LM2931 Series Low Dropout Regulators Both versions are available in a TO-220 power package, TO-263 surface mount package, and an 8-lead surface mount package. The fixed output version is also available in the TO-92 plastic package. General Description The LM2931 positive voltage regulator features a very low quiescent current of 1mA or less when supplying 10mA loads. This unique characteristic and the extremely low input-output differential required for proper regulation (0.2V for output currents of 10mA) make the LM2931 the ideal regulator for standby power systems. Applications include memory standby circuits, CMOS and other low power processor power supplies as well as systems demanding as much as 100mA of output current. Designed originally for automotive applications, the LM2931 and all regulated circuitry are protected from reverse battery installations or 2 battery jumps. During line transients, such as a load dump (60V) when the input voltage to the regulator can momentarily exceed the specified maximum operating voltage, the regulator will automatically shut down to protect both internal circuits and the load. The LM2931 cannot be harmed by temporary mirror-image insertion. Familiar regulator features such as short circuit and thermal overload protection are also provided. The LM2931 family includes a fixed 5V output (3.8% tolerance for A grade) or an adjustable output with ON/OFF pin. Features Very low quiescent current Output current in excess of 100 mA Input-output differential less than 0.6V Reverse battery protection 60V load dump protection -50V reverse transient protection Short circuit protection Internal thermal overload protection Mirror-image insertion protection Available in TO-220, TO-92, TO-263, or SO-8 packages Available as adjustable with TTL compatible switch Connection Diagrams FIXED VOLTAGE OUTPUT TO-220 3-Lead Power Package TO-263 Surface-Mount Package 525406 Front View 525411 Top View 525412 Side View 8-Pin Surface Mount TO-92 Plastic Package 525408 Bottom View 525407 *NC = Not internally connected. Must be electrically isolated from the rest of the circuit for the micro SMD package. Top View PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. 5254 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 6-Bump micro SMD micro SMD Laser Mark 525439 525438 Top View (Bump Side Down) ADJUSTABLE OUTPUT VOLTAGE TO-220 5-Lead Power Package TO-263 5-Lead Surface-Mount Package 525409 525413 Front View Top View 525414 Side View 8-Pin Surface Mount 525410 Top View 2 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Ordering Information Output Voltage Package Type NSC Drawing 8-Pin SOIC Narrow 5V 3-Pin TO-220 3-Pin TO-263 3-Pin TO-92 Adjustable 3V to 24V M08A T03B TS3B Z03A Order Number Package Marking Transport Media LM2931AM-5.0 2931AM-5.0 Rail of 95 LM2931AMX-5.0 2931AM-5.0 Reel of 2500 LM2931M-5.0 2931M-5.0 Rail of 95 LM2931MX-5.0 2931M-5.0 Reel of 2500 LM2931AT-5.0 LM2931AT5.0 Rail of 45 Rail of 45 LM2931T-5.0 LM2931T5.0 LM2931AS-5.0 LM2931AS5.0 Rail of 45 LM2931ASX-5.0 LM2931AS5.0 Reel of 500 LM2931S-5.0 LM2931S5.0 Rail of 45 LM2931AZ-5.0 LM2931AZ-5 Box of 1800 LM2931Z-5.0 LM2931Z-5 Box of 1800 LM2931CM LM2931CM Rail of 95 8-Pin SOIC Narrow M08A LM2931CMX LM2931CM Reel of 2500 5-Pin TO-220 T05A LM2931CT LM2931CT Rail of 45 5-Pin TO-263 TS5B LM2931CS LM2931CS Rail of 45 Copyright (c) 1999-2012, Texas Instruments Incorporated 3 LM2931 Typical Applications LM2931 Fixed Output 525404 *Required if regulator is located far from power supply filter. **C2 must be at least 100 F to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to the regulator. This capacitor must be rated over the same operating temperature range as the regulator. The equivalent series resistance (ESR) of this capacitor is critical; see curve. LM2931 Adjustable Output 525405 Note: Using 27k for R1 will automatically compensate for errors in VOUT due to the input bias current of the ADJ pin (approximately 1 A). 4 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Input Voltage Operating Range Overvoltage Protection LM2931A, LM2931C (Adjustable) LM2931 Internal Power Dissipation (Note 2, Note 4) Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Lead Temp. (Soldering, 10 seconds) ESD Tolerance (Note 5) 26V 60V 50V Internally Limited -40C to +85C 125C -65C to +150C 230C 2000V Electrical Characteristics for Fixed 3.3V Version VIN = 14V, IO = 10mA, TJ = 25C, C2 = 100F (unless otherwise specified) (Note 2) LM2931-3.3 Parameter Conditions Output Voltage Typ 3.3 4V VIN 26V, IO = 100 mA -40C TJ 125C Limit (Note 3) Units 3.465 3.135 VMAX VMIN 3.630 2.970 VMAX VMIN Line Regulation 4V VIN 26V 4 33 mVMAX Load Regulation 5mA IO 100mA 10 50 mVMAX Output Impedance 100mADC and 10mArms, 100Hz - 10kHz 200 Quiescent Current IO 10mA, 4V VIN 26V 0.4 m 1.0 mAMAX -40C TJ 125C Output Noise Voltage IO = 100mA, VIN = 14V, TJ = 25C 15 10Hz -100kHz, COUT = 100F 330 Vrms 13 mV/1000 hr Long Term Stability mA Ripple Rejection fO = 120Hz 80 Dropout Voltage IO = 10mA IO = 100mA 0.05 0.30 0.2 0.6 VMAX 33 26 VMIN 70 50 VMIN -30 -15 VMIN -80 -50 VMIN Maximum Operational Input Voltage Maximum Line Transient RL = 500, VO 5.5V, dB T = 1ms, 100ms Reverse Polarity Input Voltage, DC VO -0.3V, RL = 500 Reverse Polarity Input Voltage, Transient T = 1ms, 100ms, RL = 500 Copyright (c) 1999-2012, Texas Instruments Incorporated 5 LM2931 Electrical Characteristics for Fixed 5V Version VIN = 14V, IO = 10mA, TJ = 25C, C2 = 100 F (unless otherwise specified) (Note 2) LM2931A-5.0 Parameter Conditions Output Voltage Typ 5 6.0V VIN 26V, IO = 100mA Limit (Note 3) 5.19 4.81 LM2931-5.0 Typ 5 5.25 4.75 -40C TJ 125C Limit (Note 3) Units 5.25 4.75 VMAX VMIN 5.5 4.5 VMAX VMIN 9V VIN 16V 2 4 10 30 2 4 10 30 mVMAX Load Regulation 5 mA IO 100mA 14 50 14 50 mVMAX Output Impedance 100mADC and 10mArms, 100Hz -10kHz 200 Quiescent Current IO 10mA, 6V VIN 26V 0.4 1.0 IO = 100mA, VIN = 14V, TJ = 25C 15 30 15 mAMAX 10Hz -100kHz, COUT = 100F 500 500 Vrms 20 20 mV/1000 hr Line Regulation 6V VIN 26V 200 0.4 m 1.0 mAMAX -40C TJ 125C Output Noise Voltage Long Term Stability Ripple Rejection fO = 120 Hz 80 55 80 Dropout Voltage IO = 10mA IO = 100mA 0.05 0.3 0.2 0.6 0.05 0.3 0.2 0.6 VMAX 33 26 33 26 VMIN 70 60 70 50 VMIN Reverse Polarity Input Voltage, VO -0.3V, RL = 500 DC -30 -15 -30 -15 VMIN Reverse Polarity Input Voltage, T = 1ms, 100ms, RL = 500 Transient -80 -50 -80 -50 VMIN Maximum Operational Input Voltage Maximum Line Transient RL = 500, VO 5.5V, T = 1ms, 100ms dBMIN Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: See circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. Note 3: All limits are guaranteed for TJ = 25C (standard type face) or over the full operating junction temperature range of -40C to +125C (bold type face). Note 4: The maximum power dissipation is a function of maximum junction temperature TJmax, total thermal resistance JA, and ambient temperature TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax - TA)/JA. If this dissipation is exceeded, the die temperature will rise above 150 C and the LM2931 will go into thermal shutdown. For the LM2931 in the TO-92 package, JA is 195C/W; in the SO-8 package, JA is 160C/W, and in the TO-220 package, JA is 50C/W; in the TO-263 package, JA is 73C/W; and in the 6-Bump micro SMD package JA is 290C/W. If the TO-220 package is used with a heat sink, JA is the sum of the package thermal resistance junction-to-case of 3C/W and the thermal resistance added by the heat sink and thermal interface. If the TO-263 package is used, the thermal resistance can be reduced by increasing the P.C. board copper area thermally connected to the package: Using 0.5 square inches of copper area, JA is 50C/W; with 1 square inch of copper area, JA is 37C/W; and with 1.6 or more square inches of copper area, JA is 32C/ W. Note 5: Human body model, 100 pF discharged through 1.5 k. 6 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Electrical Characteristics for Adjustable Version VIN = 14V, VOUT = 3V, IO = 10 mA, TJ = 25C, R1 = 27k, C2 = 100 F (unless otherwise specified) (Note 2) Parameter Conditions Reference Voltage Typ Limit Units Limit 1.20 1.26 VMAX 1.14 VMIN IO 100 mA, -40C Tj 125C, R1 = 27k 1.32 VMAX Measured from VOUT to Adjust Pin 1.08 VMIN 24 VMAX Output Voltage Range 3 VMIN 1.5 mV/VMAX 1 %MAX Line Regulation VOUT + 0.6V VIN 26V 0.2 Load Regulation 5 mA IO 100 mA 0.3 Output Impedance 100 mADC and 10 mArms, 100 Hz-10 kHz 40 Quiescent Current IO = 10 mA 0.4 IO = 100 mA 15 During Shutdown RL = 500 0.8 10 Hz-100 