P2811A/B and P2812A/B and P2814A/B Low Power EMI Reduction IC Features * FCC approved method of EMI attenuation * Provides up to 15dB EMI reduction * Generates a 1x, 2x and 4x low EMI spread spectrum clock of the input frequency o 1x: P2811A/B o 2x: P2812A/B o 4x: P2814A/B * Optimized for input frequency range from 10MHz to 40MHz * Internal loop filter minimizes external components and board space * Selectable spread options: o Down Spread and Center Spread * 8 frequency deviation selections: o 0.625% to -3.5% * Low inherent Cycle-to-Cycle Jitter * 3.3V Operating Voltage * CMOS/TTL compatible inputs and outputs. * Pin-out compatible with Cypress CY25811, CY25812 and CY25814 * Available in 8-pin SOIC Package combinations of spread options and percentage deviations. Refer to Frequency Deviation and Spread Selection Table. These combinations include Down and Center Spread, and percentage deviation range from 0.625% to -3.5%. The P28XX reduces electromagnetic interference (EMI) at the clock source, allowing system wide reduction of EMI of downstream clock and data dependent signals. The P28XX allows significant system cost savings by reducing the number of circuit board layers, ferrite beads, shielding, and other passive components that are traditionally required to pass EMI regulations. The P28XX modulates the output of a single PLL in order to "spread" the bandwidth of a synthesized clock, and more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal's bandwidth is called `spread spectrum clock generation'. The P28XX uses the most efficient and optimized modulation profile approved by the FCC and is implemented in a proprietary all-digital method. Product Description The P28XX devices are versatile spread spectrum frequency modulators designed specifically for a wide range of input clock frequencies from 10MHz to 40MHz. Refer to Input/output Frequency Range Selection Table. The P28XX can generate an EMI reduced clock from crystal, ceramic resonator, or system clock. The P28XX-A and the P28XX-B offer various (c)2010 SCILLC. All rights reserved. JUNE 2011 - Rev. 2 Applications The P28XX is targeted towards EMI management for memory and LVDS interfaces in mobile graphic chipsets and high-speed digital applications such as PC peripheral devices, consumer electronics, and embedded controller systems. Publication Order Number: P2811/D P2811A/B and P2812A/B and P2814A/B Block Diagram VDD D_C SRS FRS PLL Modulation XIN / CLKIN Crystal Oscillator Frequency Divider XOUT Feedback Divider r Phase Detector Loop Filter VCO Output Divider ModOUT VSS Pin Configuration XIN / CLKIN 1 VSS 2 D_C 3 P2811A/B P2812A/B P2814A/B SRS 4 8 XOUT 7 VDD 6 FRS 5 ModOUT Pin Description Pin# Pin Name Type 1 XIN / CLKIN I 2 VSS P Description Crystal connection or external Clock input. Ground to entire chip. Digital logic input used to select Down (LOW) or Center (HIGH) spread options. (Refer to Frequency Deviation and Spread Selection Table). This pin has an internal pull-up resistor. Spread range select. Digital logic input used to select frequency deviation (Refer to Frequency Deviation and Spread Selection Table). This pin has an internal pull-up resistor. 3 D_C I 4 SRS I 5 ModOUT O Spread spectrum clock output. 6 FRS I Frequency range select. Digital logic input used to select Input frequency range (Refer to Input/Output Frequency Range Selection Table). This pin has an internal pull-up resistor. 