SIDACtor (R) Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor(R) Series - TO-92 Description SIDACtor(R) Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a robust through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits t Low voltage overshoot t Fails short circuit when surged in excess of ratings t Low on-state voltage t Does not degrade with use Agency Approvals Agency t Low Capacitance Agency File Number Applicable Global Standards E133083 Pinout Designation Pin 1 t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level* t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* Pin 3 * A/B-rated parts require series resistance Schematic Symbol Electrical Characteristics Part Number Marking P0080EALxxx P0300EALxxx P0640EALxxx P0720EALxxx P0900EALxxx P1100EALxxx P1300EALxxx P1500EALxxx P1800EALxxx P2300EALxxx P2600EALxxx P3100EALxxx P3500EALxxx P0080EA P0300EA P0640EA P0720EA P0900EA P1100EA P1300EA P1500EA P1800EA P2300EA P2600EA P3100EA P3500EA VDRM @lDRM=5A VS @100V/s V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 2.2 2.2 2.2 2.2 2.2 2.2 25 15 40 35 35 30 25 25 25 25 20 20 20 150 140 60 60 55 50 45 40 35 35 35 35 35 Table continues on next page. (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 158 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) Part Number Marking P0080EBLxxx P0300EBLxxx P0640EBLxxx P0720EBLxxx P0900EBLxxx P1100EBLxxx P1300EBLxxx P1500EBLxxx P1800EBLxxx P2300EBLxxx P2600EBLxxx P3100EBLxxx P3500EBLxxx P0080ECLxxx P0300ECLxxx P0640ECLxxx P0720ECLxxx P0900ECLxxx P1100ECLxxx P1300ECLxxx P1500ECLxxx P1800ECLxxx P2300ECLxxx P2600ECLxxx P3100ECLxxx P3500ECLxxx P0080EB P0300EB P0640EB P0720EB P0900EB P1100EB P1300EB P1500EB P1800EB P2300EB P2600EB P3100EB P3500EB P0080EC P0300EC P0640EC P0720EC P0900EC P1100EC P1300EC P1500EC P1800EC P2300EC P2600EC P3100EC P3500EC VDRM @lDRM=5A VS @100V/s V Min V Max 6 25 58 65 75 90 120 140 170 190 220 275 320 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 25 40 77 88 98 130 160 180 220 260 300 350 400 IH mA Min mA Max 50 50 150 150 150 150 150 150 150 150 150 150 150 50 50 150 150 150 150 150 150 150 150 150 150 150 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A Max V Max pF Min pF Max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 IS 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 25 15 40 35 35 30 25 25 25 25 20 20 20 35 25 55 50 45 45 40 35 35 30 30 30 25 150 140 60 75 70 70 60 55 50 50 45 45 40 260 250 155 150 140 115 105 95 90 80 80 70 65 ITSM 50/60 Hz di/dt Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - xxx part number suffix: `AP' = Ammo Pack, `RP1' and `RP2' = Reel Pack, blank = Bulk Pack Series Surge Ratings IPP 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A min A min A/s max 20 150 150 90 50 75 75 45 75 20 500 A B 25 250 250 150 100 100 125 80 100 25 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: 1 Current waveform in s 2 Voltage waveform in s - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ - The device must initially be in thermal equilibrium with -40C < TJ < $ Thermal Considerations Package TO-92 Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP C TS Storage Temperature Range UP C R0JA Thermal Resistance: Junction to Ambient 90 C/W (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 159 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Baseband Protection (Voice-DS1) V-I Characteristics tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 td tr 0 t - Time (s) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature IH 8 6 25 C 4 IH (TC = 25C) 10 1.8 1.6 1.4 2 0 -4 25C 1.2 1.0 Ratio of Percent of VS Change - % 2.0 14 12 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) $ $ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Peak Temp (TP) tP Critical Zone TL to TP Ramp-up $ TL TS(max) tL Ramp-down TS(min) Preheat tS $ 25 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. TP 60-150 secs. Time within 5C of actual Peak Temp (tp) Do not exceed Figure 1 Temperature Reflow Condition time to peak temperature (t 25C to peak) $ 160 Revised: February 22, 2011 Time SIDACtor (R) Protection Thyristors Baseband Protection (Voice-DS1) Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak $PS $ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling $UP $ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC $ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage $IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock $UP $ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) $ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat $ TFDT.*-45% .FUIPE UL recognized epoxy meeting flammability classification 94V-0 Body Material Moisture Sensitivity Level 3) $ IST SFnPXDZDMFT $1FBL +&%&$+45% -FWFM Part Marking Part Numbering P xxx 0 E x L xxx TYPE P = SIDACtor PACKING OPTIONS MEDIAN VOLTAGE RoHS COMPLIANT CONSTRUCTION VARIABLE IPP RATING XXXXXXX XX Part Marking Code (Refer to Electrical Characteristics Table) Date Code XXXXX PACKAGE TYPE Packing Options Package Type Description Packing Options Quantity Added Suffix Lead Spacing RP1 0.1 inch (2.54mm) RP2 0.2 inch (5.08mm) TO-92 Tape and Reel Pack E 2000 Industry Standard EIA-481-D TO-92 Ammo Pack AP EIA-468-B TO-92 Bulk Pack N/A N/A (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 161 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors Baseband Protection (Voice-DS1) Dimensions -- TO-92 Ammo Pack Specification -- TO-92 Temperature Measurement Point Inches A N B MT1/PIN 1 MT2/PIN 3 E D Max Min Max 0.176 0.196 4.47 4.98 B 0.500 D 0.095 E 0.150 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 12.70 0.105 2.41 2.67 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 1.27 (32.2) 0.157 DIA (4.0) J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 0.20 (5.08) Flat down ed n of Fe Directio 25 Devices per fold 1.7 (43) 1.52 Dimensions are in inches (and millimeters). All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) K 0.125 (3.2) MAX 0.50 (12.7) 3.81 0.60 0.25 (6.35) 0.50 (12.7) G H L Min A N M Millimeters 6.9 (175) Mold flash shall not exceed 0.13 mm per side. 1.7 (43) 12.9 (327) Tape and Reel Specification -- TO-92 FLAT SIDE OF TO-92 Dimensions A A D W1 C B P H1 H W W3 ROUND SIDE OF TO-92 (RP1) W4 (RP2) W2 P0 (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. F F Inches Millimeters Min Max Min Max N/A 14.173 N/A 360.0 B 4.016 N/A 102.0 N/A C 3.386 N/A 86.0 N/A D 0.795 N/A 20.2 N/A W1 1.181 1.968 30.0 50.0 P 0.496 0.504 12.60 12.80 P0 0.498 0.502 12.65 12.75 F(for RP1) 0.090 0.110 2.29 2.80 F(for RP2) 0.182 0.244 4.63 6.19 H N/A 1.673 N/A 42.50 H1 N/A 1.270 N/A 32.26 W 0.674 0.763 17.12 19.38 W2 0.354 0.370 8.25 9.75 W3 0.236 N/A 6.00 N/A W4 0.020 N/A 0.50 N/A 162 Revised: February 22, 2011