Order Now Product Folder Support & Community Tools & Software Technical Documents Reference Design ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 ATL431, ATL432 2.5-V Low Iq Adjustable Precision Shunt Regulator 1 Features 3 Description * * The ATL431 and ATL432 are three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and industrial temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5 V) and 36 V, with two external resistors. These devices have a typical output impedance of 0.05 . Active output circuitry provides a very sharp turn-on characteristic, making these devices excellent replacements for Zener diodes in many applications, such as onboard regulation, adjustable power supplies, and switching power supplies. 1 * * * * * Adjustable Regulated Output of 2.5 V to 36 V Very-Low Operating Current - IKA(min) = 35 A (Max) - IREF = 150 nA (Max) Internally Compensated for Stability - Stable With No Capacitive Load Reference Voltage Tolerances at 25C - 0.5% for B Grade - 1% for A Grade Typical Temperature Drift - 5 mV (-40C to +85C); I Version - 6 mV (-40C to +125C); Q Version Extended Cathode Current Range 35 A to 100 mA Low Output Impedance of 0.3 (Max) 2 Applications * * * * * * Secondary Side Regulation in Flyback SMPSs Industrial, Computing, Consumer, and Portables Adjustable Voltage and Current Referencing Power Management Power Isolation Zener Replacement The ATL43x has > 20x improvement cathode current range over it's TL43x predecessor. It also is stable with a wider range of load capacitance types and values. ATL431 and ATL432 are the exact same parts but with different pinouts and order numbers. The ATL43x is offered in two grades, with initial tolerances (at 25C) of 0.5%, 1%, for the B and A grade, respectively. In addition, low output drift vs temperature ensures consistent voltage regulation over the entire temperature range. The ATL43xxI devices are characterized for operation from -40C to +85C, and the ATL43xxQ devices are characterized for operation from -40C to +125C. Device Information(1) PART NUMBER ATL431 ATL432 PACKAGE SOT (3) BODY SIZE (NOM) 2.90 mm x 1.60 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Simplified Schematic Stability Region for VKA = 15.0 V 2000 VKA Input IKA IKA(PA) Vref 1000 STABLE 100 20 0.0001 0.001 0.01 0.1 CKA(PF) 1 10 D001 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 6.7 3 3 3 4 4 4 5 Absolute Maximum Ratings ..................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics, ATL431Ax, ATL432Ax ..... Electrical Characteristics, ATL431Bx, ATL432Bx ..... Typical Characteristics .............................................. Parameter Measurement Information .................. 9 Detailed Description ............................................ 11 8.1 Overview ................................................................. 11 8.2 Functional Block Diagram ....................................... 11 8.3 Feature Description................................................. 11 8.4 Device Functional Modes........................................ 12 9 Application and Implementation ........................ 13 9.1 Application Information............................................ 13 9.2 Typical Applications ................................................ 14 10 Power Supply Recommendations ..................... 18 11 Layout................................................................... 18 11.1 Layout Guidelines ................................................. 18 11.2 Layout Example .................................................... 18 12 Device and Documentation Support ................. 19 12.1 12.2 12.3 12.4 12.5 12.6 Related Links ........................................................ Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 19 19 19 19 19 19 13 Mechanical, Packaging, and Orderable Information ........................................................... 19 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (September 2015) to Revision D Page * Changed Small-Signal Voltage Amplification vs Frequency with an updated graph to provide additional data .................... 6 * Changed Test Circuit for Phase and Gain Measurement with an updated schematic........................................................... 