7 VDD P Power supply for the entire chip. 8 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. . Rev. 2 | Page 2 of 6 | www.onsemi.com P2811A/B and P2812A/B and P2814A/B Input/Output Frequency Range Selection Table Part Number FRS (pin 6) P2811 (1x) P2812 (2x) P2814 (4x) Modulation Rate Input (MHz) Output (MHz) Input (MHz) Output (MHz) Input (MHz) Output (MHz) 0 10-20 10-20 10-20 20-40 10-20 40-80 Input Frequency / 448 1 20-40 20-40 20-40 40-80 20-40 80-160 Input Frequency / 896 Output Frequency Deviation and Spread Selection Table 1 Frequency Deviation (%) Part Number P28XXA P28XXB D_C (pin 3) SRS (pin 4) FS=0 FS=1 10/20/40 (MHz) 20/40/80 (MHz) 20/40/80 (MHz) 40/80/160 (MHz) 0 0 -3 -2.5 -2.7 -2.6 0 1 -3.7 -3.4 -3.8 -3.6 1 0 1.5 1.2 1.5 1.3 1 1 1.8 1.6 1.9 1.8 0 0 -1.7 -1.0 -1.5 -1.4 0 1 -2.0 -1.5 -2.0 -1.9 1 0 0.75 0.6 0.8 0.7 1 1 1.0 0.75 1.0 0.9 Note: 1. Frequency Deviation given in the table is for the Output Frequency Range covering P2811x / 12x / 14x. Absolute Maximum Ratings Symbol VDD, VIN TSTG Parameter Rating Unit Voltage on any pin with respect to Ground -0.5 to +4.6 V Storage temperature -65 to +125 C Ts Max. Soldering Temperature (10 sec) 260 C TJ Junction Temperature 150 C TDV Static Discharge Voltage(As per JEDEC STD 22- A114-B) 2 KV Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. . Rev. 2 | Page 3 of 6 | www.onsemi.com P2811A/B and P2812A/B and P2814A/B Operating Conditions Symbol Min Max Unit Supply Voltage 3.0 3.6 V TA Operating temperature -40 +85 C CL Load Capacitance 15 pF CIN Input Capacitance 7 pF Max Unit VSS - 0.3 0.8 V 2 VDD + 0.3 V -50 A 50 A 3 mA 3 mA 0.4 V VDD Parameter DC Electrical Characteristics Symbol Parameter Min VIL Input low voltage VIH Input high voltage Input low current (Inputs D_C, SRS and FRS are pulled high internally) IIL IIH Typ Input high current IXOL IXOH XOUT Output low current (VXOL@ 0.4V, VDD = 3.3V) XOUT Output high current (VXOH@ 2.5V, VDD = 3.3V) VOL Output low voltage (VDD = 3.3V, IOL = 15mA) VOH Output high voltage (VDD = 3.3V, IOH = -15mA) ICC Dynamic supply current (Unloaded Output) IDD Static supply current , Standby mode (CLKIN pulled to GND) VDD tON ZOUT Operating voltage 2.5 V 8 3.0 3.3 Power up time (first locked clock cycle after power up) Clock out impedance 24 mA 4.5 mA 3.6 V 500 S 26 AC Electrical Characteristics Symbol fIN fOUT 1 tLH tHL 1 Parameter Min Typ Max Unit Input frequency for P2811/12/13/14 A/B 10 40 MHz Output frequency for P2811A/B 10 40 MHz Output frequency for P2812A/B 20 80 MHz Output frequency for P2814A/B 40 160 MHz Output rise time (measured at 0.8V to 2.0V) 0.4 0.5 0.7 nS Output fall time (measured at 2.0V to 0.8V) 0.5 0.6 0.8 nS tJC Cycle-to-Cycle Jitter (Unloaded Output) tD Output duty cycle 250 45 Note: 1. tLH and tHL are measured into a capacitive load of 15pF . Rev. 2 | Page 4 of 6 | www.onsemi.com 50 pS 55 % P2811A/B and P2812A/B and P2814A/B Package Information 8-Pin SOIC Package H E D A2 A C D e A1 L B Dimensions Symbol Inches Min Max Millimeters Min Max A1 0.004 0.010 0.10 0.25 A 0.053 0.069 1.35 1.75 A2 0.049 0.059 1.25 1.50 B 0.012 0.020 0.31 0.51 C 0.007 0.010 0.18 0.25 D 0.193 BSC 4.90 BSC E 0.154 BSC 3.91 BSC e 0.050 BSC 1.27 BSC H 0.236 BSC 6.00 BSC L 0.016 0.050 0 8 0.41 1.27 0 8 Note: Controlling dimensions are millimeters. SOIC: 0.074 grams unit weight. . Rev. 2 | Page 5 of 6 | www.onsemi.com P2811A/B and P2812A/B and P2814A/B Ordering Code Part Number Marking Package Type Temperature P2811BF-08SR ABU 8-Pin SOIC, Tape & Reel, Pb free 0C to +70C I2811BF-08SR ABV 8-Pin SOIC, Tape & Reel, Pb free -40C to +85C P2814BG-08SR ACD 8-Pin SOIC, Tape & Reel, Pb free 0C to +70C A "microdot" placed at the end of last row of marking or just below the last row toward the center of package indicates Pb-free Licensed under US patent #5,488,627, #6,646,463 and #5,631,920. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. U.S Patent Pending; Timing-Safe and Active Bead are trademarks of PulseCore Semiconductor, a wholly owned subsidiary of ON Semiconductor. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 . Rev. 2 | Page 6 of 6 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative