID, DRAIN CURRENT (AMPS) Figure 9. On-Resistance versus Drain Current Figure 8. On-Resistance versus Drain Current 1 I D , DIODE CURRENT (AMPS) 0.15 0.1 Figure 7. On-Resistance versus Drain Current VGS = 4.5 V 5.5 150C 6 Figure 6. On-Resistance versus Drain Current 6 VGS = 2.75 V 7 120 100 TJ = 150C 0.1 25C -55C 80 60 0.01 Ciss 40 Coss 20 0.001 0 0.2 0.4 0.6 0.8 1.0 0 1.2 Crss 0 5 10 15 VSD, DIODE FORWARD VOLTAGE (VOLTS) Figure 10. Body Diode Forward Voltage Figure 11. Capacitance http://onsemi.com 4 20 25 BSS138LT1 INFORMATION FOR USING THE SOT-23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT-23 POWER DISSIPATION one can calculate the power dissipation of the device which in this case is 225 milliwatts. The power dissipation of the SOT-23 is a function of the drain pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-23 package, PD can be calculated as follows: PD = PD = 150C - 25C 556C/W = 225 milliwatts The 556C/W for the SOT-23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT-23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. TJ(max) - TA RJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25C, SOLDERING PRECAUTIONS * The soldering temperature and time shall not exceed 260C for more than 10 seconds. * When shifting from preheating to soldering, the maximum temperature gradient shall be 5C or less. * After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. * Mechanical stress or shock should not be applied during cooling. The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10C. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 5 BSS138LT1 PACKAGE DIMENSIONS SOT-23 (TO-236) CASE 318-08 ISSUE AF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. A L 3 1 V B S 2 G C D H J K DIM A B C D G H J K L S V INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0140 0.0285 0.0350 0.0401 0.0830 0.1039 0.0177 0.0236 STYLE 21: PIN 1. GATE 2. SOURCE 3. DRAIN http://onsemi.com 6 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 BSS138LT1 Notes http://onsemi.com 7 BSS138LT1 Thermal Clad is a registered trademark of the Bergquist Company. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com Toll-Free from Mexico: Dial 01-800-288-2872 for Access - then Dial 866-297-9322 ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 BSS138LT1/D