kHz 100 Vrms/V 0.4 %/1000 hr Ripple Rejection fO = 120 Hz 0.02 %/V Dropout Voltage IO 10 mA 0.05 0.2 VMAX IO = 100 mA 0.3 0.6 VMAX 33 26 VMIN 70 60 VMIN -30 -15 VMIN -80 -50 VMIN On 2.0 1.2 VMAX Off 2.2 3.25 VMIN 20 50 AMAX Output Noise Voltage Long Term Stability Maximum Operational Input Voltage Maximum Line Transient IO = 10 mA, Reference Voltage 1.5V m/V 1 mAMAX 1 mAMAX mA T = 1 ms, 100 ms Reverse Polarity Input VO -0.3V, RL = 500 Voltage, DC Reverse Polarity Input T = 1 ms, 100 ms, RL = 500 Voltage, Transient On/Off Threshold Voltage VO=3V On/Off Threshold Current Copyright (c) 1999-2012, Texas Instruments Incorporated 7 LM2931 Typical Performance Characteristics Dropout Voltage Dropout Voltage 525417 525416 Low Voltage Behavior Output at Voltage Extremes 525418 Line Transient Response Load Transient Response 525420 8 525419 525421 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Peak Output Current Quiescent Current 525423 525422 Quiescent Current Quiescent Current 525424 Ripple Rejection Ripple Rejection 525426 Copyright (c) 1999-2012, Texas Instruments Incorporated 525425 525427 9 LM2931 Output Impedance Operation During Load Dump 525428 525429 Reference Voltage Maximum Power Dissipation (SO-8) 525430 525431 Maximum Power Dissipation (TO-220) Maximum Power Dissipation (TO-92) 525432 10 525433 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Maximum Power Dissipation (TO-263) (Note 4) On/Off Threshold 525435 525434 Output Capacitor ESR 525436 Copyright (c) 1999-2012, Texas Instruments Incorporated 11 LM2931 Schematic Diagram 525401 12 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 Application Hints One of the distinguishing factors of the LM2931 series regulators is the requirement of an output capacitor for device stability. The value required varies greatly depending upon the application circuit and other factors. Thus some comments on the characteristics of both capacitors and the regulator are in order. High frequency characteristics of electrolytic capacitors depend greatly on the type and even the manufacturer. As a result, a value of capacitance that works well with the LM2931 for one brand or type may not necessary be sufficient with an electrolytic of different origin. Sometimes actual bench testing, as described later, will be the only means to determine the proper capacitor type and value. Experience has shown that, as a rule of thumb, the more expensive and higher quality electrolytics generally allow a smaller value for regulator stability. As an example, while a high-quality 100 F aluminum electrolytic covers all general application circuits, similar stability can be obtained with a tantalum electrolytic of only 47F. This factor of two can generally be applied to any special application circuit also. Another critical characteristic of electrolytics is their performance over temperature. While the LM2931 is designed to operate to -40C, the same is not always true with all electrolytics (hot is generally not a problem). The electrolyte in many aluminum types will freeze around -30C, reducing their effective value to zero. Since the capacitance is needed for regulator stability, the natural result is oscillation (and lots of it) at the regulator output. For all application circuits where cold operation is necessary, the output capacitor must be rated to operate at the minimum temperature. By coincidence, worst-case stability for the LM2931 also occurs at minimum temperatures. As a result, in applications where the regulator junction temperature will never be less than 25C, the output capacitor can be reduced approximately by a factor of two over the value needed for the entire temperature range. To continue our example with the tantalum electrolytic, a value of only 22F would probably thus suffice. For high-quality aluminum, 47F would be adequate in such an application. Another regulator characteristic that is noteworthy is that stability decreases with higher output currents. This sensible fact has important connotations. In many applications, the LM2931 is operated at only a few milliamps of output current or less. In such a circuit, the output capacitor can be further reduced in value. As a rough estimation, a circuit that is required to deliver a maximum of 10mA of output current from the regulator would need an output capacitor of only half the value compared to the same regulator required to deliver the full output current of 100mA. If the example of the tantalum capacitor in the circuit rated at 25C junction temperature and above were continued to include a maximum of 10mA of output current, then the 22F output capacitor could be reduced to only 10F. In the case of the LM2931CT adjustable regulator, the minimum value of output capacitance is a function of the output voltage. As a general rule, the value decreases with higher output voltages, since internal loop gain is reduced. At this point, the procedure for bench testing the minimum value of an output capacitor in a special application circuit should be clear. Since worst-case occurs at minimum operating temperatures and maximum operating currents, the entire circuit, including the electrolytic, should be cooled to the minimum temperature. The input voltage to the regulator should be maintained at 0.6V above the output to keep internal power dissipation and die heating to a minimum. Worst-case occurs just after input power is applied and before the die has had a chance to heat up. Once the minimum value of capacitance has been found for the brand and type of electrolytic in question, the value should be doubled for actual use to account for production variations both in the capacitor and the regulator. (All the values in this section and the remainder of the data sheet were determined in this fashion.) LM2931 micro SMD Light Sensitivity When the LM2931 micro SMD package is exposed to bright sunlight, normal office fluorescent light, and other LED's, it operates within the guaranteed limits specified in the electrical characteristic table. Definition of Terms Dropout Voltage: The input-output voltage differential at which the circuit ceases to regulate against further reduction in input voltage. Measured when the output voltage has dropped 100 mV from the nominal value obtained at 14V input, dropout voltage is dependent upon load current and junction temperature. Input Voltage: The DC voltage applied to the input terminals with respect to ground. Input-Output Differential: The voltage difference between the unregulated input voltage and the regulated output voltage for which the regulator will operate. Line Regulation: The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation: The change in output voltage for a change in load current at constant chip temperature. Long Term Stability: Output voltage stability under accelerated life-test conditions after 1000 hours with maximum rated voltage and junction temperature. Output Noise Voltage: The rms AC voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Quiescent Current: That part of the positive input current that does not contribute to the positive load current. The regulator ground lead current. Ripple Rejection: The ratio of the peak-to-peak input ripple voltage to the peak-to-peak output ripple voltage at a specified frequency. Temperature Stability of VO: The percentage change in output voltage for a thermal variation from room temperature to either temperature extreme. Copyright (c) 1999-2012, Texas Instruments Incorporated 13 LM2931 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Surface Mount Package (M) NS Package Number M08A 3-Lead TO-220 Plastic Package (T) NS Package Number T03B 14 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 5-Lead TO-220 Power Package (T) NS Package Number T05A 3-Lead TO-263 Surface Mount Package NS Package Number TS3B Copyright (c) 1999-2012, Texas Instruments Incorporated 15 LM2931 5-Lead TO-263 Surface Mount Package NS Package Number TS5B 3-Lead TO-92 Plastic Package (Z) NS Package Number Z03A 16 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2931 NOTE: UNLESS OTHERWISE SPECIFIED. 1. EPOXY COATING. 2. 63Sn/37Pb EUTECTIC BUMP. 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEST ORIENTATION PINS ARE NUMBERED COUNTERCLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC. 6-Bump micro SMD NS Package Number BPA06HTB X1 = 0.955 X2 = 1.717 X3 = 0.850 Copyright (c) 1999-2012, Texas Instruments Incorporated 17 Notes Copyright (c) 1999-2012, Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated