LM4132 LM4132 SOT-23 Precision Low Dropout Voltage Reference Literature Number: SNVS372B LM4132 SOT-23 Precision Low Dropout Voltage Reference General Description Features The LM4132 family of precision voltage references performs comparable to the best laser-trimmed bipolar references, but in cost effective CMOS technology. The key to this break through is the use of EEPROM registers for correction of curvature, tempco, and accuracy on a CMOS bandgap architecture that allows package level programming to overcome assembly shift. The shifts in voltage accuracy and tempco during assembly of die into plastic packages limit the accuracy of references trimmed with laser techniques. Unlike other LDO references, the LM4132 is capable of delivering up to 20mA and does not require an output capacitor or buffer amplifier. These advantages and the SOT23 packaging are important for space-critical applications. Series references provide lower power consumption than shunt references, since they do not have to idle the maximum possible load current under no load conditions. This advantage, the low quiescent current (60A), and the low dropout voltage (400mV) make the LM4132 ideal for batterypowered solutions. n n n n n n n n n n The LM4132 is available in five grades (A, B, C, D and E) for greater flexibility. The best grade devices (A) have an initial accuracy of 0.05% with guaranteed temperature coefficient of 10ppm/C or less, while the lowest grade parts (E) have an initial accuracy of 0.5% and a tempco of 30ppm/C. Output initial voltage accuracy 0.05% Low temperature coefficient 10ppm/C Low Supply Current, 60A Enable pin allowing a 3A shutdown mode 20mA output current Voltage options 1.8V, 2.048V, 2.5V, 3.0V, 3.3V, 4.096V Custom voltage options available (1.8V to 4.096V) VIN range of VREF + 400mV to 5.5V @ 10mA Stable with low ESR ceramic capacitors SOT23-5 Package Applications n n n n n n n n n n n Instrumentation & Process Control Test Equipment Data Acquisition Systems Base Stations Servo Systems Portable, Battery Powered Equipment Automotive & Industrial Precision Regulators Battery Chargers Communications Medical Equipment Typical Application Circuit 20151301 *Note: The capacitor CIN is required and the capacitor COUT is optional. (c) 2006 National Semiconductor Corporation DS201513 www.national.com LM4132 SOT-23 Precision Low Dropout Voltage Reference August 2006 LM4132 Connection Diagram Top View 20151302 SOT23-5 Package NS Package Number MF05A Ordering Information Input Output Voltage Accuracy at 25C And Temperature Coefficient LM4132 Supplied as 1000 units, Tape and Reel LM4132 Supplied as 3000 units, Tape and Reel Part Marking 0.05%, 10 ppm/C max (A grade) LM4132AMF-1.8 LM4132AMFX-1.8 R4AA LM4132AMF-2.0 LM4132AMFX-2.0 R4BA LM4132AMF-2.5 LM4132AMFX-2.5 R4CA LM4132AMF-3.0 LM4132AMFX-3.0 R4DA LM4132AMF-3.3 LM4132AMFX-3.3 R4EA 0.1%, 20 ppm/C max (B grade) 0.2%, 20 ppm/C max (C grade) 0.4%, 20 ppm/C max (D grade) 0.5%, 30 ppm/C max (E grade) LM4132AMF-4.1 LM4132AMFX-4.1 R4FA LM4132BMF-1.8 LM4132BMFX-1.8 R4AB LM4132BMF-2.0 LM4132BMFX-2.0 R4BB LM4132BMF-2.5 LM4132BMFX-2.5 R4CB LM4132BMF-3.0 LM4132BMFX-3.0 R4DB LM4132BMF-3.3 LM4132BMFX-3.3 R4EB LM4132BMF-4.1 LM4132BMFX-4.1 R4FB LM4132CMF-1.8 LM4132CMFX-1.8 R4AC LM4132CMF-2.0 LM4132CMFX-2.0 R4BC LM4132CMF-2.5 LM4132CMFX-2.5 R4CC LM4132CMF-3.0 LM4132CMFX-3.0 R4DC LM4132CMF-3.3 LM4132CMFX-3.3 R4EC LM4132CMF-4.1 LM4132CMFX-4.1 R4FC LM4132DMF-1.8 LM4132DMFX-1.8 R4AD LM4132DMF-2.0 LM4132DMFX-2.0 R4BD LM4132DMF-2.5 LM4132DMFX-2.5 R4CD LM4132DMF-3.0 LM4132DMFX-3.0 R4DD LM4132DMF-3.3 LM4132DMFX-3.3 R4ED LM4132DMF-4.1 LM4132DMFX-4.1 R4FD LM4132EMF-1.8 LM4132EMFX-1.8 R4AE LM4132EMF-2.0 LM4132EMFX-2.0 R4BE LM4132EMF-2.5 LM4132EMFX-2.5 R4CE LM4132EMF-3.0 LM4132EMFX-3.0 R4DE LM4132EMF-3.3 LM4132EMFX-3.3 R4EE LM4132EMF-4.1 LM4132EMFX-4.1 R4FE Pin Descriptions Pin # Name Function 1 N/C No connect pin, leave floating 2 GND Ground 3 EN Enable pin www.national.com 4 VIN Input supply 5 VREF Reference output 2 Lead Temperature If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Infrared (15sec) Maximum Voltage on any input Vapor Phase (60 sec) 260C 215C 220C ESD Susceptibility (Note 3) Human Body Model -0.3 to 6V Output short circuit duration (soldering, 10sec) 2kV Indefinite Power Dissipation (TA = 25C) (Note 2) Storage Temperature Range Operating Ratings 350mW Maximum Input Supply Voltage -65C to 150C 5.5V Maximum Enable Input Voltage VIN Maximum Load Current 20mA Junction Temperature Range (TJ) -40C to +125C Electrical Characteristics LM4132-1.8 (VOUT = 1.8V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Typ Min (Note Max (Note 4) 5) (Note 4) LM4132A-1.8 (A Grade - 0.05%) -0.05 0.05 LM4132B-1.8 (B Grade - 0.1%) -0.1 0.1 LM4132C-1.8 (C Grade - 0.2%) -0.2 0.2 LM4132D-1.8 (D Grade - 0.4%) -0.4 0.4 LM4132E-1.8 (E Grade - 0.5%) -0.5 0.5 LM4132A-1.8 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-1.8 20 LM4132C-1.8 20 -40C TJ +125C 30 Supply Current Supply Current in Shutdown 60 100 A EN = 0V 3 7 A 120 ppm / mA VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 30 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VREF VIN - VREF ppm / C 20 LM4132E-1.8 IQ_SD % Temperature Coefficient LM4132D-1.8 IQ Unit Output Voltage Initial Accuracy ppm / V ppm Dropout Voltage (Note 9) ILOAD = 10mA 230 VN Output Noise Voltage 0.1 Hz to 10 Hz 170 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 3 400 mV VPP %VIN www.national.com LM4132 Absolute Maximum Ratings (Note 1) LM4132 Electrical Characteristics LM4132-2.0 (VOUT = 2.048V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Typ Min (Note Max (Note 4) 5) (Note 4) LM4132A-2.0 (A Grade - 0.05%) -0.05 0.05 LM4132B-2.0 (B Grade - 0.1%) -0.1 0.1 LM4132C-2.0 (C Grade - 0.2%) -0.2 0.2 LM4132D-2.0 (D Grade - 0.4%) -0.4 0.4 LM4132E-2.0 (E Grade - 0.5%) -0.5 0.5 LM4132A-2.0 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-2.0 20 LM4132C-2.0 20 -40C TJ +125C 30 Supply Current 60 100 7 Supply Current in Shutdown EN = 0V 3 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 30 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VREF VIN - VREF ppm / C 20 LM4132E-2.0 IQ_SD % Temperature Coefficient LM4132D-2.0 IQ Unit Output Voltage Initial Accuracy A A ppm / V 120 ppm / mA ppm Dropout Voltage (Note 9) ILOAD = 10mA 175 VN Output Noise Voltage 0.1 Hz to 10 Hz 190 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level www.national.com 65 4 400 mV VPP %VIN over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (Note 4) Typ (Note 5) (A Grade - 0.05%) -0.05 0.05 LM4132B-2.5 (B Grade - 0.1%) -0.1 0.1 LM4132C-2.5 (C Grade - 0.2%) -0.2 0.2 LM4132D-2.5 (D Grade - 0.4%) -0.4 0.4 LM4132E-2.5 (E Grade - 0.5%) -0.5 0.5 Temperature Coefficient LM4132A-2.5 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-2.5 20 LM4132C-2.5 20 -40C TJ +125C 30 Supply Current 60 100 A 3 7 A 120 ppm / mA EN = 0V VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 50 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VIN - VREF ppm / C 20 Supply Current in Shutdown VREF % LM4132A-2.5 LM4132E-2.5 IQ_SD Unit Output Voltage Initial Accuracy LM4132D-2.5 IQ Max (Note 4) ppm / V ppm Dropout Voltage (Note 9) ILOAD = 10mA 175 VN Output Noise Voltage 0.1 Hz to 10 Hz 240 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 5 400 mV VPP %VIN www.national.com LM4132 Electrical Characteristics LM4132-2.5 (VOUT = 2.5V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply LM4132 Electrical Characteristics LM4132-3.0 (VOUT = 3.0V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min Typ (Note 4) (Note 5) (A Grade - 0.05%) -0.05 0.05 LM4132B-3.0 (B Grade - 0.1%) -0.1 0.1 LM4132C-3.0 (C Grade - 0.2%) -0.2 0.2 LM4132D-3.0 (D Grade - 0.4%) -0.4 0.4 LM4132E-3.0 (E Grade - 0.5%) -0.5 0.5 Temperature Coefficient LM4132A-3.0 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-3.0 20 LM4132C-3.0 20 -40C TJ +125C 30 Supply Current 60 100 A 7 A 120 ppm / mA EN = 0V 3 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 70 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VIN - VREF ppm / C 20 Supply Current in Shutdown VREF % LM4132A-3.0 LM4132E-3.0 IQ_SD Unit Output Voltage Initial Accuracy LM4132D-3.0 IQ Max (Note 4) ppm / V ppm Dropout Voltage (Note 9) ILOAD = 10mA 175 VN Output Noise Voltage 0.1 Hz to 10 Hz 285 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level www.national.com 65 6 400 mV VPP %VIN over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min Typ Max (Note 4) (Note 5) (Note 4) LM4132A-3.3 (A Grade - 0.05%) -0.05 0.05 LM4132B-3.3 (B Grade - 0.1%) -0.1 0.1 LM4132C-3.3 (C Grade - 0.2%) -0.2 0.2 LM4132D-3.3 (D Grade - 0.4%) -0.4 0.4 LM4132E-3.3 (E Grade - 0.5%) -0.5 0.5 LM4132A-3.3 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-3.3 20 LM4132C-3.3 20 -40C TJ +125C 30 Supply Current 60 100 A 3 7 A 120 ppm / mA Supply Current in Shutdown EN = 0V VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 85 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VREF VIN - VREF ppm / C 20 LM4132E-3.3 IQ_SD % Temperature Coefficient LM4132D-3.3 IQ Unit Output Voltage Initial Accuracy ppm / V ppm Dropout Voltage (Note 9) ILOAD = 10mA 175 VN Output Noise Voltage 0.1 Hz to 10 Hz 310 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 7 400 mV VPP %VIN www.national.com LM4132 Electrical Characteristics LM4132-3.3 (VOUT = 3.3V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply LM4132 Electrical Characteristics LM4132-4.1 (VOUT = 4.096V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C unless otherwise specified. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Typ Min (Note Max (Note 4) 5) (Note 4) LM4132A-4.1 (A Grade - 0.05%) -0.05 0.05 LM4132B-4.1 (B Grade - 0.1%) -0.1 0.1 LM4132C-4.1 (C Grade - 0.2%) -0.2 0.2 LM4132D-4.1 (D Grade - 0.4%) -0.4 0.4 LM4132E-4.1 (E Grade - 0.5%) -0.5 0.5 LM4132A-4.1 0C TJ + 85C 10 -40C TJ +125C 20 LM4132B-4.1 20 LM4132C-4.1 20 -40C TJ +125C 30 Supply Current 60 100 3 7 Supply Current in Shutdown EN = 0V VREF/VIN Line Regulation VREF + 400mV VIN 5.5V VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (Note 7) 1000 Hrs 50 Thermal Hysteresis (Note 8) -40C TJ +125C 75 VREF VIN - VREF ppm / C 20 LM4132E-4.1 IQ_SD % Temperature Coefficient LM4132D-4.1 IQ Unit Output Voltage Initial Accuracy 100 A A ppm / V 120 ppm / mA ppm Dropout Voltage (Note 9) ILOAD = 10mA 175 VN Output Noise Voltage 0.1 Hz to 10 Hz 350 400 ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 mV VPP %VIN Note 1: Absolute Maximum Ratings indicate limits beyond which damage may occur to the device. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Note 2: Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by TJMAX (maximum junction temperature), J-A (junction to ambient thermal resistance) and TA (ambient temperature). The maximum power dissipation at any temperature is: PDissMAX = (TJMAX - TA) /J-A up to the value listed in the Absolute Maximum Ratings. J-A for SOT23-5 package is 220C/W, TJMAX = 125C. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 4: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control. Note 5: Typical numbers are at 25C and represent the most likely parametric norm. Note 6: Temperature coefficient is measured by the "Box" method; i.e., the maximum VREF is divided by the maximum T. Note 7: Long term stability is VREF @ 25C measured during 1000 hrs. Note 8: Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Note 9: Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. www.national.com 8 LM4132 Typical Performance Characteristics for 1.8V Output Voltage vs Temperature Load Regulation 20151364 20151367 Line Regulation 0.1-10Hz Noise Spectrum 20151379 20151368 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151376 20151373 9 www.national.com LM4132 Typical Performance Characteristics for 2.048V Output Voltage vs Temperature Load Regulation 20151304 20151303 Line Regulation 0.1 - 10 Hz Noise 20151314 20151309 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151340 www.national.com 20151315 10 LM4132 Typical Performance Characteristics for 2.5V Output Voltage vs Temperature Load Regulation 20151354 20151355 Line Regulation 0.1 - 10 Hz Noise 20151321 20151356 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151357 20151358 11 www.national.com LM4132 Typical Performance Characteristics for 3.0V Output Voltage vs Temperature Load Regulation 20151365 20151369 Line Regulation 0.1-10 Hz Noise Spectrum 20151380 20151370 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151374 www.national.com 20151377 12 LM4132 Typical Performance Characteristics for 3.3V Output Voltage vs Temperature Load Regulation 20151366 20151371 Line Regulation 0.1-10 Hz Noise Spectrum 20151381 20151372 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151378 20151375 13 www.national.com LM4132 Typical Performance Characteristics for 4.096V Output Voltage vs Temperature Load Regulation 20151360 20151359 Line Regulation 0.1 - 10 Hz Noise 20151319 20151361 Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 20151362 www.national.com 20151363 14 LM4132 Typical Performance Characteristics Dropout vs Load to 0.5% Accuracy Supply Current vs Input Voltage 20151308 20151353 Enable Threshold Voltage and Hysteresis Shutdown IQ vs Temperature 20151310 20151317 Typical Long Term Stability Ground Current vs Load Current 20151330 20151318 15 www.national.com LM4132 Typical Performance Characteristics (Continued) Typical Thermal Hysteresis Turn-On Transient Response 20151352 20151331 Line Transient Response VIN = 4V to 5.5V Load Transient Response ILOAD = 0 to 10mA 20151350 www.national.com 20151351 16 Thermal hysteresis is defined as the change in output voltage at 25oC after some deviation from 25oC. This is to say that thermal hysteresis is the difference in output voltage between two points in a given temperature profile. An illustrative temperature profile is shown in Figure 1. THEORY OF OPERATION The foundation of any voltage reference is the band-gap circuit. While the reference in the LM4132 is developed from the gate-source voltage of transistors in the IC, principles of the band-gap circuit are easily understood using a bipolar example. For a detailed analysis of the bipolar band-gap circuit, please refer to Application Note AN-56. SUPPLY AND ENABLE VOLTAGES To ensure proper operation, VEN and VIN must be within a specified range. An acceptable range of input voltages is VIN > VREF + 400mV (ILOAD 10mA) The enable pin uses an internal pull-up current source (IPULL_UP ) 2A) that may be left floating or triggered by an external source. If the part is not enabled by an external source, it may be connected to VIN. An acceptable range of enable voltages is given by the enable transfer characteristics. See the Electrical Characteristics section and Enable Transfer Characteristics figure for more detail. Note, the part will not operate correctly for VEN > VIN. 20151338 FIGURE 1. Illustrative Temperature Profile This may be expressed analytically as the following: COMPONENT SELECTION A small ceramic (X5R or X7R) capacitor on the input must be used to ensure stable operation. The value of CIN must be sized according to the output capacitor value. The value of CIN must satisfy the relationship CIN COUT. When no output capacitor is used, CIN must have a minimum value of 0.1F. Noise on the power-supply input may affect the output noise. Larger input capacitor values (typically 4.7F to 22F) may help reduce noise on the output and significantly reduce overshoot during startup. Use of an additional optional bypass capacitor between the input and ground may help further reduce noise on the output. With an input capacitor, the LM4132 will drive any combination of resistance and capacitance up to VREF/20mA and 10F respectively. The LM4132 is designed to operate with or without an output capacitor and is stable with capacitive loads up to 10F. Connecting a capacitor between the output and ground will significantly improve the load transient response when switching from a light load to a heavy load. The output capacitor should not be made arbitrarily large because it will effect the turn-on time as well as line and load transients. While a variety of capacitor chemistry types may be used, it is typically advisable to use low esr ceramic capacitors. Such capacitors provide a low impedance to high frequency