INDUCTORS
MLZ1005 1005 [0402 inch]*
MLZ1608 1608 [0603 inch]
MLZ2012 2012 [0805 inch]
* Dimensions Code JIS[EIA]
September 2014
Inductors for Decoupling Circuits
Multilayer Ferrite
MLZseries
(2/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
Inductors for Decoupling Circuits
Multilayer Ferrite
FEATURES
The MLZ Series include inductors for decoupling circuits that have top-class DC superimposition characteristics and low DC resistance.
Sizes range from 1005 to 2012, and they are compatible with wide frequency band noise, from low to high frequency.
H type products have a rated current that is equivalent to that of wound coils.
W type products are the new standard type products that have both large current and low resistance.
L type products have a resistance up to 60% lower than W type products.
APPLICATION
Smart phones, tablet terminals, laptop computers, various modules such as camera modules, DSCs, video games, portable memory
audio devices, navigation systems, PNDs, WLANs, SSDs
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the MLZ Series
MLZ 1005 M R10 W T 000
Series name L×W×H Dimensions Product
internal code
Inductance Characteristic type Packaging style Internal code
(mm) (μH)
1005 1.0×0.5×0.5 A R10 0.1 H Ultra-large current type T Taping 000
1608 1.6×0.8×0.8 D 1R0 1 D High frequency type
2012 2.0×1.25×0.85 M 100 10 W Large current type
2012 2.0×1.25×1.25 N L Low resistance type
P
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MLZ1005 –55 to +125 –55 to +125 10000 1.2
MLZ1608 –55 to +125 –55 to +125 4000 4
MLZ2012 t=0.85 –55 to +125 –55 to +125 4000 10
t=1.25 2000 14
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
Overview of the MLZ Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series
MLZ1005 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.00±0.05
0.50±0.05 0.50±0.05
0.10min. 0.10min.
Dimensions in mm
0.5
0.5 0.4 0.5
(6/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
1Current assumed when inductance ratio has decreased by 50% max..
2Current assumed when temperature has risen to 20°C max. (reference value).
Operating temperature environment at this time: 105°C max.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Type
LL measuring conditions DC resistance
()±30%
Rated current1
(mA)
Rated current2
(mA) Part No.
(μH) Toleran ce Frequency
(MHz)
Current
(mA)
Large
current
0.47 ±20% 2 0.1 0.20 120 500 MLZ1005MR47WT000
0.68 ±20% 20.1 0.30 110 450 MLZ1005MR68WT000
1.00 ±20% 2 0.1 0.35 100 450 MLZ1005M1R0WT000
1.50 ±20% 20.1 0.50 80 350 MLZ1005M1R5WT000
2.20 ±20% 2 0.1 0.55 60 350 MLZ1005M2R2WT000
Measurement item Product No. Manufacturer
L 4294A+16034G Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1005 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
10
R47W
R68W
1R0W
1R5W
2R2W
Product No. Manufacturer
E4991A+16192ＡAgilent Technologies
(8/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1005 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.0
1.0
2.0
3.0
050 150100
DC current(mA)
Inductance(μH)
2R2W
1R5W
1R0W
R68W
R47W
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
(9/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1005 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
10000
10
Impedance(Ω)
Frequency(MHz)
R47W
2R2W
R68W
1R0W 1R5W
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(10/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series
MLZ1608 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.60±0.15
0.80±0.15 0.80±0.15
0.30±0.20 0.30±0.20
Dimensions in mm
0.8
0.6 0.8 0.6
(11/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
1Current assumed when inductance ratio has decreased by 50% max..
2Current assumed when temperature has risen to 20°C max. (reference value).
Operating temperature environment at this time: 105°C max.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Type
LL measuring conditions DC resistance
()±30%
Rated current1
(mA)
Rated current2
(mA) Part No.