9 * Updated Comparator Mode specifications in Design Parameters........................................................................................ 14 * Added Receiving Notification of Documentation Updates section ....................................................................................... 19 Changes from Revision B (May 2015) to Revision C * Page Changed ATL432xx status from PREVIEW to PRODUCTION. ............................................................................................. 1 Changes from Revision A (April 2015) to Revision B Page * Changed ATL431AQ, ATL431BI and ATL431BQ status from PREVIEW to PRODUCTION. ............................................... 1 * Changed flyback schematic to represent a more robust design ......................................................................................... 13 * Added flyback supply reliability recommendation................................................................................................................. 18 Changes from Original (March 2013) to Revision A * 2 Page Initial release of full verison. ................................................................................................................................................... 1 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 5 Pin Configuration and Functions ATL431 DBZ Package 3-Pin SOT-23 Top View CATHODE ATL432 DBZ Package 3-Pin SOT-23 Top View 1 REF 3 REF 1 ANODE 3 2 CATHODE ANODE 2 Not to scale Not to scale Pin Functions PIN NO. NAME I/O DESCRIPTION ATL431x ATL432x CATHODE 1 2 I/O REF 2 1 I Threshold relative to common anode ANODE 3 3 O Common pin, normally connected to ground Shunt Current/Voltage input 6 Specifications 6.1 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX 40 V 150 mA (2) UNIT VKA Cathode voltage IKA Continuous cathode current -100 II(ref) Reference input current -0.05 10 mA TJ Operating virtual junction temperature -40 150 C Tstg Storage temperature -65 150 C (1) (2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to ANODE, unless otherwise noted. 6.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 2000 Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) 1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions MIN MAX VKA Cathode voltage Vref 36 V IKA Cathode current .035 100 mA TA Operating free-air temperature "I" Grade -40 85 "Q" Grade -40 125 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 UNIT C 3 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com 6.4 Thermal Information ATL43xx THERMAL METRIC (1) DBZ (SOT-23) UNIT 3 PINS RJA Junction-to-ambient thermal resistance 331.8 C/W RJC(top) Junction-to-case (top) thermal resistance 106.5 C/W RJB Junction-to-board thermal resistance 64.6 C/W JT Junction-to-top characterization parameter 4.9 C/W JB Junction-to-board characterization parameter 62.9 C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. 6.5 Electrical Characteristics, ATL431Ax, ATL432Ax over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER Vref Reference voltage TEST CIRCUIT Figure 22 TEST CONDITIONS MIN TYP MAX UNIT 2475 2500 2525 mV ATL43xAI; TA = -40C to 85C 5 15 ATL43xAQ; TA = -40C to 125C 6 34 VKA = 10 V - Vref -0.4 -2.7 VKA = 36 V - 10 V -0.1 -2 VKA = Vref, IKA = 1 mA Deviation of reference input voltage over full temperature range, see section Figure 22 Ratio of change in reference Vref / VKA voltage to the change in cathode voltage Figure 23 IKA = 1 mA Iref Reference input current Figure 23 IKA = 1 mA, R1 = 10 k, R2 = 30 150 nA II(dev) Deviation of reference input current over full temperature range, see section Figure 23 IKA = 1 mA, R1 = 10 k, R2 = 20 50 nA Imin Minimum cathode current for regulation Figure 22 Figure 5 VKA = Vref 20 35 A Ioff Off-state cathode current Figure 24 VKA = 36 V, Vref = 0 0.05 0.2 A |zKA| Dynamic impedance, see section Figure 22 VKA = Vref, f 1 kHz, IKA = 1 mA to 100 mA 0.05 0.3 VI(dev) VKA = Vref, IKA = 1 mA, mV mV/V 6.6 Electrical Characteristics, ATL431Bx, ATL432Bx over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER MIN TYP MAX UNIT 2487 2500 2512 mV ATL43xBI; TA = -40C to 85C 5 15 ATL43xBQ; TA = -40C to 125C 6 34 VKA = 10 V - Vref -0.4 -2.7 VKA = 36 V - 10 V -0.1 -2 IKA = 1 mA, R1 = 10 k, R2 = 30 150 nA Figure 23 IKA = 1 mA, R1 = 10 k, R2 = 20 50 nA Minimum cathode current for regulation Figure 22 Figure 5 VKA = Vref 20 35 A Ioff Off-state cathode