tyca /cecrones Golden Crimp and Crimp Silver ANP Instruction Sheet 408-8509 (was RF-ASMB-11) Right-Angle Connectors 25SEP01 RevO Fertule Housing Phy iG Insulator mrceee (fl c+) Stide-On-Series Housing Cable / ==!|| Unsealed Subassembly Insulator 2 Pin Contact ---[) [E}-- Fertule Subassembly A . Plug J Screw-On-Series an Unsealed (Knurl Nut Shown) Ferrule Subassembly Plug ; 7 Serew-On-Series Housing iia Sealed Middle Sealing Insulator (Hex Nut Shown} Sleeve Sleeve O-Ring Seal Coaxial Cable Figure 1 INTRODUCTION This instruction sheet covers the assembly procedures for Golden Crimp and Crimp Silver Right-Angle Connectors. See Figure 1. Dimensions on this sheet are in inches [with millimeters in brackets}. Figures and illustrations are for identification only and are not drawn to Extreme care must be taken to avoid nicking or culting shield wires when trimming jacket. CAUTION Note: For assembly to cable with MiniNoise coating, Mini-Noise coating must be removed from surface of cable dielectric as follows: 1. Painted Coatings: Wipe off dielectric surface with a dry cloth. Wipe again using paint thinner or scale. Sealing Middle Sleeve Dielectric Co CAUTION _| Do Not Nick Shield Wires [22.23] NOTE: Not to Seale trichloroethane. Do net immerse cable in solvent. 2. Tape or Fused Coatings: Remove with sandpaper, file, or scraping action of razor blade. Do not damage dielectric. Step 2 To prevent personal injury, use caution when handling file or razor biade. Slide inner sleeve, small end first, over dielectric and under the shield until shield wires are flush with Figure 2 Step 1 Slip sealing sleeve and middle sleeve on cable and strip to dimensions shown in Figure 2. Fan shield slightly, but do not unbraid. shoulder. Trim excess shield if necessary. Slide middle sleeve flush with shoulder of inner sleeve. Slide sealing sleeve until it butts against the middle sleeve as shown in Figure 3. 2001 Tyco Electronics Corporation, Harrisburg, PA. All Intemational Rights Reserved. AMP and Tyco are trademarks. *Trademark This controlled document is subject to change. For latest revision call the AMP FAX* number. TOOLING ASSISTANCE CENTER 1-800-722-1111 1of2 AMP FAX/PRODUCT INFO 1-800-622-6752 For Regional Gustomer Service, visit our website at Loc B www.tycoelectronics.com tyco / Electronics Golden Crimp and Crimp Silver Right-Angle Connectors 408-8509 ANP P P gnreng 550 contact is firmly against the cable insulator. See Trim Shield [13.97] Figure 4. if Necessary Min. ae Inner Sleeve Figure 3 Step 3 Insert assembled components into rear of housing subassembly. Make sure it is properly fitted and in as far as possible. Rotate while pushing to secure a tight fit. See Figure 4. .1154.015 [2.92.38] Pin Contact Housing Insulator Cable Insulator 110 [2.79] Inner Conductor Figure 4 Crimp rear of housing with proper housing crimp tool listed in Figure 5. ELECTRONCS aR KO. aBeris"e | CABLE PART NO. - | PART No. DIA. 415321 29-4 0710-0081-0000 WT-400 .088 [2.24] 4-1532129-5 |010-0082-0000| wr-402 | .110 [2.79] 3-1532136-7 | 010-083-0000] wr7-406 | 155 [3.94] Figure 5 Step 4 Trim dielectric flush with face cf housing subassembly as shown in Figure 4. CAUTION Do not nick inner conductor wires. Step 5 Locate cable insulator over dialectric and press into counterbore of housing subassembly. Trim inner conductor to length shown in Figure 4. Step 6 Locate the pin contact over the inner conductor and press into the cable insulator until the shoulder on the a Product of Astro Tool Corp. Inner conductor must be visible through the inspection hole. Crimp the contact in place with any one of the contact crimp tools listed in Figure 6. TYCO ELECTRONICS MICRODOT MFGS PART NUMBER PART NUMBER | PARTNUMBER Astro Tool 4-1532129-3 010-0065-0000 | \) her st0D1me DANIELS 3-1532136-9 01001340000 #MH7500 (Setting #1) . 001-0104-0000 (Setting #1) 8-1592197-3 (Locator #P79 (Locator) Figure 6 Step 7 Press the housing insulator over the pin contact until seated in place. See Figure 4. Step 8 This applies only for connectors with housing insulator packed ioose. The final stap is to thread and securely tighten the ferrule or ferrule subassembly in place. The recommended torque value is 90-100 inchounces. 115+.015 [2.92+.38] } Ferrule or Ferrule Subassembly Figure 7 Notes: (Unless otherwise specified) Test Voltage 1000 V.R.M.5. Insulation Resistance 5.0 x 109 Ohms Min. REVISION SUMMARY Per EC 0990-0804-01 * |nitial release of instruction sheet Consult manufacturer's literature for current infonnation. 20f2 Rev O