Type 112 No.P-112-E001 Type 112 is hermetically sealed capacitors in metal case, designed for high reliability. FEATURES 1. Type 112 is smaller and larger capacitance compared with Type 111. 2. The type is hermetically sealed capacitors in metal case, designed for excellent stability. 3. Designed for high reliability. 4. Available for capacitance tolerance code "J"(5%). RATING Item Rating Category temperature range (Operating temperature ) -55 ~ +125C Rated Temperature (Maximum operating temperature for DC rated Voltage) +85C (1) DC rated voltage rangeUR See CATALOG NUMBERS AND Rated capacitance (Normal capacitance rangeCR) RATING OF STANDARD PRODUCTS Rated capacitance tolerance Failure rate level 1%/1000 h Note(1): For operation 125,derate voltage linearly to 67% of 85 voltage rating. ORDERING INFORMATION 112 TYPE Marking 6301 1002 1602 2002 2502 3502 5002 Rated voltage 6.3VDC 10VDC 16VDC 20VDC 25VDC 35VDC 50VDC M 1602 SERIES RATED VOLTAGE Marking Capacitance Marking Capacitance 155 225 335 475 685 106 1.5 m 2.2 m 3.3 m 4.7 m 6.8 m 10 m 15 m 22 m 33 m 47 m 68 m 100 m 156 226 336 476 686 107 475 M CAPACITANCE CAPACITANCE TOLERANCE Marking Capacitance Marking 157 227 337 477 687 108 150 m 220 m 330 m 470 m 680 m 1000 m K M DIMENSIONS L+2.0 max 0.7 max d 405 405 Unit : mm d Case size D0.5 L1 A 3.15 6.3 0.5 E 4.5 10.0 0.5 +0.1 -0.025 +0.1 -0.025 B 4.5 11.5 0.5 +0.1 -0.025 H 6.3 12.5 0.65 +0.12 -0.03 C 7.1 16.0 0.65 +0.12 -0.03 D 8.7 19.5 0.65 +0.12 -0.03 1 Capacitance Tolerance 10% 20% MARKING Manufacture's identification NCC 10M 35V 01 1 Rated capacitance (10mF) Capacitance tolerance (M:+/-20%) Rated voltage (35V) Date code (01 1: Jan./2011) Series code STANDARD RATING R.V.(VDC) Cap.( mF ) 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 6.3 10 16 20 25 A A A A E E E B H H C C D D 50 A E E E E E E E A E E 35 B B B B B H H C C D D H H C D D C D D D 2 B H H C C D D B H C D CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS March, 2011 Catalog Number (1) 1 112 M 6301 106 _ 1 112 M 6301 336 _ 1 112 M 6301 476 _ 1 112 M 6301 107 _ 1 112 M 6301 157 _ 1 112 M 6301 227 _ 1 112 M 6301 337 _ 1 112 M 6301 477 _ 1 112 M 6301 687 _ 1 112 M 6301 108 _ 1 112 M 1002 685 _ 1 112 M 1002 226 _ 1 112 M 1002 476 _ 1 112 M 1002 686 _ 1 112 M 1002 107 _ 1 112 M 1002 227 _ 1 112 M 1002 477 _ 1 112 M 1602 475 _ 1 112 M 1602 156 _ 1 112 M 1602 336 _ 1 112 M 1602 686 _ 1 112 M 1602 157 _ 1 112 M 1602 227 _ 1 112 M 1602 337 _ 1 112 M 2002 335 _ 1 112 M 2002 106 _ 1 112 M 2002 226 _ 1 112 M 2002 476 _ 1 112 M 2002 107 _ 1 112 M 2002 157 _ 1 112 M 2002 227 _ 1 112 M 2502 225 _ 1 112 M 2502 685 _ 1 112 M 2502 156 _ 1 112 M 2502 336 _ 1 112 M 2502 686 _ 1 112 M 2502 107 _ 1 112 M 2502 157 _ 1 112 M 3502 155 _ 1 112 M 3502 225 _ 1 112 M 3502 335 _ 1 112 M 3502 475 _ 1 112 M 3502 106 _ 1 112 M 3502 156 _ 1 112 M 3502 226 _ 1 112 M 3502 336 _ 1 112 M 3502 476 _ 1 112 M 3502 686 _ 1 112 M 3502 107 _ 1 112 M 5002 155 _ 1 112 M 5002 225 _ 1 112 M 5002 335 _ 1 112 M 5002 685 _ 1 112 M 5002 106 _ 1 112 M 5002 226 _ 1 112 M 5002 336 _ UR US CR VDC VDC F Case code 6.3 10 16 20 25 35 50 8 13 20 25 32 44 63 10 33 47 100 150 220 330 470 680 1000 6.8 22 47 68 100 220 470 4.7 15 33 68 150 220 330 3.3 10 22 47 100 150 220 2.2 6.8 15 33 68 100 150 1.5 2.2 3.3 4.7 10 15 22 33 47 68 100 1.5 2.2 3.3 6.8 10 22 33 A E E B H H C C D D A E B B H C D A E B H C D D A E B H C D D A E B H C D D A E E E B H H C C D D E E E B H C D UR = Rated Voltage US = Surge Voltage CR = Capacitance Note1 : For Capacitance tolerance , insert "K" or "M" into _1 3 Leakage current(DCL) A Dissipation factor 20 85 125 -55 20 85 125 0.6 2.1 3.0 6.3 9.5 14 21 30 43 63 0.7 2.2 4.7 6.8 10 22 47 0.8 2.4 5.3 11 24 35 53 0.7 2.0 4.4 9.4 20 30 44 0.6 1.7 3.8 8.3 17 25 37 0.5 0.8 1.2 1.6 3.5 5.3 7.7 12 16 24 35 0.8 1.1 1.7 3.4 5.0 11 17 6 21 30 63 95 140 210 300 430 630 7 22 47 68 100 220 470 8 24 53 110 240 350 530 7 20 44 94 200 300 440 6 17 38 83 170 250 370 5 8 12 16 35 53 77 120 160 240 350 8 11 17 34 50 110 170 7.9 26 37 79 118 173 260 370 536 788 8.5 28 59 85 125 275 588 9.4 30 66 136 300 440 660 8.3 25 55 118 250 375 550 6.9 21 47 103 213 313 468 6.6 9.6 14 21 44 66 96 144 206 298 437 9.4 14 21 43 63 138 206 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.10 0.10 0.12 0.06 0.06 0.06 0.06 0.08 0.08 0.10 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.06 0.08 0.08 0.04 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.10 0.10 0.12 0.06 0.06 0.06 0.06 0.08 0.08 0.10 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.06 0.08 0.08 0.04 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.10 0.10 0.15 0.06 0.06 0.06 0.06 0.08 0.08 0.10 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.08 0.08 0.08 0.04 0.06 0.06 0.06 0.06 0.08 0.08 0.04 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.04 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.12 0.12 0.15 0.06 0.06 0.06 0.06 0.08 0.08 0.12 0.05 0.06 0.06 0.06 0.08 0.08 0.08 0.05 0.06 0.06 0.06 0.08 0.08 0.08 0.05 0.06 0.06 0.06 0.06 0.08 0.08 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.05 0.05 0.05 0.06 0.06 0.06 0.06 PERFORMANCE No. Item Performance Leakage Current (A) Shall not exceed 0.01 CV or 0.5 whichever is greater. Capacitance (F) Shall be within tolerance of the nominal value specified. Dissipation Factor Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS. 1 2 3 4 5 6 Characteristics at High and LowTemperature Leakage Current Step1 Capacitance Dissipation Factor Capacitance Change Step2 Dissipation Factor Leakage Current Capacitance Step3 Change Dissipation Factor Leakage Current Capacitance Step4 Change Dissipation Factor Leakage Current Capacitance Step5 Change Dissipation Factor Leakage Current Capacitance Step6 Change Dissipation Factor Surge Leakage Current Capacitance Change Dissipation Factor Appearance Sleeving Dielectric withstanding voltage Insulation resistanc Terminal strength 7 Tensile strength Shall not exceed the value in No.1. Test method JIS C 5101-1,4.9 Applied Voltage : Rated Voltage for 5 min. Temperature : 20C JIS C 5101-1,4.7 Frequency : 120 Hz 20% Voltage : 0.5Vrms+1.5 ~2VDC Temperature : 20C JIS C 5101-1,4.8 Frequency : 120 Hz 20% Voltage : 0.5Vrms+1.5 ~2VDC Temperature : 20C JIS C 5101-1,4.29 Measuring temperature : 20 2C Shall be within the specified tolerance. Shall not exceed the value in No.3. Shall be within 10% of the value at Step 1. Measuring temperature : -55 3C Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS. Shall not exceed the value in No.1. Measuring temperature : 20 2C Shall be within 2% of the value at Step 1. Shall not exceed the value in No.3. Shall not exceed 0.1 CV or 5 whichever is greater. Measuring temperature : 85 2C Shall be within 8% of the value at Step 1. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS. Shall not exceed 0.125 CV or 6.3 whichever is greater. Measuring temperature : 125 2C Shall be within 12% of the value at Step 1. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS. Shall not exceed the value in No.1. Measuring temperature : 20 2C Shall be within 2% of the value at Step 1. Shall not exceed the value in No.3. Shall not exceed the value in No.1. Shall be within 5% of initial value. Shall not exceed the value in No.3. JIS C 5101-1,4.26 Test temperature : 85 2C, Applied Voltage :DC surge voltage Series protective resistance : 1000 Discharge resistance : 1000 There shall be no evidence of mechanical damage. There shall be no dielectric breakdown. More than 1000M No fault such as breakage and loosening terminal Bending strength 4 JIS C 5101-1,4.6(c) Voltage: 2000VDC Duration : 1 min. JIS C 5101-1,4.5(c) Voltage: 100VDC Duration : 2 min. JIS C 5101-1,4.13.1 Applied force: 5N (d=0.5) ,10N (d=0.65) Duration:10 1 s JIS C 5101-1,4.13.2 Bending force : 2.5N (d=0.5), 5N (d=0.65) Bending cycle:2 No. Item Vibration 8 Performance Capacitance Initial value to remain steady during measurement. Appearance There shall be no evidence of mechanical damage. Shock There shall be no intermittent contact of 0.5 ms or greater, short, or open. Nor shall there be any spark discharge, insulation breakdown, or evidence of mechanical damage. Shall be covered to over 3/4 of terminal surface by new soldering. 9 Solderability 10 11 Resistance to Soldering Heat 12 Component solvent resistance 13 Solvent resistance of marking Leakage Current Capacitance Change Dissipation Factor Appearance Appearance Shall not exceed the value in No.1. Visual examination After the test the marking shall be legible. Seal Shall be within 3% of initial value. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. There shall be no evidence of mechanical damage. There shall be no evidence of leakage. 14 Rapid Change of Temperature and immersion cycle 15 Moisture resistance 16 Rapid Change of Temperature Immersion cycle Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change Dissipation Factor Appearance Salt spray 17 Endurance 18 Leakage Current Capacitance Change Dissipation Factor Appearance Measurements after cycling, are not applicable. Shall not exceed the value in No.1. Shall be within 5% of initial value. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. Shall not exceed the value in No.1. Shall be within 5% of initial value. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. There shall be no harmful corrosion, and at least 90% of any exposed surfaca of the capacitor shall be protected by the finish. There shall be no unwraping of, or mechanical damage to, the sleeving. Marking shall remain legible. Shall not exceed the value in No.1. Shall be within 5% of initial value. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. 5 Test method JIS C 5101-1,4.17 Frequency range : 10 ~ 2000 Hz Swing width : 1.5 mm 2 Peak acceleration : 196m/s Vibration direction : 2 directions with mutually right-angled Duration : 4 hours in each of these mutually perpendicular directions (total 8 hours) JIS C 5101-1,4.19 2 Peak acceleration :981 m/s (100G) Duration : 6 ms Wave form : Sawtooth JIS C 5101-1,4.15 Solder temperature : 230 5C Dipping time : 2 0.5 s Dipping depth : 2.0 to 2.5 mm from the terminal base JIS C 5101-1,4.14 Solder temperature: 260 5C Dipping time: 10 1 s Dipping depth : 2.0 to 2.5 mm from the terminal base JIS C 5101-1, 4.31 Temperature : 23 5C Dipping time : 5 0.5 min. Solvent : 2-propanol (Isopropyl alcohol) JIS C 5101-1, 4.32 Temperature : 23 5C Dipping time : 5 0.5 min. Solvent : 2-propanol (Isopropyl alcohol) JIS C 5101-1,4.20 Test condition : Qc, method 1 Temperature : 125 +5 -1 C Duration : 1min. JIS C 5101-1,4.16 Step 1 : -55 -30 C, 30 3 min. Step 2 : 25 +10 -5 C, 3 min. max. Step 3 : 125 +30 C, 30 3 min. Step 4 : 25 +10 -5 C, 3 min. max. Number of cycles : 5 MIL-STD-202 method 104A Temperature of hot bath of fresh water: 65 +50 C Temperature of saturated