current Figure 24 VKA = 36 V, Vref = 0 0.05 0.2 A |zKA| Dynamic impedance, see section Figure 22 VKA = Vref, f 1 kHz, IKA = 1 mA to 100 mA 0.05 0.3 Vref Reference voltage VI(dev) TEST CIRCUIT TEST CONDITIONS Figure 22 VKA = Vref, IKA = 1 mA Deviation of reference input voltage over full temperature range, see section Figure 22 VKA = Vref, IKA = 1 mA Vref / VKA Ratio of change in reference voltage to the change in cathode voltage Figure 23 IKA = 1 mA Iref Reference input current Figure 23 II(dev) Deviation of reference input current over full temperature range, see section Imin 4 Submit Documentation Feedback mV mV/V Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 6.7 Typical Characteristics Data at high and low temperatures are applicable only within the recommended operating free-air temperature ranges of the various devices. 0.04 2520 Vref = 2485mV Vref = 2500mV Vref = 2504mV 2515 2510 0.032 IREF (PA) Vref (mV) 2505 2500 2495 0.024 0.016 2490 2485 0.008 2480 2475 -40 -20 0 20 40 60 TA (qC) 80 100 120 0 -40 140 -20 0 20 40 60 TA (qC) 80 100 120 140 IKA=1mA Figure 2. Reference Current vs Free-Air Temperature Figure 1. Reference Voltage vs Free-Air Temperature 100 40 TA = -40qC TA = 25qC TA = 85qC TA = 125qC 80 60 30 40 IKA (PA) IKA (mA) 20 0 -20 20 -40 10 -60 -80 -100 -1.5 0 -1 -0.5 0 0.5 1 1.5 VKA = VREF (V) 2 2.5 3 0 0.5 1 D001 1.5 2 VKA = VREF (V) 2.5 3 D001 Figure 4. Cathode Current vs Cathode Voltage Figure 3. Cathode Current vs Cathode Voltage 0.2 30 0.16 25 IOFF (PA) IKA (PA) Ik(min) 20 15 10 2.3 0.12 0.08 0.04 2.35 2.4 2.45 VKA = VREF (V) 2.5 2.55 Figure 5. Cathode Current vs Cathode Voltage 0 -40 -20 0 20 40 60 TA (qC) 80 100 120 140 Figure 6. Off-State Cathode Current vs Free-Air Temperature Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 5 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com Typical Characteristics (continued) Data at high and low temperatures are applicable only within the recommended operating free-air temperature ranges of the various devices. -0.1 0 -0.5 -0.15 -1 -0.2 'Vref/'Vka (mV) -1.5 'Vref (mV) -2 -2.5 -3 -3.5 -4 Vref to 10V 10V to 36V -0.25 -0.3 -0.35 -0.4 -4.5 -5 -0.45 -5.5 -0.5 -40 -6 0 5 10 15 20 Vka (V) 25 30 35 40 IKA=1mA -20 0 20 40 60 80 Temperature (qC) 100 140 D001 IKA=1mA Figure 7. Delta Reference Voltage vs Cathode Voltage Figure 8. Delta Reference Voltage vs Cathode Voltage 900 180 Gain Phase 160 Gain (dB) and Phase () 840 Noise (nV/--Hz) 120 780 720 660 140 120 100 80 60 40 20 0 20 600 10 100 1000 Frequency (Hz) 10 10000 100 1000 10000 100000 1000000 Frequency (Hz) D001 IKA = 1 mA C001 Figure 25 used for this measurement. Figure 9. Noise Voltage IKA=1mA Figure 10. Small-Signal Voltage Amplification vs Frequency 0.1 1.2 1.1 0.08 Output Impedance (:) Output Impedance (:) 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.06 0.04 0.02 0.2 0.1 0 100 1000 10000 Frequency (Hz) 100000 1000000 Figure 26 used for this measurement. -20 0 20 40 60 TA (qC) 80 100 120 140 Figure 26 used for this measurement. Figure 11. Output Impedance vs Frequency 6 0 -40 Figure 12. DC Output Impedance vs Temperature Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 Typical Characteristics (continued) Data at high and low temperatures are applicable only within the recommended operating free-air temperature ranges of the various devices. 2000 1000 Unstable IKA(PA) STABLE 100 STABLE 20 0.0001 0.001 ESR < 20 m IKA = 100 A 0.01 0.1 CKA(PF) 1 10 D001 Figure 27 used to verify stability. Figure 28 used for this measurement. Figure 13. Pulse Response Figure 14. Low IKA (VKA = 2.5 V) Stability Boundary Conditions all ATL43xx Devices 2000 2000 1000 1000 Unstable Unstable STABLE IKA(PA) IKA(PA) STABLE 100 100 STABLE 20 0.0001 0.001 ESR < 20 m 0.01 0.1 CKA(PF) 1 STABLE 20 0.0001 10 0.001 D001 Figure 27 used to verify stability. ESR < 20 m Figure 15. Low IKA (VKA = 5.0 V) Stability Boundary Conditions all ATL43xx Devices 0.01 0.1 CKA(PF) 1 10 D001 Figure 27 used to verify stability. Figure 16. Low IKA (VKA = 10.0 V) Stability Boundary Conditions all ATL43xx Devices 100 2000 IKA(mA) IKA(PA) 1000 STABLE Unstable 10 100 Stable 20 0.0001 0.001 ESR < 20m 0.01 0.1 CKA(PF) 1 10 1 0.0001 0.001 D001 Figure 27 used to verify stability. Figure 17. Low IKA (VKA = 15.0 V) Stability Boundary Conditions all ATL43xx Devices ESR < 20 m 0.01 0.1 CKA(uF) 1 10 D001 Figure 27 used to verify stability. Figure 18. High IKA (VKA = 2.5 V) Stability Boundary Conditions all ATL43xx Devices Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 7 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com Typical Characteristics (continued) Data at high and low temperatures are applicable only within the recommended operating free-air temperature ranges of the various devices. 100 100 IKA(mA) IKA(mA) Stable 10 Stable 10 Unstable 1 0.0001 0.001 ESR < 20 m 0.01 0.1 CKA(uF) 1 Unstable 1 0.0001 10 0.001 0.01 0.1 CKA(uF) D001 Figure 27 used to verify stability. ESR < 20 m Figure 19. High IKA (VKA = 5.0 V) Stability Boundary Conditions all ATL43xx Devices 1 10 D001 Figure 27 used to verify stability. Figure 20. High IKA (VKA = 10.0 V) Stability Boundary Conditions all ATL43xx Devices IKA(mA) 100 10 1 0.0001 Stable 0.001 ESR < 20 m 0.01 0.1 CKA(uF) 1 10 D001 Figure 27 used to verify stability. Figure 21. High IKA (VKA = 15.0 V) Stability Boundary Conditions all ATL43xx Devices 8 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 7 Parameter Measurement Information The deviation parameters Vref(dev) and Iref(dev) are defined as the differences between the maximum and minimum values obtained over the rated temperature range. The average full-range temperature coefficient of the reference input voltage Vref is defined as: Vref is positive or negative, depending on whether minimum Vref or maximum Vref, respectively, occurs at the lower temperature. |zKA| = VKA I The dynamic impedance is defined as: When the device is operating with two external resistors (see Figure 23), the total dynamic impedance of the KA circuit is given by: |z'| = V I which is approximately equal to VKA Input ( |zKA| 1 + R1 R2 ( Input VKA IKA IKA Vref R1 Iref R2 Vref Figure 23. Test Circuit for VKA > Vref Figure 22. Test Circuit for VKA = Vref Input R1 o ae VKA = Vref c 1 + / + Iref x R1 R2 o e VKA Ioff IK= 1mA 15 kQ 2.5 k 100 F VDC = 7.57 V 15 kQ Figure 24. Test Circuit for Ioff Figure 25. Test Circuit for Phase and Gain Measurement Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 9 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com Parameter Measurement Information (continued) >250Y 10 F + IK R1 = 10NY + CL - R2 Vbat >250Y IK + Vbat CL - Figure 26. Test Circuit for Reference Impedance (ZKA) Figure 27. Test Circuit for Stability Boundary Conditions 25NY OUTPUT IK Pulse Generator F = 100kHz 50 Y GND Figure 28. Test Circuit for Pulse Response 10 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 8 Detailed Description 8.1 Overview ATL43x is a low power counterpart to TL431 and TLV431, having lower minimum cathode current (Ik(min) = 35 A). Like TL431, ATL43x is used in conjunction with it's key components to behave as a single voltage reference, error amplifier, voltage clamp or comparator with integrated reference. ATL43x can be operated and adjusted to cathode voltages from 2.5 V to 36 V, making this part optimum for a wide range of end equipments in industrial, auto, telecom and computing. In order for this device to behave as a shunt regulator or error amplifier, > 35 A (Imin(max)) must be supplied in to the cathode pin. Under this condition, feedback can be applied from the Cathode and Ref pins to create a replica of the internal reference voltage. Various reference voltage options can be purchased with initial tolerances (at 25C) of 0.5% and 1.0%. These reference options are denoted by B (0.5%) and A (1.0%) after the ATL43x. The ATL43xxI devices are characterized for operation from -40C to +85C, and the ATL43xxQ devices are characterized for operation from -40C to +125C. 8.2 Functional Block Diagram CATHODE REF + Vref ANODE 8.3 Feature Description ATL43x consists of an internal reference and amplifier that outputs a sink current based on the difference between the reference pin and the virtual internal pin. The sink current is produced by an internal Darlington pair. When operated with enough voltage headroom ( 2.5 V) and cathode current (IKA), ATL43x forces the reference pin to 2.5 V. However, the reference pin can not be left floating, as it needs Iref 0.1 A (please see the Functional Block Diagram). This is because the reference pin is driven into an NPN, which needs base current in order operate properly. When feedback is applied from the Cathode and Reference pins, ATL43x behaves as a Zener diode, regulating to a constant voltage dependent on current being supplied into the cathode. This is due to the internal amplifier and reference entering the proper operating regions. The same amount of current needed in the above feedback situation must be applied to this device in open loop, servo or error amplifying implementations in order for it to be in the proper linear region giving ATL43x enough gain. Unlike many linear regulators, ATL43x is internally compensated to be stable without an output capacitor between the cathode and anode; however, if it is desired to use an output capacitor Figure 14 through Figure 21 can be used as a guide to assist in choosing the correct capacitor to maintain stability. Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 11 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com 8.4 Device Functional Modes 8.4.1 Open Loop (Comparator) When the cathode/output voltage or current of ATL43x is not being fed back to the reference/input pin in any form, this device is operating in open loop. With such high gain in this configuration, ATL43x is typically used as a comparator. Due to the integrated reference, the ATL43x allows users to monitor a certain level of a single signal. 8.4.2 Closed Loop When the cathode/output voltage or current of ATL43x is being fed back to the reference/input pin in any form, this device is operating in closed loop. The majority of applications involving ATL43x use it in this manner to regulate a fixed voltage or current. The feedback enables this device to behave as an error amplifier, computing a portion of the output voltage and adjusting it to maintain the desired regulation. This is done by relating the output voltage back to the reference pin in a manner to make it equal to the internal reference voltage, which can be accomplished via resistive or direct feedback. 12 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information Figure 29 shows the ATL43x used in a 24-V isolated flyback supply. The output of the regulator, plus the forward voltage drop of the optocoupler LED (2.5 + 0.7 = 3.2 V), determine the minimum voltage that can be regulated in an isolated supply configuration. Regulated voltage as low as 5.0 Vdc is possible in the topology shown in Figure 29. The 431 family of devices are prevalent in these applications, being designers go-to choice for secondary side regulation. Due to this prevalence, this section will further go on to explain operation and design in both states of ATL43x that this application will see, open loop (Comparator + Vref) and closed loop (Shunt Regulator). ATL43x's key benefit in isolated supplies is the no load power savings gained by the > 20x decrease in IKmin from TL431. More information about this and other benefits can be found in Designing with the "Advanced" TL431, ATL431, SLVA685. Further information about system stability and using a ATL43x device for compensation can be found in Compensation Design With TL431 for UCC28600, SLUA671. VI 120 V Vo=24 V Gate Drive VCC Ibias Controller VFB Current Sense GND ATL431 Figure 29. Flyback With Isolation Using ATL43x as Voltage Reference and Error Amplifier Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 13 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com 9.2 Typical Applications 9.2.1 Comparator With Integrated Reference (Open Loop) Vsup Rsup Vout CATHODE R1 VL RIN REF VIN + R2 2.5V ANODE Figure 30. Comparator Application Schematic 9.2.1.1 Design Requirements For this design example, use the parameters listed in Table 1 as the input parameters. Table 1. Design Parameters DESIGN PARAMETER EXAMPLE VALUE Input voltage range 0 V to 3.3 V Input resistance 100 k Supply voltage 5V Cathode current (IK) 50 A High output voltage level (Vin < 2.5 V) Vsup Low output voltage (Vin > 2.5 V) ~2 V 9.2.1.2 Detailed Design Procedure When using ATL43x as a comparator with reference, determine the following: * Input voltage range * Reference voltage accuracy * Output logic input high and low level thresholds * Current source resistance 9.2.1.2.1 Basic Operation In the configuration shown in Figure 30 ATL43x will behave as a comparator, comparing the Vref pin voltage to the internal virtual reference voltage. When provided a proper cathode current (Ik), ATL43x will have enough open loop gain to provide a quick response. With the ATL43x's max operating current (Imin) being 35 A and up to 40 A over temperature, operation below that could result in low gain, leading to a slow response. 14 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 9.2.1.2.2 Overdrive Slow or inaccurate responses can also occur when the reference pin is not provided enough overdrive voltage. This is the amount of voltage that is higher than the internal virtual reference. The internal virtual reference voltage will be within the range of 2.5 V (0.5% or 1.0%) depending on which version is being used. The more overdrive voltage provided, the faster the ATL43x will respond. For applications where ATL43x is being used as a comparator, it is best to set the trip point to greater than the positive expected error (that is, +1.0% for the A version). For fast response, setting the trip point to > 10% of the internal Vref should suffice. Figure 31 shows the transition from VOH to VOL based on the input voltage and can be used as a guide for selecting the overdrive voltage. For minimal voltage drop or difference from Vin to the ref pin, it is recommended to use an input resistor < 1 M to provide Iref. 9.2.1.2.3 Output Voltage and Logic Input Level In order for ATL43x to properly be used as a comparator, the logic output must be readable by the receiving logic device. This is accomplished by knowing the input high and low level threshold voltage levels, typically denoted by VIH and VIL. As seen in Figure 31, ATL43x's output low level voltage in open-loop/comparator mode is ~2 V, which is sufficient for some 5.0 V supplied logic. However, would not work for 3.3 V and 1.8 V supplied logic. In order to accommodate this, a resistive divider can be tied to the output to attenuate the output voltage to a voltage legible to the receiving low voltage logic device. ATL43x's output high voltage is approximately Vsup due to ATL43x being open-collector. If Vsup is much higher than the receiving logic's maximum input voltage tolerance, the output must be attenuated to accommodate the outgoing logic's reliability. When using a resistive divider on the output, be sure to make the sum of the resistive divider (R1 and R2 in Figure 30) is much greater than Rsup in order to not interfere with ATL43x's ability to pull close to Vsup when turning off. 9.2.1.2.3.1 Input Resistance ATL43x requires an input resistance in this application in order to source the reference current (Iref) needed from this device to be in the proper operating regions while turning on. The actual voltage seen at the ref pin will be: Vref = Vin - Iref x Rin (1) Because Iref can be as high as 0.15 A, TI recommends to use a resistance small enough that will mitigate the error that Iref creates from Vin. Also, the input resistance must be set high enough as to not surpass the absolute maximum of 10 mA. VOUT (V) 9.2.1.3 Application Curve 5.5 5.25 5 4.75 4.5 4.25 4 3.75 3.5 3.25 3 2.75 2.5 2.25 2 1.75 1.5 2 2.1 2.2 2.3 2.4 2.5 2.6 VIN (V) 2.7 2.8 2.9 3 D001 RIN = 100 k VSUP = 5.0 V RSUP = 10 k Figure 31. Open Loop (Comparator Mode) VOUT vs VIN Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 15 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com 9.2.2 Shunt Regulator/Reference RSUP VSUP VO = ( 1 + R1 0.1% R2 ) VREF CATHODE REF VREF R1 R2 0.1% ATL431 CL ANODE Figure 32. Shunt Regulator Schematic 9.2.2.1 Design Requirements For this design example, use the parameters listed in Table 2 as the input parameters. Table 2. Design Parameters DESIGN PARAMETER EXAMPLE VALUE Reference initial accuracy 1.0% Supply voltage 48 V Cathode current (IK) 50 A Output voltage level 2.5 V to 36 V Load capacitance 1 nF Feedback resistor values (R1 and R2) 10 k 9.2.2.2 Detailed Design Procedure When using ATL43x as a Shunt Regulator, determine the following: * Input voltage range * Temperature range * Total accuracy * Cathode current * Reference initial accuracy * Output capacitance 9.2.2.2.1 Programming Output/Cathode Voltage In order to program the cathode voltage to a regulated voltage a resistive bridge must be shunted between the cathode and anode pins with the mid point tied to the reference pin. This can be seen in Figure 32, with R1 and R2 being the resistive bridge. The cathode/output voltage in the shunt regulator configuration can be approximated by the equation shown in Figure 32. The cathode voltage can be more accurately determined by taking in to account the cathode current: VO = (1 + R1 / R2) x Vref - Iref x R1 (2) For this equation to be valid, ATL43x must be fully biased so that it has enough open loop gain to mitigate any gain error. This can be done by meeting the Imin spec denoted in Electrical Characteristics, ATL431Ax, ATL432Ax table. 9.2.2.2.2 Total Accuracy When programming the output above unity gain (VKA = Vref), ATL43x is susceptible to other errors that may effect the overall accuracy beyond Vref. These errors include: * * * 16 R1 and R2 accuracies VI(dev) - Change in reference voltage over temperature Vref / VKA - Change in reference voltage to the change in cathode voltage Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com * SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 |zKA| - Dynamic impedance, causing a change in cathode voltage with cathode current Worst case cathode voltage can be determined taking all of the variables in to account. Setting the Shunt Voltage on an Adjustable Shunt, SLVA445, assists designers in setting the shunt voltage to achieve optimum accuracy for this device. 9.2.2.2.3 Stability Though ATL43x is stable with no capacitive load, the device that receives the shunt regulator's output voltage could present a capacitive load that is within the ATL43x region of stability, shown in Figure 14 through Figure 21. Also, designers may use capacitive loads to improve the transient response or for power supply decoupling. Figure 14 through Figure 21 should be used as a guide for capacitor selection and compensation. It is characterized using ceramic capacitors with very-low ESR. When it is desirable to use a capacitor within the unstable region, higher ESR capacitors can be used to stabilize ATL43x or an external series resistance can be added. For more information and guidance on ESR values, see Designing with the "Advanced" TL431, ATL431, SLVA685. Unlike TL431, the stability boundary is characterized and determined with resistors 250 and greater. Which is more suitable for low cathode current applications. 9.2.2.3 Application Curves Figure 33. ATL43x Start-up Response IKA = 50 A Figure 34. ATL43x Start-up Response IKA = 1 mA Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 17 ATL431, ATL432 SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 www.ti.com 10 Power Supply Recommendations When using ATL43x in a flyback supply (see Figure 29) it is often common for designers to place the bias resistor between the Anode of the Opto-Coupler and the output voltage (VO = 24 V). However, this makes ATL43x more susceptible to EOS/ESD damage. Therefore, TI recommends to place the bias resistor between the Cathodes of the Opto-Coupler and ATL43x, as shown in Figure 29. For further explanation, see Designing with the "Advanced" TL431, ATL431, SLVA685. When using ATL43x as a Linear Regulator to supply a load, designers will typically use a bypass capacitor on the output/cathode pin. Be sure that the capacitance is within the stability criteria shown in Figure 14 through Figure 21. To not exceed the maximum cathode current, be sure that the supply voltage is current limited. Also, be sure to limit the current being driven into the Ref pin, as not to exceed it's absolute maximum rating. For applications shunting high currents, pay attention to the cathode and anode trace lengths, adjusting the width of the traces to have the proper current density. 11 Layout 11.1 Layout Guidelines Place decoupling capacitors as close to the device as possible. Use appropriate widths for traces when shunting high currents to avoid excessive voltage drops. 11.2 Layout Example DBZ (TOP VIEW) Rref Vin REF 1 Rsup Vsup ANODE 3 CATHODE GND 2 CL GND Figure 35. DBZ Layout Example 18 Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 ATL431, ATL432 www.ti.com SLVSCV5D - MARCH 2015 - REVISED OCTOBER 2016 12 Device and Documentation Support 12.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 3. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY ATL431 Click here Click here Click here Click here Click here ATL432 Click here Click here Click here Click here Click here 12.2 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 12.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 12.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 12.5 Electrostatic Discharge Caution This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 12.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright (c) 2015-2016, Texas Instruments Incorporated Product Folder Links: ATL431 ATL432 19 PACKAGE OPTION ADDENDUM www.ti.com 12-Oct-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ATL431AIDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (ZCKS ~ ZCR3) ATL431AQDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (ZCLS ~ ZCS3) ATL431BIDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (ZCMS ~ ZCT3) ATL431BQDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (ZCJS ~ ZCU3) ATL432AIDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (ZCNS ~ ZCV3) ATL432AQDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (ZCOS ~ ZCW3) ATL432BIDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (ZCPS ~ ZCX3) ATL432BQDBZR ACTIVE SOT-23 DBZ 3 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 (ZCQS ~ ZCY3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 12-Oct-2016 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 8-Feb-2018 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) ATL431AIDBZR SOT-23 DBZ 3 3000 178.0 9.2 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.15 2.77 1.22 4.0 8.0 Q3 ATL431AIDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL431AQDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL431AQDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL431BIDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL431BIDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL431BQDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL431BQDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL432AIDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL432AIDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL432AQDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL432AQDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL432BIDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL432BIDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 ATL432BQDBZR SOT-23 DBZ 3 3000 180.0 8.4 3.15 2.77 1.22 4.0 8.0 Q3 ATL432BQDBZR SOT-23 DBZ 3 3000 178.0 9.2 3.15 2.77 1.22 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Feb-2018 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ATL431AIDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL431AIDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL431AQDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL431AQDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL431BIDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL431BIDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL431BQDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL431BQDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL432AIDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL432AIDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL432AQDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL432AQDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL432BIDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL432BIDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 ATL432BQDBZR SOT-23 DBZ 3 3000 183.0 183.0 20.0 ATL432BQDBZR SOT-23 DBZ 3 3000 180.0 180.0 18.0 Pack Materials-Page 2 4203227/C PACKAGE OUTLINE DBZ0003A SOT-23 - 1.12 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 2.64 2.10 1.4 1.2 PIN 1 INDEX AREA 1.12 MAX B A 0.1 C 1 0.95 3.04 2.80 1.9 3X 3 0.5 0.3 0.2 2 (0.95) C A B 0.25 GAGE PLANE 0 -8 TYP 0.10 TYP 0.01 0.20 TYP 0.08 0.6 TYP 0.2 SEATING PLANE 4214838/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Reference JEDEC registration TO-236, except minimum foot length. www.ti.com EXAMPLE BOARD LAYOUT DBZ0003A SOT-23 - 1.12 mm max height SMALL OUTLINE TRANSISTOR PKG 3X (1.3) 1 3X (0.6) SYMM 3 2X (0.95) 2 (R0.05) TYP (2.1) LAND PATTERN EXAMPLE SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214838/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBZ0003A SOT-23 - 1.12 mm max height SMALL OUTLINE TRANSISTOR PKG 3X (1.3) 1 3X (0.6) SYMM 3 2X(0.95) 2 (R0.05) TYP (2.1) SOLDER PASTE EXAMPLE BASED ON 0.125 THICK STENCIL SCALE:15X 4214838/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: ATL431AIDBZR ATL431BIDBZR ATL431BQDBZR ATL431AQDBZR