* * * * * * * T2L LV CMOS input and outputs Output wavetrain can be started in sync with random events 8-pin Space Saver package Leads - thru-hole, J, Gull Wing or Tucked circuitry and of passive networks utilizing capacitive, inductive and resistive elements. The MTBF on these modules, when calculated per MIL-HDBK-217 for a 50o C ground fixed environment, is in excess of 4 million hours. Available in frequencies from 2 MHz to 80 MHz Output frequencies controlled to within 2% 12mA output drive capability design notes The LVQ "Space Saver Series" Gated Square Wave Generator modules developed by Engineered Components Company have been designed to provide a square wave output at frequencies from 2 MHz to 80 MHz. These generators are both keyable and synchronizable, producing a continuous output train as long as a zero (low) is maintained at the enable input. As long as the enable input is a "1" (high), OUT1 will be a constant "1" (high) and OUT2 will be a constant "0" (low). Whenever the enable input goes low, OUT2 goes high immediately. OUT1 and OUT2 go low together after a one-half cycle delay and, thereafter run in phase. When enable input returns to high, OUT2 is forced low immediately and OUT1 is forced high onehalf cycle later. (Note: The output buffers will add one propagation delay to all times). These Gated Square Wave Generator modules are of hybrid construction utilizing the proven technologies of active integrated The SSGSWG-LVQ is offered in 28 different frequencies from 2 MHz to 80 MHz. Output frequencies are controlled to within 2% and have a temperature coefficient of less than 600 ppm/oC over the operating temperature range of -40 to +85oC. These LVQ "Space Saver Series" modules are packaged in an 8-pin housing, molded of flame-proof Diallyl Phthalate per MIL-M-14, Type SDG-F, and are fully encapsulated in epoxy resin. Thru-hole, J, Gull Wing or Tucked Lead configurations are available on these modules (see Part Number Table note to specify). Leads meet the solderability requirements of MILSTD-202, Method 208. Corner standoffs on the housing of the thru-hole lead version and lead design of the surface mount versions provide positive standoff from the printed circuit board to permit solder-fillet formation and flush cleaning of solder-flux residues for improved reliability. Marking consists of manufacturer's name, logo (EC2), part number, terminal identification and date code of manufacture. All marking is applied by silk screen process using white epoxy paint in accordance with MIL-STD-130, to meet the permanency of identification required by MIL-STD-202, Method 215. BLOCK DIAGRAM IS SHOWN BELOW OUT 2 7 Vcc 8 X INPUT 5 X X SQUARE WAVE OSCILLATOR OUTPUT BUFFER TEST CONDITIONS 1. All measurements are made at 25oC. 2. Vcc supply voltage is maintained at 3.3V DC. 3. All units are tested using a LVQ gate driving the input and one LVQ gate load at the output. OPERATING SPECIFICATIONS . . . . . . . . . . . . 2.7 to 3.6V DC Vcc supply current: SSGSWG-LVQ-2 . . . . . . . . . . . 4mA typical SSGSWG-LVQ-80 . . . . . . . . . . 20mA typical (Current increases with operating frequency) * Vcc supply voltage: 4 GROUND 1 OUT1 MECHANICAL DETAIL IS SHOWN BELOW Pin No. 8 7 V O2 Pin No. 5 IN O1 C 1 4 Logic 1 Input: Voltage . . . . . . . . . . . . . . . . . Current . . . . . . . . . . . . . . . . . 2V min.; Vcc max. Vcc max.; 1uA max. Logic 0 Input: Voltage . . . Current . . . .8V max. 1A max. Logic 0 Voltage out: . . . . . . . . . . . Operating temperature range: . . . . . . Storage temperature: . . . . . . . . . . . 2.2V min.; Vcc 3.0; IOH -12mA .4V max. IOL +12mA -40 to +85oC. 55 to +125oC. .............. .............. Logic 1 Voltage out: . . . . . . . . . . . * Output frequency will increase or decrease less than 2% for a respective increase or decrease of 10% in supply voltage. PART NUMBER TABLE Thru-hole Lead Suffix Part Number with G (for Gull Wing Lead), J (for J Lead), F (for Thru-hole Lead) or T (for Tucked Lead). Examples: SSGSWGLVQ-10G (Gull Wing), SSGSWG-LVQ-25J (J Lead), SSGSWGLVQ-70F (Thru-hole Lead) or SSGSWG-LVQ-12T (Tucked Lead). OUTPUT FREQUENCY PART NUMBER OUTPUT FREQUENCY SSGSWG-LVQ-2 2.0 MHz SSGSWG-LVQ-12 12.0 MHz SSGSWG-LVQ-2.5 2.5 MHz SSGSWG-LVQ-13 13.0 MHz SSGSWG-LVQ-3 3.0 MHz SSGSWG-LVQ-14 14.0 MHz SSGSWG-LVQ-3.5 3.5 MHz SSGSWG-LVQ-15 15.0 MHz SSGSWG-LVQ-4 4.0 MHz SSGSWG-LVQ-20 20.0 MHz SSGSWG-LVQ-4.5 4.5 MHz SSGSWG-LVQ-25 25.0 MHz SSGSWG-LVQ-5 5.0 MHz SSGSWG-LVQ-30 30.0 MHz SSGSWG-LVQ-5.5 5.5 MHz SSGSWG-LVQ-35 35.0 MHz SSGSWG-LVQ-6 6.0 MHz SSGSWG-LVQ-40 40.0 MHz SSGSWG-LVQ-7 7.0 MHz SSGSWG-LVQ-45 45.0 MHz SSGSWG-LVQ-8 8.0 MHz SSGSWG-LVQ-50 50.0 MHz SSGSWG-LVQ-9 9.0 MHz SSGSWG-LVQ-60 60.0 MHz SSGSWG-LVQ-10 10.0 MHz SSGSWG-LVQ-70 70.0 MHz SSGSWG-LVQ-11 11.0 MHz SSGSWG-LVQ-80 80.0 MHz PART NUMBER Gull Wing Lead J Lead Special modules can be readily manufactured to improve accuracies and/or provide customer specified non-standard frequencies for specific applications. Tucked Lead Catalog No. C/031197R