solution of sodium chloride and water: 03C Duration of immersion: 15 2 min. Number of cycle: 2 JIS C 60068-2-38 High temperature : 65 +50 C 90 to 98%R.H. Low temperature : 25 -20 C 90 to 98%R.H. JIS C 60068-2-11 Temperature : 35 2C Salt solution : 51% (wt) Duration : 484 h JIS C 5101-1,4.23 Test temperature and applied voltage : 85 2C and rated voltage or 125 3C and 2/3 x rated voltage Duration : 2000 +72 0 h Power supply impedance : 3 or less FREQUENCY CHARACTERISTICS 112M 35VDC-15mF H-case , Sample:5pcs Measuring temperature : room temperature 10K 1K Imp.() Impedance & ESR() 100 10 1 E.S.R.() 0.1 0.01 0.00 100 1K 10K 100K 10M 1M TEMPERATURE CHARACTERISTICS 112M 16VDC-330mF D-case, Sample:12pcs. 14 12 mean 8 1000 6 4 2 100 0 -2 -4 -6 -8 -10 -12 -60 -40 -20 0 20 40 60 80 100 120 Leakage current Capacitance change 10 10 1 Dissipation factor Temperature() 0.10 0.08 0.1 0.06 0.04 0.02 0.00 0.01 -60 -40 -20 0 20 40 60 80 Temperature() 100 120 0 20 40 60 80 100 120 Temperature() 6 ENDURANCE 85, RATED VOLTAGE Capacitance hange (%) Dissipation factor 112M 10VDC-47mF B-Case, Sample : 50pcs 2 1 0 -1 -2 -3 -4 -5 0.1 0.08 0.06 0.04 0.02 0 Max. mean Min. Max. mean Min. Leakage current (A) 1000 100 10 1 0.1 0.01 1 INITIAL VALUE 10 100 1000 10000 Capacitanc e 4 2 0 -2 -4 -6 -8 -10 Dissipation factor Time (Hours) 0.1 0.08 0.06 0.04 0.02 0 112M 16VDC-330mF D-Case, Sample : 50pcs Leakage current (A) 10000 1000 100 10 1 0.1 1 INITIAL VALUE 10 10 100 Time (Hours) 7 1000 10000 Application Notes for Tantalum Solid Electrolytic Capacitor Hermetically sealed capacitors in metal case 1. Operating Voltage Tantalum Solid Electrolytic Capacitor shall be operated at the rated voltage or lower. Rated voltage: The "rated voltage" refers to the maximum DC voltage that is allowed to be continuously applied between the capacitor terminals at the rated temperature. Surge voltage: The "surge voltage" refers to the voltage that is allowed to be instantaneously applied to the capacitor at the rated temperature or the maximum working temperature. The capacitor shall withstand the voltage when a 30-second cycle of application of the voltage through a 1000 series resistance is repeated 1000 times in 6-minute periods. Rated voltage (VDC) Surge voltage (VDC) 6.3 8 10 13 16 20 20 25 25 32 35 44 50 63 When designing the circuit, the equipment's required reliability must be considered and appropriate voltage derating must be performed. Figure 1 shows the recommended voltage derating curve for Tantalum capacitors as described by NASA APPLICATION NOTES. Voltage derating factor Fig-1 Voltage Derating Curve (Recommended) 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -55 -35 -15 5 25 45 65 85 105 125 Ambient temperature () 2. Application that contain AC Voltage Special attention to the following 3 items. (1) The sum of the DC bias voltage and the positive peak value of the AC voltage should not exceed the rated voltage. (2) Reverse voltage should not exceed the allowable values of the negative peak AC voltage. (3) Ripple current should not exceed the allowable values. 3. Reverse Voltage Tantalum solid electrolytic capacitor is polarity. Please do not impress reverse voltage. As well, please confirm the potential of the tester beforehand when both ends of the capacitor are checked with the tester etc. 4. Permissible Ripple Voltage Permissible ripple voltage is determined by the heat loss of the element and heat radiation of the lead wire. This is influenced by capacitance, ESR, operating temperature, and frequency or ripple. Please consult Matsuo's Engineering Bulletin for details on calculating ripple current values. 5. Application on low-impedance circuit The failure rate of low impedance circuit at 0.1/V is about five times greater than that of a 1/V circuit. To curtail this higher failure rate, tantalum capacitors used in low impedance circuits, such as filters for power supplies, particularly switching power supplies, or for noise by-passing, require that operating voltage be derated to less than half of the rated voltage. Actually, less than 1/3 of the rated voltage is recommended. 6. Non Polar Application(BACK TO BACK) Tantalum capacitors can be used as a non-polar unit if two capacitors are connected "BACK-TO-BACK" when reserve voltage is applied at a more than permissible value, or in a purely AC circuit. The two capacitors should both be of the same rated voltage and capacitance tolerance, and they should both be twice the required capacitance value. Fig-2 + + Ripple Voltage: Permissible Ripple Voltage shall not exceed the value allowed for either C1 or C2 (This will be the same, as the capacitors should be identical.) A B C1 C2 Capacitance: (C1 x C2) / (C1 + C2) Leakage Current: If terminal A is (+), the Leakage Current will be equal to C1's Leakage Current. If terminal B is (+), the Leakage Current will be equal to C2's Leakage Current. 7. Soldering The soldering of Type 112 should be operated per the following recommended conditions. (1) Flow Soldering (Direct heating from the substrate) Solder temperature: 260C or less Dipping time: 10 s Note1: Noted that solder part of hermetic could be melted If soldering temperature is too high or dipping time is too long for the operation. Fig-2 Temperature of Solder Bath() (2) Soldering with a Soldering Iron 280 270 260 250 240 230 220 210 200 0 1 2 3 4 5 6 7 8 9 10 Heating Time (sec) Note2: Please be noted that soldering should be done more than 4mm apart from product body. 8.Example of trouble phenomenon happening by excessive heating when soldering When mounting, the following breakdown phenomena might be caused when excessive heating that exceeds the above-mentioned tolerance is done. Therefore, please pay attention to the operation. In a case that solder is used for cathode connection of molding type product, Ag in silver paste could merge into solder if solder in product have melted. That might cause excessive Leakage Current and Short etc. by changing in deterioration in DF and the high frequency impedance or internal stresses in that case. Mechanical stress according to heat stress and expansion shrinkage or concentrations of internal stress might increase failure rate. Defect sealing could sometimes come for solder melting in seal entrance part of Type 112. Or, solder flows, might become a bridge between inside and outside circles of the Hermetic seal, be good at the solder grain if inhaled, and the phenomenon such as a short or intermittent shorts be caused. 8 9.Flux Please use flux as much as possible with non-acidity and little content of both chlorine and amine. 10. Cleaning Cleaning by organic solvent may damage capacitor's appearance and performance. However, our capacitors are not effected even when soaked at 20 ~ 30C 2-propanol for 5 minutes. When introducing new cleaning methods or changing the cleaning term, please consult us. 11. Protective Resin Coating After components are assembled to substrate, a protective resin coating is sometimes applied. As this resin coating cures, it gives mechanical and thermal stress to Tantalum capacitors. This stress can cause damage to the capacitors, which affects their reliability. Before using a resin coating, proper research must be done in regards to the material and process to insure that excessive stress will not be applied to capacitors and other components. 12. Vibration Approximately 300 G shall be applied to a capacitor, when dropped from 1 meter to a concrete floor. Although capacitors are made to withstand this drop test, stress from shock due to falling or striking does cause damage to the capacitors and increases failure rates. Do not subject capacitors to this type of mechanical stress. 13. Additional Notes * When more than one capacitor is connected in series, a resistor that can distribute the voltage equally to the capacitors shall be connected in parallel. * The capacitor cases shall not be cut even if the mounting space is insufficient. * Do not process lead wire terminal in a way other than cutting or bending the part that projects from printed circuit board (plated through hole). * Do not add the outside power more than regulations to lead wire terminal. Do not add excessive power to capacitor. * During a customers aging process, voltage should remain under the rated voltage at all times. * Capacitors should never be touched or manipulated while operating. * Capacitors are not meant to be dismantled. * When testing capacitors, please examine the power source before conducting test to insure the tester's polarity and applied voltage. * Do not touch terminals of other parts if electrode is applied and checked while energizing. Do not bend the lead wire terminal with the electrode testers. * In the event of a capacitor burning, smoking, or emitting an offensive smell during operation, please turn the circuit "off" and keep hands and face away from the burning capacitor. * If a capacitor be electrical shorted, it becomes hot, and the capacitor element may ignite. In this case, the printed board may be burnt out. * A for capacitors (Type 112) with the metal casing, pressure in the cases might go up by Short before they explode, and then high-temperature solder might disperse. * Capacitors should be stored at room temperature under low humidity. Capacitors should never be stored under direct sunlight, and should be stored in an environment containing dust. * If the capacitors will be operated in a humid environment, they should be sealed with a compound under proper conditions. * Capacitors should not be stored or operated in environments containing acids, alkalis or active gasses. * When capacitors are disposed of as "scrap" or waste, they should be treated as Industria Waste since they contain various metals and polymers. * Capacitors submitted as samples should not be used for production purposes. These application notes are prepared based on "Guideline of notabilia for fixed tantalum electrolytic capacitors with solid electrolyte for use in electronic equipment" (EIAJ RCR-2368) issued by Japan Electronics and Information Technology Industries Association (JEITA). For the details of the instructions (explanation, reasons and concrete examples), please refer to this guideline, or consult our Sales Department. R MATSUO MATSUO ELECTRIC CO., LTD. Pleas e f eel f ree t o as k o ur Sales D ep art ment f o r mo re inf ormation o n Tant alum So lid Elec t roly tic Cap ac it o r . Overseas Sales Dep. Head office URL 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0883 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0871 http://www.ncc-matsuo.co.jp/ Fax : 06-6332-0920 Fax : 06-6331-1386 Specifications on this catalog are subject to change without prior notice. Please inquire of our Sales Department to confirm specifications prior to use. 9