(μH) Toleran ce Frequency
(MHz)
Current
(mA)
High
frequency
0.10 ±20% 25 1.0 0.14 700 850 MLZ1608DR10DT000
0.22 ±20% 25 1.0 0.27 550 600 MLZ1608DR22DT000
0.47 ±20% 25 1.0 0.42 400 500 MLZ1608DR47DT000
Large
current
1.00 ±20% 10 1.0 0.15 190 600 MLZ1608A1R0WT000
2.20 ±20% 10 1.0 0.25 130 500 MLZ1608A2R2WT000
4.70 ±20% 20.1 0.50 120 350 MLZ1608M4R7WT000
10.0 ±20% 2 0.1 1.05 90 250 MLZ1608M100WT000
22.0 ±20% 20.1 2.40 55 150 MLZ1608M220WT000
Low
resistance
1.00 ±20% 2 0.1 0.11 140 700 MLZ1608N1R0LT000
2.20 ±20% 20.1 0.18 110 500 MLZ1608N2R2LT000
4.70 ±20% 2 0.1 0.32 80 400 MLZ1608N4R7LT000
10.0 ±20% 20.1 0.60 60 300 MLZ1608N100LT000
22.0 ±20% 2 0.1 1.65 50 190 MLZ1608N220LT000
Measurement item Product No. Manufacturer
L 4294A+16034G Agilent Technologies
DC resistance Type-7561 Yokogawa
(12/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
100
10
DR10D
DR22D
DR47D
A1R0W
A2R2W
M4R7W
N1R0L
N2R2L
N4R7L
N100L
M220W
N220L
M100W
Product No. Manufacturer
E4991A+16192ＡAgilent Technologies
(13/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1608 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
DC current(mA)
Inductance(μH)
0.01
0.1
1
10
100
200 400 600 800 1000
N1R0L
N2R2L
N4R7L
N100L
DR10D
DR22D
DR47D
A1R0W
A2R2W
M4R7W
M220W
M100W
N220L
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
(14/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ1608 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
N220L
DR10D
DR22D
DR47D
A1R0W
A2R2W
M4R7W
N1R0L
N2R2L
N4R7L
N100L
M220W
M100W
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(15/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series
MLZ2012 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
2.00±0.20
T 1.25±0.20
0.50±0.30 0.50±0.30
T
0.85±0.20
1.25±0.20
Dimensions in mm
1.2
0.8 1.0 0.8
(16/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
1Current assumed when inductance ratio has decreased by 50% max..
2Current assumed when temperature has risen to 20°C max. (reference value).
Operating temperature environment at this time: 105°C max.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Type
LThickness T
(mm)
L measuring conditions DC resistance
()±30%
Rated
current1
(mA)
Rated
current2
(mA)
Part No.
(μH) Tolerance Frequency
(MHz)
Current
(mA)
Ultra-large
current
1.0 ±20% 1.25 2 0.1 0.10 700 800 MLZ2012M1R0HT000
1.5 ±20% 1.25 20.1 0.14 550 700 MLZ2012M1R5HT000
2.2 ±20% 1.25 2 0.1 0.16 400 600 MLZ2012M2R2HT000
3.3 ±20% 1.25 20.1 0.20 350 500 MLZ2012M3R3HT000
4.7 ±20% 1.25 2 0.1 0.34 300 400 MLZ2012M4R7HT000
6.8 ±20% 1.25 20.1 0.40 220 350 MLZ2012M6R8HT000
10 ±20% 1.25 2 0.1 0.68 200 300 MLZ2012M100HT000
High
frequency
0.10 ±20% 0.85 25 1.0 0.07 1000 1150 MLZ2012DR10DT000
0.22 ±20% 0.85 25 1.0 0.13 800 900 MLZ2012DR22DT000
0.47 ±20% 1.25 25 1.0 0.18 550 700 MLZ2012DR47DT000
Large current
1.00 ±20% 0.85 10 1.0 0.10 280 900 MLZ2012A1R0WT000
1.50 ±20% 0.85 10 1.0 0.13 250 750 MLZ2012A1R5WT000
2.20 ±20% 0.85 10 1.0 0.15 210 650 MLZ2012A2R2WT000
3.30 ±20% 0.85 10 1.0 0.34 200 450 MLZ2012A3R3WT000
4.70 ±20% 0.85 2 0.1 0.30 180 500 MLZ2012M4R7WT000
6.80 ±20% 1.25 20.1 0.40 160 400 MLZ2012M6R8WT000
10.0 ±20% 1.25 2 0.1 0.47 150 350 MLZ2012M100WT000
15.0 ±20% 1.25 20.1 0.95 120 250 MLZ2012M150WT000
22.0 ±20% 1.25 2 0.1 1.25 100 220 MLZ2012P220WT000
22.0 ±20% 1.25 20.1 2.0 60 220 MLZ2012M220WT000
33.0 ±20% 1.25 2 0.1 2.60 55 190 MLZ2012M330WT000
47.0 ±20% 1.25 20.1 3.70 50 170 MLZ2012M470WT000
Low
resistance
1.00 ±20% 0.85 2 0.1 0.06 220 1150 MLZ2012N1R0LT000
1.50 ±20% 0.85 20.1 0.10 190 900 MLZ2012N1R5LT000
2.20 ±20% 0.85 2 0.1 0.12 170 800 MLZ2012N2R2LT000
3.30 ±20% 0.85 20.1 0.15 130 750 MLZ2012N3R3LT000
4.70 ±20% 0.85 2 0.1 0.18 130 600 MLZ2012N4R7LT000
6.80 ±20% 0.85 20.1 0.25 110 550 MLZ2012N6R8LT000
10.0 ±20% 1.25 2 0.1 0.30 110 500 MLZ2012N100LT000
15.0 ±20% 1.25 20.1 0.47 90 350 MLZ2012N150LT000
22.0 ±20% 1.25 2 0.1 0.67 70 300 MLZ2012N220LT000
100.0 ±20% 1.25 20.1 3.50 30 140 MLZ2012N101LT000
Measurement item Product No. Manufacturer
L 4294A+16034G Agilent Technologies
DC resistance Type-7561 Yokogawa
(17/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.1
1
100
10
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
E4991A+16192ＡAgilent Technologies
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
1000
100
10
DR10D
DR22D
DR47D
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(18/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
1000
100
10
M100W
M150W
M220W
P220W
M330W
M470W
A1R0W
A1R5W
A2R2W
A3R3W
M4R7W
M6R8W
Product No. Manufacturer
E4991A+16192ＡAgilent Technologies
(19/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.1
1
1000
100
10
N1R0L
N1R5L
N2R2L
N3R3L
N4R7L
N6R8L
N100L
N150L
N220L
N101L
Product No. Manufacturer
E4991A+16192ＡAgilent Technologies
(20/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
200 400 600 800 1000
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
0
DC current(mA)
Inductance(μH)
0.01
0.1
1
10
200 400 600 800 1000
DR10D
DR22D
DR47D
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
(21/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH (EXAMPLE) W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
1000
100 200 300 400 500 600 700
M100W
M150W M220W
M470W
M4R7W
M6R8W
P220W
M330W
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
1000
100 200 300 400 500
N1R0L
N220L
N101L
N150L
N3R3L N4R7L
N6R8L
N100L
N1R5L
N2R2L
Product No. Manufacturer
4291B+16200A+16192A Agilent Technologies
(22/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
E4991A+16192A Agilent Technologies
110 1000100
1
100
1000
10000
10
Impedance(Ω)
Frequency(MHz)
DR10D
DR22D
DR47D
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(23/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
1000000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
M150W
M220W
P220W
M330W
M470W
A1R0W
M6R8W
A1R5W
A2R2W
M4R7W
A3R3W
M100W
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(24/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
N1R0L
N220L
N101L
N3R3L
N2R2L
N1R5L
N4R7L
N6R8L
N100L
N150L
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(25/25)
INDUCTORS
20140903 / inductor_commercial_decoupling_mlz_en.fm
• All specifications are subject to change without notice.
MLZ series
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
Typ e A B K t
MLZ1005 1.15±0.1 0.65±0.1 0.8 max. —
MLZ1608 1.9±0.2 1.1±0.2 1.1 max. —
MLZ2012 t=0.85 2.3±0.2 1.5±0.2 1.1 max.
t=1.25 2.3±0.2 1.5±0.2 1.5 max.
B
A
8.0±0.3
F 1.75±0.1
4.0±0.1
4.0±0.1
2.0±0.05
1.5 +0.1
0t
KK
MLZ1005,
MLZ1608,
MLZ2012 (t=1.25)MLZ2012 (t=0.85)
Dimensions in mm
160min. Taping 200min.
300min.
Drawing direction Dimensions in mm
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TDK:
MLZ2012E4R7P MLZ1608E4R7MT MLZ2012A2R2W MLZ2012A2R2M MLZ2012E4R7M MLZ2012E100M
MLZ1608N1R0L MLZ1608N2R2L MLZ2012N100L MLZ2012N150L MLZ2012N1R0L MLZ2012N1R5L
MLZ2012N2R2L MLZ2012N6R8L MLZ2012A1R0P MLZ1608A2R2M MLZ1608E4R7M MLZ1608A1R0MT
MLZ2012A1R0MT MLZ2012A2R2MT MLZ2012E100MT MLZ1608DR10D MLZ1608DR22D MLZ1608DR47D
MLZ1608A1R0W MLZ1608M100W MLZ2012DR10D MLZ2012DR22D MLZ2012DR47D MLZ2012A1R0W
MLZ2012A1R5W MLZ2012A3R3W MLZ2012M4R7W MLZ2012M100W MLZ2012M150W MLZ2012M220W
MLZ2012M330W MLZ2012M470W MLZ1005MR68W MLZ1005M1R0W MLZ1005M1R5W MLZ1005M2R2W
MLZ2012M100H MLZ2012M330WT000 MLZ1608DR10DT000 MLZ2012N4R7LT000 MLZ1608DR47DT000
MLZ2012A1R0WT000 MLZ2012M4R7WT000 MLZ2012N6R8LT000 MLZ2012N100LT000 MLZ2012M100WT000
MLZ2012N150LT000 MLZ2012N2R2LT000 MLZ2012DR10DT000 MLZ2012M220WT000 MLZ1005M2R2WT000
MLZ1608M100WT000 MLZ1608M4R7WT000 MLZ2012M470WT000 MLZ2012A2R2WT000 MLZ1608N1R0LT000
MLZ1005M1R0WT000 MLZ1608A1R0WT000 MLZ2012N1R0LT000 MLZ1608N2R2LT000 MLZ2012A3R3WT000
MLZ1608DR47DT MLZ2012N101LT000 MLZ2012N220LT000 MLZ2012N3R3LT000 MLZ1608DR22DT000
MLZ2012N1R5LT000 MLZ2012M6R8WT000 MLZ1005MR68WT000 MLZ1005MR47WT000 MLZ2012M150WT000
MLZ1608A2R2WT000
