RKJXK ThumbPointerTMStick Controller RKJXV Compact size, standard type. Also available with lever return mechanism Typical SpecificationsPotentiometer Items RKJXK Rated power RKJXV 0.0125W Maximum operating voltage 50V AC, 5V DC Operating angle 606 23max. in each direction Operating force 8mNm max. Not lever return type 64mNm Lever return type 1410mNm 100,000 cycles 2,000,000 cycles Operating life Multi Control Devices Note If the lever is tilted more than 23from the vertical position, operating feel irregularities or return mechanism errors may occur. Therefore, please do not tilt more than 23. Typical SpecificationsCenter-push Items RKJXK Variable Resistor Type Ratingsmax. RKJXV 50mA 12V DC Operating force 5.22.6N 0.5 Travel Switch Type Operating life 7.43N 0.5 0.5 -0.4 mm 0.4 -0.3 mm 100,000 cycles 500,000 cycles Product Line Product No. RKJXK122400Y Lever return mechanism RKJXV1224005 Total resistance k Resistance taper Minimum order unitpcs. Drawing No. Japan Export 1 With With RKJXK122000D RKJXK1210002 Center-push 500 1,000 Without 2 10 Without B 0B With 3 With RKJXV1220001 1,420 Without 1,420 4 Packing Specifications Tray Product No. 428 Number of packagespcs. 1 case / Japan 1 case / export packing Export package measurementsmm RKJXK 500 1,000 540x373x225 RKJXV 1,420 1,420 544x364x178 Refer to P.433 for soldering conditions. RKJXK/RKJXVThumbPointerTMStick Controller Dimensions No. Unit:mm Photo PC board mounting hole dimensions Viewed from mounting side Style RKJXK1224 25.4 .9 o7 16 a b 3.1 13.3 5 c 7.7 d 4-1.35 1 Square hole Prohibited wiring area 3.7 2.5 7.3 12.9 19.3 le ho Multi Control Devices .5 o1 4- 4.5 o2 8.25 Return position 9 2.6 5-o All directions 60 6 1 1 2 3 VR1 2 hole 6-o1 d c SW1 15.5 9 5 20.7 VR2 16 b a 1 2 3 .9 o7 3.1 9 .6 4-o2 Return position o2 hole 13.3 2 6-o1 5 All directions Switch Type VR1 60 2 9 5 1 2 3 VR2 15.5 Variable Resistor Type 22.7 16 16 20.7 RKJXK1210 RKJXK1220 ole .5 h Prohibited wiring area 3.7 2.5 7.3 12.9 19.3 4-o1 1 2 3 RKJXV1224 17.8 13.15 VR1 O1 .6 12.65 7 5 ho le ho le ho O le 3 18.95 12.45 10.8 2.9 2.6 ho le 4- O Any direction 1. 2 3 4- O 2 1 Height of boss 11.2 2 1 a c b d 4 4.5 SW1 8 Lever return position 6 d 2. 21.3 13.15 .5 c a b 46 max. 3 2- O1 8.73 O1 VR2 5 7 10 6- 2.2 6.5 7 8.6 O3 .5 8.73 Prohibited wiring area 0.75 2.5 429 RKJXK ThumbPointerTMStick Controller RKJXV Dimensions No. Unit:mm Photo PC board mounting hole dimensions Viewed from mounting side Style RKJXV1220 17.8 13.15 8.73 O4 le 8 18.95 12.45 10.8 2.6 Any direction 6 2.9 4 2. Multi Control Devices Lever return position 2.2 7 Variable Resistor Type 11.2 3 .5 8.6 3 2 1 8.73 Height of boss Switch Type 430 le ho 12.65 7 5 7 VR1 21.3 13.15 2- 1.6 ole ho 3 2 1 46 max. 4 1 .5 10 VR2 5 6- 1h 0.75 Prohibited wiring area Multi Control Devices List of Varieties Potentiometer type Type RKJXK RKJXV RKJXY W 20.7 17.8 19.6 18.6 D 25.4 21.3 18.1 24.3 H 12.9 11.2 4.9 5.2 Series RKJXU Photo Dimensions typical value mm Number ofoperating shafts Shaft material Single-shaft Metal Resin Multi Control Devices Directional resolution Continuous Directional operating feeling tactile feeling Without Lever return mechanism With / Without With With / Without Center-push switch Without Without Encoder -10 to 70 Operating temperature range Variable Resistor Type Operating life Directional operation 100,000 cycles 2,000,000 cycles Center-push 100,000 cycles 500,000 cycles Automotive use 1,000,000 cycles 2,000,000 cycles Life cycle (availability) Switch Type Electrical performance Mechanical performance Insulation resistance 100M min. 250V DC Voltage proof 250V AC for 1 minute Slider noise 8mNm max. Without Lever return mechanism 64mNm With Lever return mechanism 1410mNm With knob type 0.430.25N (3.332.0mNm) Without knob type 3.332.0mNm Push operating force 5.22.6N 7.43N Lever return precision Actuator strength Environmental performance 300mV p-p max. by JIS method Directional operating force Push / pull directions Operating direction 0.1mm 98N min.Push,50N min.Pull 100N min.Push,49N min.Pull100N min.Push,30N min.Pull 0.3Nm 50N Cold -30 96h Dry heat 80 96h Damp heat 60, 90 to 95RH 96h Page 5 50N min.Push/Pull 0.750.3N 428 431 432 Variable Resistor Type Multi Control Devices Soldering Conditions 433 Variable Resistor Type Multi Control Devices Cautions 433 424 Potentiometer Type / Soldering Conditions Reference for Manual Soldering Series Tip temperature Soldering time No. of solders 350max. 3s max. 1 time RKJXK, RKJXV Reference for Dip Soldering Series Preheating Heating time Soldering surface temperature Dip soldering Soldering temperature Soldering time No. of solders RKJXK 90 to 100 45s max. 255 to 260 2 to 3s 1 time RKJXV 90 to 120 60s max. 260 5s 1 time Potentiometer Type / Cautions 3 Fig.A.Voltage divider type We recommend you use the potentiometer type in a voltage divider type as shown in Fig. A. 3 2 V V 1 Impedance on the Output Side p [Fig.1] 3 3 2 A/D 3 2 A/D 2 1 1 p p 1 [Fig.2] p A/D 1 p p p p Switch Type Dew Condensation Avoid using the product when condensation or drops of water might occur inside the product. Otherwise, insulation deterioration or shorting may occur. Soldering Do not employ wiring designs and soldering methods as illustrated in the schematic drawing. Molten solder flowing over the upper surface of PC board can cause imperfect contacts. Solder all metal inserted fixing including terminals & metal lugs into a substrate. A/D Variable Resistor Type Since this pot is designed to use with its output is 3 connected directly to A /D port. lmpedance is considered to be mega ohm level. Then contact resistance in the pot 2 is higher. Please refer to Flg-1. So when you use it in the circuit like Flg-2.Please make sure that impedance should 1be over than 1M-ohm. Multi Control Devices Circuit Used for Analog Stick Controller Terminal Solder Solder PC board Stress Being Applied to the Terminals Always be careful not to apply excessive stress on the terminals. Design appropriate soldering conditions. Handling of Variable Resistors Equipped with Switches Exercise care when packing or storing. Packaging or storing while load is applied to the shaft may cause a malfunction in performance. Storage Store the products as delivered, at a normal temperature and humidity, without direct sunshine and corrosive gas ambient. Use them at an earliest possible timing, not later than six months upon receipt. After breaking the seal, keep the products in a plastic bag to shut out ambient air, store them in the same environment as above, and use them up as soon as possible. Do not stack too many switches. The above operation notes are quoted from the "Precaution and Guideline of Potentiometer for Electrical Devices", a technical report issued by the Japan Electronics and Information Technology Industries Association EIAJ RCR-2191Ain March 2002. For details, refer to the original technical report. 433