signals, effectively bypassing them to ground. Bypass capacitors should be mounted close to the part. Mounting bypass capacitors close to the part will help reduce the parasitic trace components thereby improving performance. Where VHYS = Thermal hysteresis expressed in ppm VREF = Nominal preset output voltage VREF1 = VREF before temperature fluctuation VREF2 = VREF after temperature fluctuation. The LM4132 features a low thermal hysteresis of 75 ppm (typical) from -40C to 125C after 8 temperature cycles. TEMPERATURE COEFFICIENT Temperature drift is defined as the maximum deviation in output voltage over the operating temperature range. This deviation over temperature may be illustrated as shown in Figure 2. SHORT CIRCUITED OUTPUT The LM4132 features indefinite short circuit protection. This protection limits the output current to 75mA when the output is shorted to ground. 20151339 FIGURE 2. Illustrative VREF vs Temperature Profile TURN ON TIME Turn on time is defined as the time taken for the output voltage to rise to 90% of the preset value. The turn on time depends on the load. The turn on time is typically 33.2s when driving a 1F load and 78.8s when driving a 10F load. Some users may experience an extended turn on time (up to 10ms) under brown out conditions and low temperatures (-40C). Temperature coefficient may be expressed analytically as the following: 17 www.national.com LM4132 THERMAL HYSTERESIS Application Information LM4132 Application Information (Continued) TD = Temperature drift VREF = Nominal preset output voltage VREF_MIN = Minimum output voltage over operating temperature range VREF_MAX = Maximum output voltage over operating temperature range Where: VREF is in volts (V) and VERROR is in milli-volts (mV). Voltage error (mV) to percentage error (percent): T = Operating temperature range. The LM4132 features a low temperature drift of 10ppm (max) to 30ppm (max), depending on the grade. LONG TERM STABILITY Long-term stability refers to the fluctuation in output voltage over a long period of time (1000 hours). The LM4132 features a typical long-term stability of 50ppm over 1000 hours. The measurements are made using 5 units of each voltage option, at a nominal input voltage (5V), with no load, at room temperature. Where: VREF is in volts (V) and VERROR is in milli-volts (mV). PRINTED CIRCUIT BOARD and LAYOUT CONSIDERATIONS References in SOT packages are generally less prone to PC board mounting than devices in Small Outline (SOIC) packages. To minimize the mechanical stress due to PC board mounting that can cause the output voltage to shift from its initial value, mount the reference on a low flex area of the PC board, such as near the edge or a corner. The part may be isolated mechanically by cutting a U shape slot on the PCB for mounting the device. This approach also provides some thermal isolation from the rest of the circuit. EXPRESSION OF ELECTRICAL CHARACTERISTICS Electrical characteristics are typically expressed in mV, ppm, or a percentage of the nominal value. Depending on the application, one expression may be more useful than the other. To convert one quantity to the other one may apply the following: ppm to mV error in output voltage: Bypass capacitors must be mounted close to the part. Mounting bypass capacitors close to the part will reduce the parasitic trace components thereby improving performance. Where: VREF is in volts (V) and VERROR is in milli-volts (mV). Bit error (1 bit) to voltage error (mV): VREF is in volts (V), VERROR is in milli-volts (mV), and n is the number of bits. mV to ppm error in output voltage: www.national.com 18 LM4132 Typical Application Circuits 20151326 FIGURE 3. Voltage Reference with Complimentary Output 20151327 FIGURE 4. Precision Voltage Reference with Force and Sense Output 20151328 FIGURE 5. Programmable Current Source 19 www.national.com LM4132 SOT-23 Precision Low Dropout Voltage Reference Physical Dimensions inches (millimeters) unless otherwise noted SOT23-5 Package NS Package Number MF05A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated