ISO 9001: 201 2015 IXYS Integrated Circuits Product Catalog 2018 - 2019 High Voltage, Analog & Mixed Signal ICs, Optically Isolated Devices IXYS Integrated Circuits IXYS Integrated Circuits, formerly a wholly owned subsidiary of IXYS Corporation, is now part of Littelfuse. IXYS Integrated Circuits designs, manufactures, and markets a wide variety of semiconductor devices and is a major provider of optically isolated electronic components. IXYS Integrated Circuits IXYS Integrated Circuits' unique mix of high voltage wafer fabrication, isolation barrier expertise, multi-chip packaging experience, and expertise in analog, mixed signal, and power design, points the way to greater functionality in a smaller footprint at lower cost for your designs. Products and Markets * IGBT and MOSFET Drivers: High voltage, low-side, and optically isolated IGBT and MOSFET drivers, many of which are AEC-Q100 qualified. * High Voltage ICs: High voltage 8-channel and 16-channel analog switches for the medical and imaging markets, high voltage LED drivers, and others. * Solid State Relays (SSR): One of the industry's broadest lines of optically isolated SSRs, available in a wide selection of configurations, blocking voltages, and load currents. * Power Market: Power solid state relays; SCR-based AC power switches (zero-cross & rapid turn-on); and N-channel, depletion-mode, field effect transistors (FET). * Lighting: High voltage LED drivers. * High Speed Digital Optical Isolators: High speed isolators that pass DC signals, require no refresh clocking, and provide 3750Vrms of galvanic isolation. * I2C Optically Isolated Bus Repeaters: New high speed repeaters that buffer both I2C signals, require no refresh clocking, and provide 3750Vrms of galvanic isolation. * Portable reader devices: Drivers for ePaper readers and displays. * RFID Devices: Read-Only and HDX devices for single transponder applications operating in the low frequency (134.2 kHz) range, and supporting ISO 11784/85 standards. * Non-volatile Digitally Programmable Capacitors: Provide capacitive offset trimming for capacitance sensitive circuits. * Telecommunications: a broad range of products: LITELINK(R) silicon Data Access Arrangement (DAA) Phone-line interface and monitoring devices LCAS: Line Card Access Switch products DC Termination devices for xDSL and ISDN applications CybergateTM DAA 2 IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com TABLE OF CONTENTS HIGH VOLTAGE PRODUCTS PART NUMBER INDEX HIGH VOLTAGE ANALOG SWITCH ARRAYS ................................................26 HIGH VOLTAGE ISOLATED ANALOG SWITCHES ...........................................27 NUMERICAL INDEX TO ALL PRODUCT CATALOG DEVICES ...............................4 HIGH SPEED DIGITAL OPTICAL ISOLATORS SOLID STATE RELAYS OPTICALLY ISOLATED I2C BUS REPEATERS ..............................................30 SINGLE-CHANNEL EACH DIRECTION DIGITAL OPTICAL ISOLATOR ..................31 DUAL HIGH SPEED DIGITAL OPTICAL ISOLATOR ........................................31 1-FORM-A RELAYS (NORMALLY OPEN).....................................................7 1-FORM-B RELAYS (NORMALLY CLOSED) ...............................................10 MISCELLANEOUS RELAYS ......................................................................11 SINGLE & DUAL OPTOCOUPLERS ...........................................................32 LINEAR OPTOCOUPLERS .......................................................................33 CURRENT LIMITING SSRS WITH VTS AND THM.......................................13 OPTICALLY ISOLATED POWER RELAYS 1-FORM-A POWER RELAYS ..................................................................15 1-FORM-B POWER RELAYS ..................................................................15 OPTICALLY ISOLATED AC POWER SWITCHES OPTICALLY ISOLATED AC POWER SWITCHES: LOAD CURRENT 1A .............16 OPTICALLY ISOLATED AC POWER SWITCHES: LOAD CURRENT >1A .............17 LIGHTING & DISPLAY PRODUCTS HIGH VOLTAGE LED DRIVERS ...............................................................34 TELECOMMUNICATIONS PRODUCTS LITELINKTM SILICON DAA PHONE LINE INTERFACE ...............................36 SINGLE-CHANNEL VOICE-BAND CODEC ..................................................37 CALL PROGRESS TONE DETECTOR.........................................................37 LINE CARD ACCESS SWITCHES (LCAS).................................................38 LCAS FOR RINGING SLIC ..................................................................39 CYBERGATETM DATA ACCESS ARRANGEMENT (DAA) MODULES ..................39 DC TERMINATION ICS (XDSL, ISDN) ...................................................40 TELECOM MULTIFUNCTION PRODUCTS .....................................................41 LINE SENSE RELAY .............................................................................41 MULTIFUNCTION PRODUCTS: SSR/OPTOCOUPLER GENERAL PURPOSE MULTIFUNCTION PRODUCTS .......................................18 TELECOM MULTIFUNCTION PRODUCTS .....................................................41 FIELD EFFECT TRANSISTORS N-CHANNEL DEPLETION MODE FETS ....................................................19 VOLTAGE MONITORING & SENSING ICS IGBT & MOSFET GATE DRIVERS LOW-SIDE GATE DRIVERS ....................................................................20 600V HIGH SIDE & LOW SIDE GATE DRIVER..........................................21 HIGH VOLTAGE HALF-BRIDGE GATE DRIVER ............................................21 1200V HIGH AND LOW SIDE GATE DRIVER ............................................22 600V HIGH SIDE IGBT & MOSFET GATE DRIVER ...............................22 2.5A OUTPUT OPTICALLY COUPLED GATE DRIVER ...................................23 2.5A OUTPUT HI SPEED GATE DRIVER OPTOCOUPLER .............................23 OPTICALLY ISOLATED PHOTOVOLTAIC GATE DRIVERS ..................................24 OPTICALLY ISOLATED LOAD-BIASED GATE DRIVERS ...................................25 VOLTAGE MONITORING DEVICES.............................................................42 LOW VOLTAGE ERROR AMP WITH HIGH VOLTAGE DARLINGTON TRANSISTOR...43 OPTICALLY ISOLATED ERROR AMPLIFIERS ................................................44 RFID PRODUCTS RFID TAGS .......................................................................................45 DIGITALLY PROGRAMMABLE CAPACITORS NON-VOLATILE DIGITAL PROGRAMMABLE CAPACITORS ...............................46 Note: Drawings and photographs of IXYS Integrated Circuits products shown in this catalog are for illustrative purposes only and do not necessarily portray accurate physical details, marking, or branding. They exist solely to provide additional useful information. 3 +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 Table of Contents OPTOCOUPLERS FAULT PROTECTED RELAYS PART NUMBER INDEX Part Number Index CPC1001N 32 CPC1301 32 CPC1786J 15 CPC1977J 15 CPC3982 19 CYG2020 39 CPC1002N 11 CPC1302 32 CPC1788J 15 CPC1978J 15 CPC40055ST 17 CYG2100 39 CPC1004N 11 CPC1303 32 CPC1906Y 15 CPC1979J 15 CPC5001 31 CYG2110 39 CPC1006N 7 CPC1317 7 CPC1907B 15 CPC1981Y 15 CPC5002 31 CYG2111 39 CPC1008N 7 CPC1330 7 CPC1908J 15 CPC1983B 15 CPC5602 19 CYG2217 39 CPC1009N 7 CPC1333 10 CPC1909J 15 CPC1983Y 15 CPC5603 19 CYG2218 39 CPC1010N 7 CPC1335 7 CPC1916Y 15 CPC1983YE 15 CPC5620 34 CYG2320 39 CPC1014N 7 CPC1390 7 CPC1918J 15 CPC1984Y 15 CPC5621 34 FDA215 24 CPC1016N 7 CPC1393 7 CPC1926Y 15 CPC1986J 15 CPC5622 34 FDA217 24 CPC1017N 7 CPC1394 7 CPC1927J 15 CPC1988J 15 CPC5710 42 IAA110 18 CPC1018N 7 CPC1465 40 CPC1943 16 CPC1998J 17 CPC5712 42 IAB110 18 CPC1019N 7 CPC1466 40 CPC1945G 16 CPC2014N 9 CPC5750 37 IAD110 18 CPC1020N 7 CPC1510 7, 13 CPC1945Y 16 CPC2017N 9 CPC5902 30 IBB110 18 CPC1025N 7 CPC1511 7, 13 CPC1961 16 CPC2025N 9 CPC5903 30 ITC117 41 CPC1030N 7 CPC1540 7, 13 CPC1963 16 CPC2030N 9 CPC7220 26 ITC117L 41 CPC1035N 7 CPC1560 7, 13 CPC1964B 17 CPC2125N 10 CPC7232 26 ITC135 41 CPC1106N 10 CPC1563 7, 13 CPC1964BX6 17 CPC2317N 11 CPC7508 39 ITC137 41 CPC1114N 10 CPC1580 25 CPC1965G 16 CPC2330N 11 CPC7512 29 IX2113 21 CPC1117N 10 CPC1590 25 CPC1965Y 16 CPC2907B 15 CPC7514 28 IX2120 22 CPC1125N 10 CPC1593 7, 13 CPC1966Y 17 CPC3701 19 CPC7524 27 IX2127 22 CPC1130N 10 CPC1596 25 CPC1966B 17 CPC3703 19 CPC7591 38 IX21844 21 CPC1135N 10 CPC1705Y 15 CPC1966BX8 17 CPC3708 19 CPC7592 38 IX3120 23 CPC1150N 10 CPC1706Y 15 CPC1966YX6 17 CPC3710 19 CPC7601 26 IX3180 23 CPC1215 11 CPC1708J 15 CPC1966YX8 17 CPC3714 19 CPC7691 38 IX332B 24 CPC1217 11 CPC1709J 15 CPC1967J 15 CPC3720 19 CPC7692 38 IX4340 20 CPC1218 11 CPC1718J 15 CPC1968J 15 CPC3730 19 CPC7695 38 IX4340NE 20 CPC1219 12 CPC1726Y 15 CPC1972 16 CPC3902 19 CPC7701 26 IX4423 20 7 CPC1727J 15 CPC1973Y 15 CPC3909 19 CPC9909 35 IX4424 20 CPC1230N 7 CPC1777J 15 CPC1976 17 CPC3960 19 CYG2000 39 IX4425 20 CPC1231N 10 CPC1779J 15 CPC1976YX6 17 CPC3980 19 CYG2011 39 IX4426 20 CPC1225N 4 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com PLA134 8 XAA170 9 LOC211 33 PLA140 8 XBB170 10 M-949-11 41 PLA140L 8 XCA170 8 10 M-980-02 37 PLA143 8 XCB170 10 10 MXHV9910 34 PLA150 8 XS170 18 LCB716 10 NCD1015ZP 45 PLA160 8 10 LCB717 10 NCD1015M 45 PLA170 8 10 LCC110 12 NCD2100 47 PLA171 8 LBB127 10 LCC120 12 NCD2400M 46 PLA172P 8 LCA100 7 LDA100 32 OAA160 9 PLA190 8 20 LCA100L 7 LDA101 32 OMA160 8 PLA191 8 20 LCA110 7 LDA102 32 PAA110 9 PLA192 8 IXD_614SI 20 LCA110L 7 LDA110 32 PAA110L 9 PLA193 8 IXD_630 20 LCA120 7 LDA111 32 PAA127 9 PLA194 8 IXD_630M 20 LCA120L 7 LDA200 32 PAA132 9 PLB150 10 LAA100 9 LCA125 7 LDA201 32 PAA140 9 PLB171 10 LAA100L 9 LCA125L 7 LDA202 32 PAA140L 9 PLB190 10 LAA108 9 LCA127 8 LDA203 32 PAA150 9 PM1204 16 LAA110 9 LCA127L 8 LDA210 32 PAA190 9 PM1205 16 LAA110L 9 LCA129 8 LDA211 32 PAA191 9 PM1206 16 LAA120 9 LCA182 8 LDA212 32 PAA193 9 PS1201 16 LAA120L 9 LCA210 12 LDA213 32 PBA150 11 PS2401 16 LAA125 9 LCA210L 12 LIA120 44 PBB150 10 PS2601 16 LAA125L 9 LCA220 12 LIA130 44 PBB190 10 TS117 18 LAA127 9 LCA701 8 LIA135 44 PD1201 16 TS117L 18 LAA127L 9 LCA710 8 LIA136 44 PD2401 16 TS118 18 LAA710 9 LCA712 8 LOC110 33 PD2601 16 TS120 18 LBA110 11 LCA715 8 LOC111 33 PLA110 8 TS190 18 LBA110L 11 LCA717 8 LOC112 33 PLA110L 8 TS190L 18 LBA120 11 LCB110 10 LOC117 33 PLA132 8 XAA117 9 20 LBA120L 11 LCB111 10 LOC210 IX4428 20 LBA127 11 LCB120 10 IX9907 34 LBA127L 11 LCB126 10 IX9908 35 LBA710 11 LCB127 IX9915 43 LBA716 11 LCB710 IXD_602 20 LBB110 10 IXD_604 20 LBB120 IXD_604SI 20 LBB126 IXD_604SIA 20 IXD_609 20 IXD_609SI IXD_614 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 Part Number Index 33 IX4427 5 SOLID STATE RELAYS 4-Pin SOP Type BI 4-Pin SIP (8-Pin Body) 10 6-Pin Surface Mount Type BI+ (BI) Type UNI Load Load + Load Load Do Not Use Load - Load Polarity Dependent Control Input 12 Control Input +V 6-Pin DIP Load Voltage -V +I 42 14 +V Load Voltage 4-Pin DIP -V +I Solid State Relays Load Current Load Current -I 44-Pin Pin Surface Mount 8-Pin SOP + Load - Load Polarity Independent 41 Type BI+ (UNI) -I All waveforms are into a resistive load 43 17 Type BI relays conduct load current in both directions. Type BI+ relays, in BI configuration, conduct load current in both directions. 4-Pin V-DIP 8-Pin DIP Type UNI relays conduct load current from the positive terminal to the negative terminal only. 44 Type BI+ relays, in UNI configuration with output MOSFETs wired in parallel, enable higher load current from positive terminal to negative terminal only. 20 4-Pin DIP (14-Pin Body) The accompanying SSR tables reference these types (BI, BI+, & UNI) for all devices listed. 8-Pin Flatpack 21 * Replace electromechanical relays * Replace mechanical switches * Implement computer control 61 8-Pin Surface Mount of electromechanical circuits 6-Pin Flatpack (8-Pin Body) 22 4-Pin SIP (8-Pin Body) 36 6 62 Packages are referenced by number in the accompanying solid state relay selection tables. Features: Applications: * Low drive current * High reliability * No EMI/RFI generation * Arc-free with no snubbing circuits * AC or DC switching * Current limiting devices available * FCC compatible * Low off-state leakage * Telecommunications/data communications * Instrumentation * Multiplexers * Data acquisition/electronic switching * Meters (Watt-hour, water, gas) * Medical equipment (patient/equipment isolation) * Security * Aerospace * Industrial controls For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com * 1-FORM-A RELAYS (NORMALLY OPEN) BI+ BI 1-Form-A Relays: Single-Pole Relay Type Blocking Voltage Load Current On Resistance BI (VP) 60 (mA) CPC1006N CPC1008N CPC1009N CPC1010N CPC1014N CPC1016N CPC1017N CPC1018N CPC1019N CPC1020N CPC1025N CPC1030N CPC1035N CPC1225N CPC1230N CPC1317 CPC1330 CPC1335 CPC1390 CPC1393 CPC1394 CPC1510 CPC1511 CPC1540 CPC1560 CPC1563 CPC1593 LCA100 LCA100L LCA110 LCA110L LCA120 LCA120L LCA125 LCA125L BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI+ BI BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ 100 100 250 60 100 60 60 60 30 400 350 350 400 350 70 350 350 400 600 600 250 230 350 60 600 600 350 350 350 350 250 250 300 300 150 150 170 400 100 100 600 750 1200 120 120 100 120 120 150 120 100 140 90 120 200 450 120 300 120 120 120 120 120 120 170 150 170 170 75 Switching Speeds ton / toff (ms) 10 / 10 Isolation Voltage Off-State Leakage () 10 Input Control Current (mA) 0.5 (Vrms) 1500 (A) 1 8 8 11.5 2 16 16 0.8 0.6 0.25 30 30 35 30 30 16 30 35 22 50 35 15 4 25 5.6 35 35 25 25 35 35 20 20 16 20 2 2 2 2 2 1 1 2 2 2 2 2 2 2 1 2 1 2 2 2 2 2.5 2 1.1 2 2 5 5 2 2 5 5 5 5 2/1 2 / 0.5 3/3 2/1 2/1 10 / 10 3/2 3/3 3/3 2/1 2/1 2/1 2/1 2/1 2.5 / 2.5 2/1 10 / 10 1/1 5/5 5/3 2/2 4/2 2/2 0.1 / 0.4 2/2 2/2 5/5 5/5 3/3 3/3 3/3 3/3 5/5 5/5 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 3750 5000 3750 5000 5000 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 1 0.02 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Package Type (Page 6) Features and Comments Low IF , EN 50130-4 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 21 42, 43 21 42, 43, 44 42, 43, 44 42, 43, 44 12, 14 36 12, 14 20, 22 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 Very low off-state ILEAK 20nA EN 50130-4 Low IF , EN 50130-4 Low IF , EN 50130-4 High load current, very low on-resistance EN/IEC 60950-1 Supplementary Insulation (0.4mm distance through insulation) EN/IEC 60950-1 Supplementary Insulation (0.4mm distance through insulation) EN 50130-4 (installation class 3), transient voltage suppression (TVS) Enhanced isolation voltage Low IF , EN 50130-4 (installation class 3), transient voltage suppression (TVS) Enhanced isolation voltage Enhanced isolation voltage Enhanced isolation voltage Current limiting with thermal management - see page 13 Current limiting with thermal management - see page 13 Current limiting with thermal management - see page 13 Current limiting with thermal management - see page 13 Current limiting with thermal management - see page 13 Current limiting, thermal management, voltage triggered shutdown - see page 13 Current limiting Current limiting Current limiting Current limiting For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service Solid State Relays Part Number +1 978 524 6768, +1 978 524 4900 7 BI BI+ 1-Form-A Relays: Single-Pole (continued) Solid State Relays Part Number Relay Type Blocking Voltage Load Current On Resistance () BI+ BI+ BI+ BI+ (VP) 250 250 250 350 (mA) LCA127 LCA127L LCA129 LCA182 200 170 170 120 10 15 20 35 LCA701 LCA710 LCA712 LCA715 LCA717 OMA160 PLA110 PLA110L PLA132 PLA134 PLA140 PLA140L PLA143 PLA150 PLA160 PLA170 PLA171 PLA172P PLA190 PLA191 PLA192 PLA193 PLA194 XCA170 BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI BI BI+ BI+ BI+ BI+ BI+ BI+ 100 60 60 60 30 250 400 400 60 100 400 400 600 250 300 800 800 800 400 400 600 600 600 350 1500 1000 1000 2200 2000 50 150 150 600 350 250 200 100 250 50 100 100 100 150 250 150 100 130 100 8 0.3 0.5 0.5 0.15 0.15 100 22 25 1 3 8 13 50 7 100 50 50 50 22 8 22 50 35 50 Input Control Current (mA) 5 5 2 0.25 2 10 10 5 2 10 5 5 2 5 5 5 2 5 10 5 2 2 5 5 5 5 2 5 Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage Package Type (Page 6) 5/5 5/5 8/8 3/3 (Vrms) 3750 3750 3750 3750 (A) 1 1 1 1 12, 14 12, 14 12, 14 12, 14 4/1 2.5 / 0.25 2.5 / 0.35 2.5 / 0.25 3/3 0.125 / 0.125 1 / 0.5 1 / 0.25 5/2 5/5 3/1 5/3 5/5 2.5 / 0.5 0.05 / 0.05 5/5 5/5 5/5 1 / 0.5 3/1 5/5 5/5 3/2 5/5 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 4000 3750 3750 3750 5000 5000 5000 5000 5000 5000 5000 3750 1 1 0.01 1 1 0.025 1 1 1 1 1 1 1 0.025 1 1 1 1 1 1 1 1 1 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 62 62 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 Features and Comments Current limiting Very low IF High load current High load current High load current, low ILEAK High load current High load current Low ILEAK , fast switching times Current limiting Current limiting Enhanced isolation voltage Low ILEAK , fast switching times Enhanced isolation voltage, high blocking voltage (output pins 7mm separation) -40C to +105C Operational Temperature Range Enhanced isolation voltage Enhanced isolation voltage Enhanced isolation voltage, PLA192E is DIN EN 60747-5-5 Certified Enhanced isolation voltage, PLA193E is DIN EN 60747-5-5 Certified Enhanced isolation voltage For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com BI 1-Form-A Relays: Dual Single-Pole Relay Type Blocking Voltage Load Current CPC2014N CPC2017N BI BI (VP) 60 60 (mA) 400 120 CPC2025N CPC2030N LAA100 LAA100L LAA108 LAA110 LAA110L LAA120 LAA120L LAA125 LAA125L LAA127 LAA127L LAA710 OAA160 PAA110 PAA110L PAA127 PAA132 PAA140 PAA140L PAA150 PAA190 PAA191 PAA193 XAA117 XAA170 BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI 400 350 350 350 100 350 350 250 250 350 350 250 250 60 250 400 400 280 60 400 400 250 400 400 600 60 350 120 120 120 120 300 120 120 170 150 170 150 200 170 1000 50 150 150 200 600 250 200 250 150 250 100 150 100 On Resistance () 2 16 30 30 25 25 8 35 35 20 25 16 18 10 10 0.5 100 22 25 10 1 8 13 7 22 8 50 16 50 Input Control Current (mA) 2 1 Switching Speeds ton / toff (ms) 2/1 3/3 Isolation Voltage Off-State Leakage Package Type (Page 6) (Vrms) 1500 1500 (A) 1 1 17 17 2 2 5 5 2 5 5 5 5 5 5 5 5 10 6 5 5 3 2 5 5 5 5 5 5 1 5 2/1 2/1 5/5 5/5 3/3 3/3 3/3 5/5 5/5 5/5 5/5 5/5 5/5 2.5 / 0.25 0.125 / 0.125 1 / 0.25 1 / 0.5 0.5 / 0.5 5/2 3/1 5/3 2.5 / 0.5 1 / 0.5 3/1 5/5 5/5 5/5 1500 1500 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 5000 5000 5000 3750 3750 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.025 1 1 0.025 1 1 1 1 1 1 10 1 1 17 17 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 22 20, 22 20, 21, 22 20, 21, 22 Features and Comments EN 50130-4 Low IF , EN 50130-4 Current limiting Current limiting Current limiting Current limiting Current limiting Very low ILEAK , fast switching times Current limiting Very low ILEAK , fast switching times Current limiting Enhanced isolation voltage Enhanced isolation voltage Enhanced isolation voltage Low IF For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service Solid State Relays Part Number +1 978 524 6768, +1 978 524 4900 9 * 1-FORM-B RELAYS (NORMALLY CLOSED) BI BI+ 1-Form-B Relays: Single-Pole Solid State Relays Part Number Relay Type Blocking Voltage Load Current On Resistance Switching Speeds ton / toff (ms) 10 / 10 Isolation Voltage Off-State Leakage () 10 Input Control Current (mA) 0.5 CPC1106N BI (VP) 60 (mA) 75 (Vrms) 1500 (A) 1 CPC1114N CPC1117N CPC1125N CPC1130N CPC1135N CPC1150N CPC1231N CPC1333 LCB110 LCB111 LCB120 LCB126 LCB127 LCB710 LCB716 LCB717 PLB150 PLB171 PLB190 XCB170 BI BI BI BI BI BI BI BI BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI+ BI BI+ BI+ 60 60 400 350 350 350 350 350 350 350 250 250 250 60 60 30 250 800 400 350 400 150 100 120 120 120 120 130 120 120 170 170 200 1000 500 1500 250 80 130 100 2 16 35 30 35 50 30 30 35 35 20 15 10 0.6 2 0.3 7 55 25 50 2 1 2 2 2 2 2 2 5 2 5 5 5 2 2 2 5 2 2 5 2/5 10 / 10 2/2 2/2 2/2 1/2 2/2 2/3 3/3 5/5 5/5 5/5 5/5 3/3 3/3 2/5 1 / 2.5 5/5 1 / 2.5 5/5 1500 1500 1500 1500 1500 1500 1500 5000 3750 3750 3750 3750 3750 3750 3750 3750 3750 5000 5000 3750 1 1 5 5 5 5 5 1 1 1 1 1 1 1 1 1 1 1 1 1 Package Type (Page 6) 10 10 10 10 10 10 10 10 42, 43 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 12, 14 62 12, 14 12, 14 Features and Comments Low IF , EN 50130-4 Low IF , EN 50130-4 EN/IEC 60950-1 Supplementary Insulation (0.4mm distance through insulation) Enhanced isolation voltage High load current High load current Enhanced isolation voltage, high blocking voltage (output pins 7mm separation) Enhanced isolation voltage 1-Form-B Relays: Dual Single-Pole Part Number Relay Type Blocking Voltage Load Current On Resistance CPC2125N LBB110 LBB120 LBB126 LBB127 PBB150 PBB190 XBB170 BI BI BI BI BI BI BI BI (VP) 400 350 250 250 250 250 400 350 (mA) 100 120 170 170 200 250 130 100 () 35 35 20 15 10 7 25 50 10 BI Input Control Current (mA) 2 5 5 5 5 5 2 5 Switching Speeds ton / toff (ms) 2/2 3/3 5/5 5/5 5/5 2.5 / 2.5 1 / 2.5 5/5 Isolation Voltage Off-State Leakage (Vrms) 1500 3750 3750 3750 3750 3750 5000 3750 (A) 5 1 1 1 1 1 1 1 Package Type (Page 6) Features and Comments 17 20, 21, 22 20, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com BI * MISCELLANEOUS RELAYS 1-Form-A & 1-Form-B Combination Relays Relay Type CPC2317N CPC2330N LBA110 LBA110L LBA120 LBA120L LBA127 LBA127L LBA710 LBA716 PBA150 BI BI BI BI BI BI BI BI BI BI BI Blocking Voltage Load Current On Resistance (VP) (mA) 120 120 120 120 170 150 200 150 1000 1000 250 () 16 30 35 35 20 25 10 15 0.6 0.4 7 60 350 350 350 250 250 250 250 60 60 250 Input Control Current (mA) 1 2 2 5 5 5 5 5 2 2 5 Switching Speeds ton / toff (ms) 3/3 3/3 3/3 3/3 5/5 5/5 5/5 5/5 5/5 5/5 2.5 / 2.5 Isolation Voltage (Vrms) 1500 1500 3750 3750 3750 3750 3750 3750 3750 3750 3750 Off-State Leakage A/B (A) 1/1 1/5 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 Package Type (Page 6) 17 17 20, 21, 22 20, 21, 22 20, 21, 22 20, 22 20, 21, 22 20, 22 20, 22 20, 22 20, 22 Features and Comments Low IF Current limiting Current limiting Current limiting High load current High load current UNI 1-Form-A Relays: Single-Pole, Unidirectional (DC-only) Part Number Relay Type Blocking Voltage Load Current On Resistance CPC1002N CPC1004N UNI UNI (VP) 60 100 (mA) 700 300 () 0.55 4 Input Control Current (mA) 2 2 Switching Speeds ton / toff (ms) 5/2 3/1 Isolation Voltage Off-State Leakage (Vrms) 1500 1500 A) 1 1 Package Type (Page 6) Features and Comments EN 50130-4 Extended operating temperature range: -40C to +110C 10 10 BI 1-Form-A Relays: Single-Pole, Voltage-Controlled Part Number Relay Type Blocking Voltage Load Current On Resistance CPC1215 CPC1217 CPC1218 BI BI BI (VP) 400 60 60 (mA) 500 200 600 () 6 16 1.1 Input Control Voltage (V) 5 - 12 5 - 12 5 - 12 Switching Speeds ton / toff (ms) 5/3 5/5 5/5 Solid State Relays Part Number Isolation Voltage Off-State Leakage (Vrms) 3750 2500 2500 (A) 1 1 1 Package Type (Page 6) 61 41 41 Features and Comments Direct drop-in reed relay replacement EN 50130-4, direct drop-in reed relay replacement EN 50130-4, direct drop-in reed relay replacement For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 11 BI 1-Form-B Relays: Single-Pole, Voltage-Controlled Part Number CPC1219 Relay Type BI Blocking Voltage Load Current On Resistance (VP) (mA) 60 200 Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage () Input Control Voltage (V) (Vrms) (A) 16 5 - 12 5/5 2500 1 Package Type (Page 6) Features and Comments 41 EN 50130-4, direct drop-in reed relay replacement BI 2-Form-A Relays: Double-Pole, Single-Throw Solid State Relays Part Number Relay Type Blocking Voltage Load Current On Resistance LCA210 LCA210L LCA220 BI BI BI (VP) 350 350 250 (mA) 85 85 120 () 35 35 20 Input Control Current (mA) 8 8 10 Switching Speeds ton / toff (ms) 3/3 4/4 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 3750 3750 (A) 1 1 1 Package Type (Page 6) Features and Comments 20, 22 20, 22 20, 22 Current limiting BI 1-Form-C Relays: Common Input, Single-Pole, Double-Throw Part Number LCC110 LCC120 12 Relay Type Blocking Voltage Load Current On Resistance BI BI (VP) 350 250 (mA) 120 170 () 35 20 Input Control Current (mA) 8 10 Switching Speeds ton / toff (ms) 4/4 5/5 Isolation Voltage Off-State Leakage (Vrms) 3750 3750 (A) 1 1 Package Type (Page 6) Features and Comments 20, 21, 22 20, 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com FAULT PROTECTED RELAYS * CURRENT LIMITING SSRS WITH VOLTAGE TRIGGERED SHUTDOWN & THERMAL MANAGEMENT 6-Pin Surface Mount * Active current-limiting circuitry * Integrated thermal management (ThM) * Voltage triggered shutdown (VTS) Power SIP 12 CPC1510 CPC1511 CPC1540 CPC1560 CPC1563 CPC1593 Blocking Voltage Input Control Current (VP) 250 230 350 60 600 600 On-Resistance (Maximum) Load Current (Maximum) 14 8-Pin DIP 20 Current Limit (Maximum) 22 * VTS Threshold Switching Speed DC-Only AC DC-Only AC DC-Only AC (VTH) (ton / toff) () 3.75 6.75 1.4 11.75 11.75 () 15 4 25 5.6 35 35 (mA) 350 250 600 250 250 (mA) 200 450 120 300 120 120 (mAP) 920 570 1500 570 570 (mAP) 450 1400 285 900 285 285 (V) 100 100 21 (ms) 2/2 4/2 2/2 0.1 / 0.4 2/2 2/2 (mA) 2 2.5 2 1.1 2 2 36 8-Pin Surface Mount Isolation Voltage Package Type (Vrms) 3750 3750 3750 3750 3750 3750 12, 14 36 12, 14 20, 22 12, 14 12, 14 Features & Comments Industrial applications Industrial applications PSTN hook switch applications Fast switching speeds High blocking voltage Power supply start-up * Deactivates the switch when the load voltage exceeds the VTH threshold while the switch is in current limit. CPC1540, CPC1563, CPC1593 OUT1 Gate Drive Control Thermal Management Voltage Triggered Shutdown (VTS) S1 OUT1 OUT2 S2 Applications: * Telephony hook switch * VoIP gateways * I/O subsystems * Electronic switching * Medical equipment (Patient/equipment isolation) * Security * Aerospace * Industrial controls Voltage Threshold Voltage Threshold Shutdown Delay VTH Voltage Threshold Reactivation Delay ILMT Time ILMT VTH S1 S2 Current Through Switch Performance into resistive load. OUT2 Line Voltage For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 13 Fault Protected Relays * Provide excellent power-cross immunity * Ideal for use in electromagnetically noisy environments * Resumes normal operation after faults are removed Part Number 66-Pin Pin DIP OPTICALLY ISOLATED POWER RELAYS Optically Isolated Power Relays * * * * * * Blocking voltage up to 1000VP On-resistance as low as 0.05 Ohms On/off times from 1ms to 25ms MOSFET-based AC/DC and DC-only power relays elays Load current up to 22.8ADC (with 5C/W heat sink sink) 2500V rms to 5000Vrms isolation from input to output and to DCB substrate Features: * Isolated, low thermal impedance pad for heat sink applications * Low input control current * Low thermal impedances, junction to case (JCC): 0.30C/W - ISOPLUS-264 0.35C/W - i4-PAC 1.50C/W - Power SIP 1.50C/W - Power SOIC Applications: 1-Form-A Bidirectional * Robotics * Medical equipment * Railroad/traffic controls * Consumer appliances * Industrial control * Test and measurement equipment 66 - Power SOIC 14 1-Form-A Unidirectional 1-Form-B Unidirectional Dual 1-Form-A Bidirectional Metallized, external, Direct Copper Bond (DCB) surface for heat sink applications 36 - Power SIP 29 - i4-PAC For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com 37 - ISOPLUS-264 * 1-FORM-A POWER RELAYS: SINGLE-POLE - BIDIRECTIONAL Relay Type (VP) CPC1906Y CPC1907B CPC1908J CPC1909J CPC1916Y CPC1918J CPC1926Y CPC1927J CPC1967J CPC1968J CPC1973Y CPC1977J CPC1978J CPC1979J CPC1981Y CPC1983B CPC1983Y CPC1983YE CPC1984Y CPC1986J CPC1988J BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI BI Load Current (Arms) Blocking Voltage 60 60 60 60 100 100 250 250 400 500 400 600 800 600 1000 600 600 600 600 1000 1000 Without Heat Sink 2 6 3.5 6.5 2.5 5.25 0.7 2.7 1.35 2 0.35 1.25 0.75 1.4 0.18 0.5 0.5 0.5 1 0.65 0.9 5C/W Heat Sink 8.5 15 13 6.7 3.35 5 3.1 1.85 3.5 1.6 2.25 On Resistance Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage (Vrms) (A) 10 / 5 5/1 20 / 5 25 / 10 5/3 25 / 10 10 / 10 25 / 10 20 / 5 20 / 5 5/3 20 / 5 20 / 5 25 / 5 10 / 5 5/2 5/2 5/2 10 / 2 20 / 5 20 / 5 2500 5000 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 5000 2500 4000 4000 2500 2500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 36 66 29 37 36 37 36 37 29 37 36 29 29 37 36 66 36 36 36 29 37 2.5 / 0.25 4000 1 66 Input Control Current (mA) Switching Speeds ton / toff (ms) Isolation Voltage Off-State Leakage Package Type (Page 14) (Vrms) (A) 5 10 10 10 10 10 10 10 10 10 5/2 20 / 5 20 / 5 20 / 5 5/2 20 / 5 20 / 5 20 / 5 20 / 5 20 / 5 2500 2500 2500 2500 2500 2500 2500 2500 2500 2500 1 1 1 1 1 1 1 1 1 1 36 29 37 37 36 37 29 37 29 37 2 / 12 2500 1 36 TC=25C () Input Control Current (mA) 15 15 15 15 13.15 15 12.25 7.25 14.5 6.5 9.4 0.3 0.06 0.3 0.1 0.34 0.1 1.4 0.2 0.85 0.35 5 1 2.3 0.75 18 6 6 6 0.66 3 2.5 10 5 10 10 10 10 10 10 10 10 10 10 10 10 10 5 5 5 5 10 10 0.15 5 Package Type (Page 14) Features & Comments Enhanced isolation voltage Optically Isolated Power Relays Part Number Enhanced isolation voltage Enhanced isolation voltage Enhanced isolation voltage * DUAL 1-FORM-A POWER RELAY: BIDIRECTIONAL CPC2907B BI 60 2 - - DUAL power relay * 1-FORM-A POWER RELAYS: SINGLE-POLE - UNIDIRECTIONAL Part Number Relay Type Blocking Voltage (VP) CPC1706Y CPC1708J CPC1709J CPC1718J CPC1726Y CPC1727J CPC1777J CPC1779J CPC1786J CPC1788J UNI UNI UNI UNI UNI UNI UNI UNI UNI UNI 60 60 60 100 250 250 600 600 1000 1000 Load Current (A) Without Heat Sink 4 4 9 6.75 1 3.4 1.5 1.65 0.65 1 5C/W Heat Sink 11.85 22.8 17.5 8.6 4.6 4.12 1.75 2.45 On Resistance TC=25C 24 32 32 20 15 15 6.9 10.3 () 0.09 0.08 0.05 0.075 0.75 0.09 0.5 0.4 2 1.25 Features & Comments * 1-FORM-B POWER RELAY: SINGLE-POLE - UNIDIRECTIONAL CPC1705Y UNI 60 3.25 - - 0.09 5 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 Normally CLOSED power relay 15 OPTICALLY ISOLATED AC POWER SWITCHES * OPTICALLY ISOLATED AC POWER SWITCHES: LOAD CURRENT 1A Optically Isolated AC Power Switches * Blocking voltage from 400VP to 800VP * SCR-based AC power switches * Maximum load current up to 1Arms ZC Features: Applications: * Load current up to 1Arms * Blocking voltage up to 800VP * 5mA input sensitivity * Zero-cross turn on 1/2 Cycle * Low EMI and RFI generation * DC control, AC switching * Optically isolated * TTL and CMOS compatible * High noise immunity * Machine insertable, wave solderable Zero-Cross Turn-On * Programmable controls * Process control * Power control panels * Remote switching * Gas pump electronics * Large relay control circuits * Contactors * Solenoids * Motor controls * Heater controls 4-Pin DIP (16-Pin Body) Part Number Blocking Voltage Load Current (VP) (Arms) Input Control Current (mA) Operating Frequency Min / Max (Hz) Isolation Voltage Package Type CPC1943 400 0.5 5 20 - 500 3750 15, 16 CPC1945G CPC1945Y CPC1961 Dual 400 400 600 1 1 0.25 1 5 5 20 - 400 20 - 400 3750 3750 2 23 12 (Vrms) 5 20 - 500 3750 20, 22 CPC1963 600 0.5 5 20 - 500 3750 15, 16 CPC1965G 600 1 5 20 - 400 3750 2 CPC1965Y 600 1 5 20 - 400 3750 23 CPC1972 800 0.25 5 20 - 500 3750 12, 14 PD1201 400 1 5 20 - 500 3750 2 PD2401 500 1 5 20 - 500 3750 2 PD2601 600 1 5 20 - 500 3750 2 PM1204 400 0.5 5 20 - 500 3750 15, 16 PM1205 500 0.5 5 20 - 500 3750 15, 16 PM1206 600 0.5 5 20 - 500 3750 15, 16 PS1201 400 1 5 20 - 500 3750 23 PS2401 500 1 5 20 - 500 3750 23 PS2601 600 1 5 20 - 500 3750 23 1 Maximum continuous load current of a single pole or the sum of the load currents with both poles operating simultaneously. 16 2 6-Pin Surface Mount 6-Pin Power DIP 6-Pin DIP 14 15 6-Pin Power DIP Surface Mount 8-Pin DIP 16 20 8-Pin Surface Mount 22 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com 4-Pin SIP (8-Pin Body) 23 * OPTICALLY ISOLATED AC POWER SWITCHES: LOAD CURRENT >1A Metallized, external, Direct Copper Bond (DCB) surface for heat sink applications 29 - i4-PAC 36 - Power SIP 64 - SuperSIP 66 - Power SOIC turn-on (non-zero-cross) * Rapid Rapid turn-on devices turn on when the control input goes true regardless of the load voltage phase, and turn off when the load current crosses zero. Part Number Blocking Voltage (VP) CPC1964B 800 CPC1964BX6 600 CPC1966Y 600 CPC1966B 800 CPC1966BX8 800 CPC1966YX6 600 CPC1966YX8 800 CPC1976 600 CPC1976YX6 600 CPC1998J 800 CPC40055ST 800 ** Typical turn-on values. Load Current No Heat Sink (Arms) 1.5 1.5 3 3 3 3 3 2 2 5 5 5C/W Heat Sink (Arms) 20 20 TC=25C (Arms) 50 40 Input Control Current Input Control Voltage Operating Frequency Min / Max (mA) 5 5 5 5 5 5 5 5 5 5 5 (V) - (Hz) 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 20 - 500 Turn-On: Zero-Cross or Rapid Zero-cross Rapid Zero-cross Zero-cross Rapid Rapid Rapid Zero-cross Rapid Zero-cross Zero-cross * * * * * Switching Speed ton / toff Isolation Voltage Package Type (max) 1/2 Cycle 500s / 1/2 Cycle 1/2 Cycle 1/2 Cycle **45s / 1/2 Cycle 500s / 1/2 Cycle **45s / 1/2 Cycle 1/2 Cycle 500s / 1/2 Cycle 1/2 Cycle 1/2 Cycle (Vrms) 5000 5000 3750 5000 3750 3750 3750 3750 3750 2500 2500 66 66 36 66 66 36 36 36 36 29 64 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 Features Enhanced isolation voltage, 12.5mm creepage Rapid turn-on, enhanced isolation voltage Enhanced isolation voltage, 12.5mm creepage Rapid turn-on, 5.7mm creepage Rapid turn-on Rapid turn-on Rapid turn-on High load current High load current, 9.5mm creepage 17 Optically Isolated AC Power Switches * Blocking voltages of 600VP and 800V P * SCR-based AC power switches * Zero-cross and Rapid turn-on (non-zero-cross) versions MULTIFUNCTION PRODUCTS: SSR/OPTOCOUPLERS * GENERAL PURPOSE MULTIFUNCTION PRODUCTS (TELECOM MULTIFUNCTION PRODUCTS - PAGE 41) Multifunction Products: SSR/Optocouplers The OptoMOS line of Multifunction Products combines a number of discrete, optically isolated functions into a single package. These products mix and match solid state relays, optocouplers, and Darlington transistors to create highly functional circuits in a single, small package. Multifunction devices allow designers to consolidate circuit functions into a single device, thus freeing up valuable board space and reducing component count. Features: Applications: * 3750Vrms input-to-output isolation * Multiple functionality in a single package * Current limiting (part numbers with "L" suffix) * Machine insertable, wave solderable * TTL and CMOS compatible * Telecommunication/datacommunication * Instrumentation * I/O subsystems/electronic switching * Medical equipment (patient/equipment isolation) * Security * Aerospace * Industrial controls 4 20 21 22 16-Pin Low-Profile SOIC 8-Pin DIP 8-Pin Flatpack 8-Pin Surface Mount A B E Part Number IAA110 IAB110 IAD110 IBB110 TS117 TS117L TS118 TS120 TS190 TS190L XS170 18 Style B C A D E E F G E E E SSR Characteristics Blocking Voltage Current Handling On Resistance (VP) 350 350 350 350 350 350 350 350 400 400 350 (mA) 100 100 100 100 120 120 120 120 150 150 100 () 35 35 35 35 35 35 35 35 22 25 50 Optocoupler Characteristics Input Control Current (mA) 5 5 5 5 2 2 5 5 5 5 2 Breakdown Voltage (V) 20 20 20 20 20 20 20 20 20 20 20 Current Transfer Ratio (%) 33 33 33 33 33 33 33 300 33 33 33 Saturation Voltage (V) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.5 0.5 0.5 Input Control Current (mA) 6 6 6 6 6 6 6 2 6 6 6 Isolation Voltage C F D G Package Type Features and Comments 4 4 4 4 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 20, 21, 22 21 20, 22 Two 1-Form-A relays, one optocoupler One 1-Form-A relay, one 1-Form-B relay, one optocoupler One 1-Form-A relay, two optocouplers Two 1-Form-B relays, one optocoupler One 1-Form-A relay, one optocoupler One current-limiting 1-Form-A relay, one optocoupler One 1-Form-B relay, one optocoupler One 1-Form-A relay, one Darlington optocoupler One 1-Form-A relay, one optocoupler One current-limiting 1-Form-A relay, one optocoupler One 1-Form-A relay, one optocoupler (Vrms) 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 3750 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com FIELD EFFECT TRANSISTORS SOT-223 * N-CHANNEL DEPLETION MODE FETS SOT-89 Normally closed MOSFETs present low resistance with no power applied Ideal for security applications IGBT speed enhancement LED drivers Part Number Package Type SOT-23 V(BR)DSX ID RDS(on) VGS(off) VGS(off) Features & Comments (V) Min (mA) Max () Min (V) Max (V) CPC3701 60 600 1 -1.4 -3.1 SOT-89 CPC3703 250 360 4 -1.6 -3.9 SOT-89 CPC3708 350 130 14 -2 -3.6 SOT-89, SOT-223 CPC3710 250 220 10 -1.6 -3.9 SOT-89 CPC3714 350 240 14 -1.6 -3.9 SOT-89 CPC3720 350 130 22 -1.6 -3.9 SOT-89 CPC3730 350 140 35 -1.6 -3.9 SOT-89 CPC3902 250 400 2.5 -1.4 -3.1 SOT-89, SOT-223 CPC3909 400 300 6 -1.4 -3.1 SOT-89, SOT-223 CPC3960 600 100 44 -1.4 -3.1 SOT-223 CPC3980 800 100 45 -1.4 -3.1 SOT-223 CPC3982 800 20 380 -1.4 -3.1 SOT-23 Very small package CPC5602 350 130 14 -2 -3.6 SOT-223 Designed for use with LITELINK designs CPC5603 415 130 14 -2 -3.6 SOT-223 Designed for use with LITELINK designs Field Effect Transistors * * * * Features: * Normally closed depletion mode devices offer low RDS(on) at cold temperatures * Low on-resistance * High input impedance * Low VGS(off) voltage Applications: * Power fail switches * Discrete normally closed relays * Constant current, high brightness LED drivers * High voltage pre-regulators * Power inverters * Power supplies N-Channel Depletion Mode MOSFET as Pre-Regulator VAC Voltage Regulator VDC See Application Note AN-500 "Depletion-Mode Power MOSFETs and Applications" For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 19 IGBT & MOSFET GATE DRIVERS * LOW-SIDE GATE DRIVERS IGBT & MOSFET Gate Drivers Part Number Output Type IX4426 IX4427 IX4428 IXD_602 IX4423 IX4424 IX4425 IXD_604 IX4340 IXD_609 IXD_614 IXD_630 IXD_630M DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL DUAL SINGLE SINGLE SINGLE SINGLE IPEAK TC=25C (AP) 1.5 1.5 1.5 2 3 3 3 4 5 9 14 30 30 Output Resistance () 8 8 8 4 4 4 4 2.5 1.5 1 0.8 0.4 0.4 Available Logic Configurations I N F F, I, N I N F F, I, N, D D I, N, D I, N, D I, N, D I, N, D Enable Function * * * * * * Under-voltage Lockout (V) VCC < 3.8 VCC < 12.5 VCC < 9 Available Logic Configurations Enable Function Package Type Package Type IXD_604SI & SIA IXD_609SI IXD_614SI IX4340NE are AEC-Q100 qualified! Features: 54, 56 54, 56 54, 56 20, 53, 54, 56 54 54 54 20, 53, 54, 56 53, 54, 92 20, 53, 54, 56, 57, 58 20, 53, 57, 58 57, 58 57, 58 * 1.5A to 30A peak source/sink drive current * Wide operating voltage range * -40C to +125C extended operating temperature range * Logic input withstands negative swing of up to -5V * Matched rise and fall times * Low propagation delay time * Low output impedance Applications: * Efficient power MOSFET and IGBT switching * Switch mode power supplies * Motor controls * DC to DC converters * Class-D switching amplifiers * Pulse transformer driver AEC-Q100 Qualified Low-Side Gate Drivers Part Number Output Type IPEAK TC=25C (AP) Output Resistance () IXD_604SI DUAL 4 2.5 F, I, N, D * 53 IXD_604SIA DUAL 4 2.5 F, I, N, D * 54 IX4340NE DUAL 5 1.5 D * 53 IXD_609SI SINGLE 9 1 I, N, D * 53 IXD_614SI SINGLE 14 0.8 I, N, D * 53 8-Pin DIP 5-Pin TO-220 20 57 8-Pin Power SOIC 53 8-Pin SOIC ENA INA A OUTA INA A OUTA INA A OUTA INA 54 A OUTA B OUTB ENB 8-Pin DFN INB B OUTB INB F OUTB INB I IN 20 B B OUTB N OUT IN INB EN OUT IN 56 D 5-Pin TO-263 58 8-Pin MSOP 92 OUT For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com * IX2113: 600V HIGH-SIDE & LOW-SIDE GATE DRIVER * High-side channel can drive an N-channel power MOSFET or IGBT 600V from the common reference * Configured with independent high-side and low-side referenced output channels IX2113 VDD SD Input Control Logic & Cycle-by-Cycle Edge-Triggered Shutdown Pulse Generator High Voltage Level Shift LIN VSS UVLO R S R Q Buffer HO VS VCC UVLO Level Shift VDD / VCC VSS / COM Features: VB LS Delay Control Buffer * Floating channel for bootstrap operation up to 600V with an absolute maximum rating of 700V * Outputs capable of sourcing and sinking 2A * Gate drive supply range from 10V to 20V * Tolerant to negative voltage transients: dV/dt immune * 3.3V logic compatible * Under-voltage lockout for both high-side and low-side outputs * Matched propagation delays IGBT & MOSFET Gate Drivers HIN Level Shift VDD / VCC VSS / COM LO COM * IX21844: HIGH VOLTAGE HALF-BRIDGE GATE DRIVER * Programmable dead-time can be set between 400ns and 5s * Floating high-side channel can drive an N-channel power MOSFET or IGBT 600V from the common reference Features: * Floating channel for bootstrap operation to 600V with an absolute maximum rating of 700V * Outputs can source 1.4A and sink 1.8A * Gate drive supply range from 10V to 20V * Tolerant to negative voltage transients: dV/dt immune * 3.3V and 5V logic compatible * Under-voltage lockout for both high-side and low-side outputs * Matched propagation delays IX21844 Typical Application VCC HO IN IN VS SD SD VCC up to 600V VB LOAD DT Applications: * Switch mode power supplies * Motor driver inverters * DC/DC converters * Uninterruptable power supplies (UPS) RDT VSS COM VSS LO For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 21 * IX2120: 1200V HIGH AND LOW SIDE GATE DRIVER * Floating channel for bootstrap operation to +1200V * Outputs capable of sourcing and sinking 2A IX2120 Functional Block Diagram VB Features: VDD * Gate drive supply range from 15V to 20V * Enhanced robustness due to SOI process * Tolerant to negative voltage transients: dV/dt immune * 3.3V logic compatible * Undervoltage lockout for both high-side and low-side outputs HIN IGBT & MOSFET Gate Drivers Input Control Logic & Cycle-by-Cycle Edge-Triggered Shutdown SD Level Shift VDD / VCC VSS / COM Mid Voltage Level Shift Pulse Generator UVLO High Voltage Level Shift R S C Q Buffer HO VS VBM VSM UVLO LIN Level Shift VDD / VCC VSS / COM VSS LS Delay Control VCC Buffer LO COM * IX2127: 600V HIGH SIDE IGBT & MOSFET GATE DRIVER * Stable operation in high dV/dt noise environments * Outputs typically source 250mA and sink 500mA IX2127 Functional Block Diagram VCC Features: * Floating channel designed for bootstrap operation up to 600V * Tolerant to negative transient voltages; dV/dt immune * Under-voltage lockout * 3.3V, 5V, and 12V input logic compatible * Open-drain FAULT indicator pin shows over-current shutdown * Output in-phase with the input Low Side Buffer IN Data Latch Transmitter Low-High Level Shift HO Receiver Enable VS Blanking Signal 8-Pin DIP Applications: Delay FAULT * High speed gate driver * Motor drive inverter Q Enable R Receiver 8-Pin SOIC 22 VB Undervoltage Lockout High Side COM S High-Low Level Shift For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com Transmitter + Data Latch _ Comparator CS * IX3120: 2.5A OUTPUT OPTICALLY COUPLED GATE DRIVER IX3120 * 2.5A maximum peak output current * Wide operating voltage range: 15V to 30V Features: * 25kV/s minimum common-mode rejection (CMR) at 1500VCM * Under-voltage lockout with hysteresis * 3750Vrms input-to-output isolation * Wide temperature range: -40C to +100C N/C 1 8 VCC ANODE 2 7 VO CATHODE 3 6 VO N/C 4 5 VEE * Isolated IGBT/MOSFET gate drive * Switch mode power supplies * Industrial inverters * Motor drivers Ideally suited for use in motor control and inverter applications due to its low input LED current, high output peak current, and high noise immunity (25kV/s). * IX3180: 2.5A OUTPUT HI SPEED GATE DRIVER OPTOCOUPLER * 2.5A maximum peak output current * Wide operating voltage range: 10V to 20V IGBT & MOSFET Gate Drivers Applications: IX3180 N/C 1 8 VCC ANODE 2 7 VO CATHODE 3 6 VO N/C 4 5 VEE Features: * 200ns maximum propagation delay over temperature range * 20ns typical pulse width distortion * 10kV/s minimum common-mode rejection (CMR) at 1500VCM * Wide operating voltage range: 10V to 20V * Under-voltage lockout with hysteresis * 3750Vrms input-to-output isolation * Wide temperature range: -40C to +100C Applications: * High performance DC/DC converters * High performance switching power supplies * Motor control inverter applications * Motor drivers For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 23 * IX332B: 2.5 AMP OUTPUT CURRENT IGBT GATE DRIVER OPTOCOUPLER The IX332B is an advanced 2.5A output current, optically isolated, IGBT gate driver that integrates VCEdesaturation detection, UVLO fault status feedback, and active Miller clamping. The IX332B is constructed as a power optocoupler with 4250Vrms isolation between the control input and power output stages. In addition, an optically isolated, opencollector feedback circuit relays FAULT status to the controller. Both optical isolation circuits employ highly efficient infrared LEDs. Featuring soft IGBT turn-off, isolated fault feedback, under voltage lock-out with hysteresis, active Miller clamping, and VCE desaturation detection, the IX332B offers engineers design flexibility and maximum circuit protection. Features: IGBT & MOSFET Gate Drivers * Under Voltage Lock-Out Protection (UVLO) with Hysteresis * Floating outputs for parallel or series configuration * Desaturation Detection * "Soft" IGBT Turn-off * Miller Clamping * Open Collector Isolated fault feedback VCC2 11 14 VOUT UVLO ANODE 6,7 DRIVER NEW Applications: 13 ! CATHODE 5,8 DESAT DESAT 9,12 V EE VCLAMP * Isolated IGBT/Power MOSFET gate driver VCLAMP VE 3 FAULT VS 10 16 2 VCC1 1,4 15 VLED * OPTICALLY ISOLATED PHOTOVOLTAIC GATE DRIVERS * Dual optically isolated photovoltaic devices * Well suited for use in discrete solid state relay designs 8-Pin DIP Features: Input PV Output Input PV Output 8-Pin Surface Mount * Isolated 5.5V to 12V photovoltaic output * Floating outputs for parallel or series configuration Applications: Part Number FDA215 FDA217 24 Input Control Current (mA) 5 5 * MOSFET driver * Isolated floating power source Nominal Open-Circuit Voltage VOC (V) 5.5 11.75 Nominal Short-Circuit Current ISC (A) 2.5 4.5 Switching Speeds ton / toff (ms) 5/5 2 / 0.5 Isolation Voltage (Vrms) 3750 3750 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com Package Type 8-pin DIP, 8-pin surface mount 8-pin DIP, 8-pin surface mount * OPTICALLY ISOLATED LOAD-BIASED GATE DRIVERS * High speed, optically isolated gate driver ICs * Output driver powered from load voltage; no external power supply required * On-chip circuitry charges an external capacitor whose charge enables fast turn-on Features: CPC1590 Application Diagram 1 4 7 A NC * No external IC power supply * Low drive power requirements (TTL/CMOS compatible) * Load voltages up to 200V * Fast switching times - 40sec on, 400sec off CAP LOAD NC +VLOAD 8-Pin Flatpack CST RLED Applications: * Instrumentation * Multiplexers * I/O subsystems * Meters (Watt-Hour, water, gas) * Medical equipment (patient/equipment isolation) * Security * Aerospace * Industrial controls 5 G 2 3 Part Number CPC1580 CPC1590 6 B Input Control Current (mA) 2.5 2.5 -VLOAD Gate Voltage @ IF=5mA (VG) 7.5 - 12 7.5 - 12 IGBT & MOSFET Gate Drivers 8 VIN Blocking Voltage (VP) 65 200 Regulated Capacitor Voltage (VCAP-MAX) VDS - 0.2V 16 Switching Speeds ton / toff (s) 40 / 400 40 / 400 Isolation Voltage (Vrms) 3750 3750 * CPC1596: 570V OPTICALLY ISOLATED LOAD-BIASED GATE DRIVER Features: * Requires No Load-side Power Supply * Drives External Power MOSFET * Only 2.5mA Input LED Current to Drive External MOSFET * 3750Vrms Input-to-Output Isolation Applications: Optically Isolated AC or DC Relays for: * Industrial Controls * Instrumentation * Medical Equipment Isolation * Electronic Switching * I/O Subsystems * Appliances CPC1596 1 4 C 7 NC A 8 NC NEW CST ! G 5 Q1 LOAD + VLOAD 2 LED+ 3 Q2 B 6 LED- + VLOAD CPC1596 AC Application Circuit For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 25 HIGH VOLTAGE PRODUCTS * HIGH VOLTAGE ANALOG SWITCH ARRAYS Features: Applications: * Flexible high voltage supplies up to VPP - VNN=200V * Output switch on-resistance typically 20 * Low charge injection, low capacitance analog switches High Voltage Products Part Number Number of Channels Channel On-Resistance () Bleed Resistors (k) Clock Frequency (MHz) Turn-On Time (s) Turn-Off Time (s) Package Type CPC7220 8 20 - 5 5 5 50 CPC7232 CPC7601 CPC7701 8 16 16 21 25 25 20 - 50 20 - 50 5 8 8 5 5 5 5 5 5 50 50 50 CPC7220 8-BIT SHIFT REGISTER DIN DOUT LATCHES LEVEL SHIFTERS LATCHES LEVEL SHIFTERS VPP SW0 DOUT DIN DOUT D LE CL SW0 D LE CL SW2 L4 D LE CL CLK D LE CL SW3 D LE CL SW4 SW6 L7 D LE CL D LE CL SW7 VNN LEVEL SHIFTERS CPC7701 16-BIT SHIFT REGISTER SWITCHES L0 D LE CL LEVEL SHIFTERS VPP OUTPUT SWITCHES DIN SW0 DOUT D LE CL SW0 D LE CL SW1 D LE CL SW2 D LE CL SW3 D LE CL SW4 D LE CL SW5 D LE CL SW6 D LE CL SW15 SW1 L2 D LE CL SW2 CLK SW3 SW4 L5 D LE CL SW5 L6 D LE CL SW6 L15 D LE CL SW6 LATCHES VPP SW5 D LE CL LE LATCHES L4 D LE CL SW5 L6 D LE CL 50 L3 D LE CL SW2 D LE CL SW4 L5 D LE CL SW1 CLK SW3 48-Pin LQFP L1 D LE CL SW1 L2 D LE CL * Piezoelectric transducer drivers * Ultrasound imaging * Printers * Industrial controls and measurement CPC7601 16-BIT SHIFT REGISTER OUTPUT SWITCHES DIN L0 D LE CL L3 D LE CL CL CPC7232 8-BIT SHIFT REGISTER SWITCHES VPP L1 D LE CL CLK * Very low quiescent current: 30nA typical * -58dB off-isolation at 5MHz * Internal bleed resistors: CPC7232 & CPC7701 SW15 VNN CL LE D LE CL 8 Switches SW7 CL LE VNN RGND 16 Switches CL LE VNN 26 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com RGND * HIGH VOLTAGE ISOLATED ANALOG SWITCHES CPC7524: 600V Quad High Voltage Isolated Analog Switch Array * Provides flexible single-ended or differential access to high voltage networks * Configured as two sets of matched, paired switches for improved differential performance Features: Applications: * Switch voltage up to 600V * 110dB switch-to-switch isolation at 5kHz * Flexible switch configurations * Smart logic for power-up/hot-plug state control * 3.3V operation with very low power consumption * Switch current limiting and thermal shutdown protect against fault conditions * TTL logic-level inputs * Input latch * Matched RON * Clean, bounce-free switching * Monolithic IC reliability * 28-pin SOIC package * Instrumentation * Industrial controls and monitoring * Automatic test equipment (ATE) * Battery monitoring and charging circuits * Worldwide AC mains monitor High Voltage Products 28-Pin SOIC CPC7524 VDD = 3.3V S1* S1A S2* CHANNEL 1-2 S2A IN1 IN2 LATCH1-2 S1B S2B L A T C H 1-2 Channel 1-2 S1 Switch Control Logic S2 TSD1-2 * 600V S3* S3A CHANNEL 3-4 S4* S4A IN3 IN4 LATCH3-4 S3B S4B L A T C H 3-4 Channel 3-4 S3 Switch Control Logic S4 TSD3-4 DGND GND2 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 27 CPC7514: 320V Quad High Voltage Isolated Analog Switch Array * Provides single-ended or differential access to high voltage networks * Self-biasing - no external high-voltage supplies required High Voltage Products Features: Applications: * Low, matched RON * Switch voltage up to 320V * 320V logic-input-to-switch-output isolation * 110dB switch-to-switch isolation at 5kHz * Flexible switch configurations * Smart logic for power-up/hot-plug state control * 3.3V operation with very low power consumption * Switch current limiting protects against fault conditions * Thermal shutdown protects against fault conditions * Latched TTL logic level inputs * Clean, bounce-free switching * Monolithic IC reliability * Instrumentation * Industrial controls and monitoring * Automatic test equipment (ATE) * Battery charging circuits * Telephony VoIP gateways Central office (CO) and remote terminal (RT) Concentrators PBX systems Optical network terminals (ONT) Optical network units (ONU) Hybrid fiber coax (HFC) 20-Pin SOIC CPC7514 VDD = 3.3V S 1* S1A S2A IN1 IN2 LATCH1 TSD1 S2 * Channel 1-2 S1B S2B L A T C H 1 Channel 1-2 Switch Control Logic S1 S2 * 320V S 3* S3A Channel 3-4 S4A IN3 IN4 LATCH2 TSD2 28 S4 * S3B S4B L A T C H 2 Channel 3-4 Switch Control Logic S3 S4 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com CPC7512: 320V Dual Shunt-Isolated High Voltage High Frequency Analog Switch * Provides single-ended or differential access to high voltage networks * Self-biasing: no external high-voltage supplies required CPC7512 SW1A S1A Features: Applications: * Low, matched RON * Guaranteed break-before-make (BBM) * Switch voltage up to 320V * 60dB off-isolation at 1MHz * Smart logic for power-up/hot-plug state control * 5V operation with very low power consumption * Thermal shutdown protects against fault conditions * Latched TTL logic level inputs * Instrumentation * Industrial controls and monitoring * Multiplexed ultrasonic transducer switching * Automatic test equipment (ATE) * Battery monitoring and charging SW1B S1B SW1C S1COM L A T C H S1Sel0 S1Sel1 S1C Switch 1 Control Logic LATCH1 TSD SW2A SW2B S2A S2B S2COM S2C L A T C H S2Sel0 S2Sel1 20-Pin SOIC Switch 2 Control Logic LATCH2 Open A VS Insertion Loss = V +20 log S VM A VS B 50 C + VM Open Circuit = V +20 log M VS A VS B C 50 B C Crosstalk = VM + VM +20 log VS Open A B C Insertion Loss Into 50 Open Circuit Transfer Gain into 50 Transfer Gain (dB) Loss (dB) 2 4 6 8 -20 -20 -60 -80 -100 -120 10 1kHz 0 -40 100kHz 1MHz 10MHz Frequency 100MHz 1GHz 1.0E+03 -40 -60 -80 -100 -120 -140 10kHz + VM Crosstalk into 50 0 Transfer Gain (dB) 0 50 -140 1.0E+04 1.0E+05 1.0E+06 1.0E+07 1.0E+08 1kHz 10kHz Frequency (Hz) 1MHz 10MHz 100MHz Frequency For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service 100kHz +1 978 524 6768, +1 978 524 4900 29 High Voltage Products SW2C HIGH SPEED DIGITAL OPTICAL ISOLATORS * OPTICALLY ISOLATED IC BUS REPEATERS: CPC5902 & CPC5903 High Speed Digital Optical Isolators * * * * CPC5902 bidirectionally buffers clock and data signals CPC5903 bidirectionally buffers data signal, unidirectionally buffers clock signal Logic level translation for levels as low as 2.7V or as high as 5.5V Passes DC signals - no refresh clock needed - no clock noise generated CPC5902 Features: CPC5903 Features: * Bidirectionally buffers both I2C signals * Extends and isolates I2C interfaces * Supports standard and fast mode I2C (400kbps) * Side B fast-mode compliant: VDDB > 4.5V * Supports I2C clock stretching * No internal clock - low EM & RF generation * Operates on 2.7V to 5.5V * Supports DC logic level buffering without refresh * Glitch-free operation * Power down to Hi-Z does not load I2C bus * Slew-limited drivers reduce EMI * Immune to external EMI & RF emissions * High voltage isolation * Bidirectionally buffers SDA I2C signal * Side A extends and isolates I2C interfaces * Standard-mode and fast-mode I2C * Side B fast-mode compliant: VDDB > 4.5V * Operates on 2.7V to 5.5V * No internal clock - low EM & RF generation * Voltage level translation * Slew-limited drivers reduce EMI * Power down to Hi-Z does not load I2C bus * 3750Vrms galvanic isolation * Immune to external EMI & RF emissions * High voltage isolation CPC5902 VDDA I2C Master 30 I2C Slave CPC5902 GNDA VDDB VDDB Optical Isolation Barrier VDDA VDDA VDDB SCL_A SDA_A * Power-over-Ethernet (POE) * I2C bus length extender * Isolated control and signal monitoring * Power supply high-side interface * I2C logic level translation CPC5903 Optical al Isolation Barrier VDDA VDDA S "Op ee Appl tical i ly Is cation N olati ng a ote TB-1 n I 2C 01 Inter face Applications: " GNDB VDDA SCL_B SCL_A SDA_B SDA_A I2C Master I2C Slave I2C Master I2C Slave VDDB VDDB VDDB SCL_B CPC5903 GNDA For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com GNDB SDA_B I2C Slave I2C Slave * SINGLE-CHANNEL EACH DIRECTION DIGITAL OPTICAL ISOLATOR: CPC5001 CPC5001 VDDB 1 INA1 8 VDDA VDDB LED VDDB 2 GNDA B A VDDA B 7 OUTB1 6 GNDB 5 INB2 CHANNEL1 Features: Applications: * Isolates one signal in each direction * Operates from 2.7V to 5.5V * Buffered inputs - no external LED drive required * Hysteresis at inputs for noise rejection * Slew-limited drivers reduce EMI * 3750Vrms galvanic isolation from input to output * Power down to Hi-Z does not load outputs * 5 Mbaud data rate * Isolated signal monitoring and control * Power-over-Ethernet, POE * Power supply high-side interface * Logic level translation * Microprocessor system interface * Inter integrated circuit (I2C) interface * Serial peripheral interface * Full duplex communication * Isolated line receiver * Isolated data acquisition systems CHANNEL2 3 OUTA2 A VDDB B VDDA 4 VDDA LED A * DUAL HIGH SPEED DIGITAL OPTICAL ISOLATOR: CPC5002 CPC5002 * 3750Vrms galvanic isolation from input to output * Passes DC signals - no refresh clock needed Features: Applications: * Dual optics isolate two signals * 10 Mbaud data rate * Operates over 2.7V < VDD < 5.5V * Power down to Hi-Z does not load outputs * Low-power CMOS reduces supply current * LED drive current only 1.5mA * High speed: 10Mbaud typical * Isolated line receiver * Ground loop elimination * ADC/DAC digital noise isolation * 4-wire I2C bus isolation ANO1 1 8 VDD LED 2 7 3 6 CAT1 CAT2 OUT1 OUT2 LED 4 ANO2 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 5 GND 31 High Speed Digital Optical Isolators * Logic level translation for levels as low as 2.7V or as high as 5.5V * Passes DC signals - no refresh clock needed OPTOCOUPLERS * SINGLE & DUAL OPTOCOUPLERS * Single-transistor output or Darlington transistor output for higher current gain * Single-LED for unidirectional input signal or dual-LED input for bidirectional input signal * Input-to-output isolation: 1500Vrms, 3750Vrms, or 5000Vrms Features: * AC and DC compatible inputs * Machine insertable, wave solderable 10 12 4-Pin SOP 14 4 6-Pin Surface Mount 20 6-Pin DIP 88-Pin Pin DIP Applications: Part Number 22 42 8-Pin Surface Mount Minimum Breakdown Voltage (BVCEO) 30 350 350 30 30 30 30 30 30 Typical Current Transfer Ratio (%) 330 5500 5500 1000 300 300 350 8500 8500 Maximum Saturation Voltage (V) 0.3 1.2 1.2 0.5 0.5 0.5 0.5 1 1 Input Control Current (mA) 0.2 1 1 0.2 1 1 1 1 1 Minimum Isolation Voltage (Vrms) 1500 5000 3750 5000 3750 3750 3750 3750 3750 Package Type Configuration 10 42, 43 20, 22 42, 43 12, 14 12, 14 12, 14 12, 14 12, 14 A B I A E C C F D LDA200 30 300 0.5 1 3750 20, 22 L LDA201 LDA202 LDA203 LDA210 LDA211 LDA212 LDA213 30 30 30 30 30 30 30 300 300 300 8500 8500 8500 8500 0.5 0.5 0.5 1 1 1 1 1 1 1 1 1 1 1 3750 3750 3750 3750 3750 3750 3750 20, 22 20, 22 20, 22 20, 22 20, 22 20, 22 20, 22 K H G N M J I CPC1001N CPC1301 CPC1302 CPC1303 LDA100 LDA101 LDA102 LDA110 LDA111 32 43 3 4-Pin DIP 4-Pin Surface Mount A B 4-Pin Package Configurations Optocouplers * Modem switching (laptops, notebooks, PDAs) * Voltage detection * TIP/RING circuits * Ringing detection * Loop detection * Current sensing * Telecom switching C D E F 6-Pin Package G H I J K L M N For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com 8-Pin Package * LINEAR OPTOCOUPLERS * Input LED drives two photodiodes: (1) isolated output (2) feedback to correct for the input LED's non-linearity Features: Applications: * Couples analog & digital signals * 3750Vrms input-to-output isolation * Bandwidth >200kHz in photoconductive mode * Bandwidth 40kHz in photovoltaic mode * High gain stability * Low input-to-output capacitance * Low power consumption * 0.01% servo linearity * THD 87dB typical * Power supply feedback voltage/current * Medical sensor interfacing * Isolation of process control transducers * Isolated 4-20mA converters * Telephony isolation 16-Pin SOIC 4 8-Pin DIP Servo Gain K1=I1/IF (Min - Max) Forward Gain K2=I2/IF (Min - Max) Transfer Gain K3=K2/K1 (Min - Max) Input Control Current (mA) Isolation Voltage (Vrms) Package Type LOC110 0.004 - 0.03 0.004 - 0.03 0.668 - 1.179 2 - 10 3750 20, 21, 22 LOC111 LOC112 LOC117 LOC210 LOC211 0.008 - 0.03 0.004 - 0.03 0.008 - 0.03 0.004 - 0.03 0.008 - 0.03 0.006 - 0.03 0.004 - 0.03 0.006 - 0.03 0.004 - 0.03 0.006 - 0.03 0.733 - 1.072 0.733 - 1.072 0.887 - 1.072 0.773 - 1.072 0.773 - 1.072 2 - 10 2 - 10 2 - 10 2 - 10 2 - 10 3750 3750 3750 3750 3750 20, 21, 22 20, 21, 22 20, 21, 22 4 4 Photovoltaic Mode: * 14-bit linearity * 40kHz bandwidth 20 LOC21x - LED - LED + LED + LED C1 C2 C1 A1 A2 A1 8-Pin Flatpack C2 A2 21 - LED + LED C2 C1 A2 A1 8-Pin Surface Mount 22 Isolation Amplifier (Photovoltaic Mode) Two fundamental operating configurations: Photoconductive Mode: * Wide bandwidth (>200kHz) * 8-bit linearity LOC11x Optocouplers Part Number VCC VIN LOC110, LOC111 LOC112, or LOC117 IF - + I1 1 8 2 7 3 6 - 5 + VOUT 4 For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service I2 = K3I1 +1 978 524 6768, +1 978 524 4900 33 LIGHTING & DISPLAY PRODUCTS * HIGH VOLTAGE LED DRIVERS IX9907 Block Diagram IX9907: High Voltage, Dimmable LED Driver with PFC Control * Optimized for phase-cut dimmable, off-line LED applications * Multiple safety features ensure full system protection VCC ZCV Ringing Suppress Blanking Lighting & Display Products Reference Voltage Generator Features: * Internal 650V, 2 power MOSFET * Single stage, primary control with PFC and dimming features * >90% efficiency * >98% power factor * Wide operating voltage range * Digital soft start * Foldback correction and cycle-by-cycle peak current control * Output over-current and over-voltage protection * Over-temperature protection * Under-voltage lockout DRAIN Over-Voltage Protection Leading Edge Blanking Foldback Sense Amp SOURCE Over-Temp Sensor Soft-Start Control VR Shorted Winding Detection LPF Leading Edge Blanking Leading Edge Blanking PFC * Signage, decorative LED lighting * Flat-panel display RGB backlighting * DC & AC/DC LED driver applications GND Features: * 8V to 450V input voltage range * >90% efficiency * Drives multiple LEDs in series/parallel combinations * Regulated LED drive current * Linear or PWM brightness control inputs * Resistor-programmable oscillator frequency 34 Gate Control Control Logic Foldback Correction CS MXHV9910: High Voltage, Off-Line LED Driver VCC Monitor Over - Under Voltage Lockout IX9907, MXHV9910 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com Analog Mux CPC9909: High Efficiency, High Brightness Off-Line LED Driver * 8V to 550V input voltage range * Linear or PWM brightness control inputs * Drives multiple LEDs in series/parallel 8-Pin SOIC Features: * >90% efficiency * Stable operation at >50% duty cycle * Regulated LED current * Resistor-programmable minimum off-time * Drives external power MOSFET, enabling high LED output current applications * Buck or boost configuration IX9908 IX9908: High Voltage, Dimmable LED Driver with PFC Control * Ideal for quasi-resonant flyback LED bulb designs * Supports phase-cut dimming and power factor correction * Multiple safety features ensure full system protection Lighting & Display Products IX9908, CPC9909 T1 DVCC DOUT SNUBBER RZCV1 AC Features: - + Aux CIN * Single stage, primary control with PFC and dimming features * >90% efficiency * >98% power factor * Wide operating voltage range: up to 600V * Digital soft start * Cycle-by-cycle peak current control COUT CZCV CVCC RZCV2 VCC Q1 ZCV HV GD RIN2 VR GND CS CC RCS DVR CVR For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service LEDs IX9908 RIN1 +1 978 524 6768, +1 978 524 4900 35 TELECOMMUNICATIONS PRODUCTS * LITELINKTM SILICON DAA PHONE LINE INTERFACE Telecommunications Products * * * * * Industry's only single-package silicon Data Access Arrangement (DAA) Ideal for both voice and data (V.22bis to V.90/V.92) applications in particularly dense circuit environments Internal optical isolation barrier eliminates high-cost transformer or capacitive isolation circuits Saves cost through reduced passive component count and smaller printed circuit board space Available in a thin 32-pin SOIC surface mount package 32-Pin SOIC Part Number Isolation Voltage (Vrms) Power Supply (V) Caller ID Ringing Detect CPC5622 3000 CPC5621 CPC5620 3000 3000 3.3 - 5 Continuous Half-wave & full-wave 3.3 - 5 3.3 - 5 Selectable (CID=0) Selectable (CID=0) Full-wave (CID=1) Half-wave (CID=1) The 3kVrms internal isolation barrier exceeds all worldwide regulatory requirements. The LITELINK application circuit is capable of surviving 6kV (10sec x 700sec) lightning surge waveforms making it the most robust silicon DAA on the market. LITELINK offers the lowest operational phone line quiescent current. The device easily interfaces to commonly available standard single-ended or differential voice and modem codecs on the market. Contact IXYS Integrated Circuits for information on codec reference designs that offer programmable AC termination impedance for global applications. LITELINK complies with international PSTN agency requirements. CPC5622 Features: Applications: * Voice and data applications * Modem DAA for speeds up to V.92 * Half-wave or full-wave ringing detection * Worldwide telephone network compatibility * Caller-ID reception * Line side powered from telephone line * 3.3V to 5V power supply * Easy interface with modem ICs and voice codecs * High power transmit option for voice applications (>3dBm) * Small 32-pin SOIC package * Computer telephony * VoIP gateways * PBXs * Satellite set-top box * V.92 modems * Fax machines * Voice mail systems * Embedded modems * Vending machines * Automated banking * Remote metering * Surveillance * Security systems Isolation Barrier Tx+ Tx- Transmit Diff. Amplifier TIP Transmit Isolation Amplifier MODE OH RX Gain Trim Rx- Receive Diff. Amplifier RING Half Wave Rx+ RING2 Transconductance Stage 2-4 Wire Hybrid AC/DC Termination Hook Switch Receive Isolation Amplifier RING RX MUX & Ringing Det. Full Wave CSNOOP RSNOOP Snoop Amplifier Ringing Detect Outputs 36 TX Gain Trim For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com CSNOOP RSNOOP * SINGLE-CHANNEL VOICE-BAND CODEC: CPC5750 * -law and A-law ITU G.711 companding codec * Operates on +3.3V power * Differential analog signal paths * Programmable transmit and receive gain, +/-12dB in 0.1dB increments * Transmit path 60Hz rejection filter * Differential amplifier drives +3.2dBm into 600 * Stable gain over temperature * PCM and IOM-2 GCI telecommunication interfaces * Short and long frame syncs supported * Independent transmit and receive programmable time slots * Accepts PCLK from 512kHz to 8.192MHz * SPI serial interface for control in PCM mode * Programmable power down-mode, IDD = 20A * Analog and digital loopback modes for testing VDD D3 D2 Features: D1 D0 CPC5750 Block Diagram Control Register RST SPI Interface SCLK SDI SDO CS POR DLB + - AIN- ADC FIR Filter P-law/A-law Encoder VREF BAND GAP BUF PCM/IOM-2 Interface Logic 0.22PF VDD VEE Telecommunications Products AIN+ FS DTX DRX PCLK SFSEL BUF MUTE AOUT+ AOUT- + - Noise Shaper DAC FIR Filter m-law/A-law Decoder ALB * CALL PROGRESS TONE DETECTOR: M-980-02 * Detects common call progress tones including busy tone, dial tone, call waiting tones, and others * Operates on a 2.8V to 5.5V supply Features: Applications: * Receive common call progress tones * The M-980-02 operates with a single 2.8-5.5 volt supply * Linear input (detector) * Inexpensive band detector with wide dynamic range (>38dB) * Low power consumption * PBX circuits * Billing systems * Test equipment * Point-of-sale terminals M-980-02: Call Progress Tone Detector V SS V REF VDD Ref Gen Bandpass Filter SIGIN Level Sense Digital Control Detect 16-Pin SOIC Part Number M-980-02 Function (315 - 640Hz) Tone detector Osc Package Types XIN 16-pin SOIC, 8-pin DIP Clock Gen XOUT Enable 8-Pin DIP For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 37 * LINE CARD ACCESS SWITCHES (LCAS) 8 * Monolithic IC reliability * Impulse noise reduction * Low, matched on-resistance * Built-in zero-cross ringing switching * Small surface mount SOIC packages * Ultra-low power consumption of <10.5mW * Robust power-cross and lightning surge performance * Current limiting, thermal shutdown, and SLIC protection Telecommunications Products Applications: 32 * PBX systems * VoIP gateways * Channel banks * Pair gain systems * Central offices (CO) * Fiber in the loop (FITL) * Hybrid fiber coax (HFC) * Digital loop carriers (DLC) * Digitally added main line (DAML) 34 4 Switch - Ringing/Break Minimum 1500V/s dV/dt CPC7695xx CPC7594BA 10 Switch - Ringing/Break + Line Test/Test-Out + Test-In + Ringer Test 6 Switch - Ringing/Break + Channel Test/Test-In Optional Feature Ringing Return Test Out TIP Test In SCR and Trip Circuit 20-Pin SOIC RING SLIC Codec PCM Highway Break Ringing Access Test In 44-Pin TQFP Ringing Test Switch Pairs CPC7691BA CPC7691BB CPC7692BA CPC7692BC * * * * CPC7695xA CPC7695xB * * 10 10 CPC7695xC * 10 * * 4 4 6 * * * * * * 38 6 Switch - Ringing/Break + Line Test/Test Out Ringing Test Return 16-Pin SOIC # Switches 4 4 6 6 CPC7591BA CPC7591BB CPC7592BC CPC7591Bx CPC7691Bx Test Out 46 Part Number CPC7592Bx CPC7692Bx 28-Pin SOIC Features: Test Out Test In Ringing Test Break * * * * Ringing * * * * * * * * * * * * * * * * * * * * Zero-Cross Switching Protection Features * * * * Current Limit * * * * Diode Bridge * * * * Protection SCR * Minimum Hold Current (mA) 110 * * 110 110 * * * * * * * 110 Logic States Package Type 3 3 4 5 32 32 32 32 7 7 8, 34 8, 34 * * * * 110 8 8, 34 * * * * * * * * * * 110 * 110 3 3 5 32 32 32 For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com * LCAS FOR RINGING SLIC: CPC7508 Next generation LCAS device used with ringing SLICs Replaces the two 2-Form-C electromechanical test relays used in fiber-to-the-home and optical network deployments Provides TIP and RING line break, drop test, and channel test functionality CPC7508 Requires only a single +12V supply T (T ) TEST_IN Features: * TTL logic level inputs for 3.3V logic interfaces * Smart logic for power-up & hot-plug state control * Monolithic IC reliability * Low, matched RON * Clean, bounce-free switching * Tertiary protection consisting of integrated current limiting and thermal shutdown for SLIC protection Applications: CHAN_TEST +12VDC TTEST_OUT (TDROP_TEST) 1 VDD 8 7 X SW7 X SW3 Tip TLINE 6 X SW5 5 TBAT X SW1 Secondary Protection Ring Ringing SLIC SW2 RLINE 11 16-Pin SOIC X SW4 * Fiber to the home (FTTH) * Fiber in the loop (FITL) * VoIP gateways * PBX systems * Digitally added main line (DAML) * Hybrid fiber coax (HFC) 12 RBAT X X SW6 X RTEST_OUT (RDROP_TEST) 10 L A T C H Switch Control Logic SW8 9 2 GND 16 INA 15 INB 14 13 INC LATCH 3 TSD RTEST_IN (RCHAN_TEST) * CYBERGATETM DATA ACCESS ARRANGEMENT (DAA) MODULES * Completely functional V.34 DAA circuit in a 1.07" x 1.07" x 0.4" plastic module * Surge protection, transient protection Zener diodes, ringing detection, hook switch, gyrator, and a transformer * Caller-ID (CID) and loop current detection are also available as options Part Number Region Features Ringing Detection Full Wave CYG2000 CYG2011 CYG2020 CYG2100 CYG2110 CYG2111 CYG2217 CYG2218 CYG2320 N. America, Asia N. America, Asia N. America, Asia European Union Except France & Spain France CTR-21 N. America, Asia N. America, Asia Australia Half Wave Caller ID Loop Current Detect 2-4 Wire Conversion * * * * * Features: Applications: * 28.8kbps * Optional caller ID and loop current sense * Ringing detection * Low power hook switch * Surge protection * Gyrator circuitry * Meets most regulatory agency requirements * Modems * Remote data acquisition * Fax machines * Security/metering * Computer telephony * PBX * Voice mail systems * * * * * * * * Small Package Size! 1.07" x 1.07" x 0.4" 27.18mm x 27.18mm x 10.16mm For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 39 Telecommunications Products * * * * * DC TERMINATION ICS (XDSL, ISDN) CPC1465: SHDSL/ISDN * Polarity-insensitive DC termination for wetting (sealing) current on the CPE side * Conforms to ITU-T G.991.2 to eliminate corrosion on G.SHDSL/ISDN lines * Well controlled turn-on and turn-off minimizes injecting impulse noise into the G.SHDSL channel Features: Telecommunications Products * Integrated bridge rectifier for polarity correction * Uses inexpensive optocoupler for DC signaling * Electronic inductor, breakover, and latch circuits * Current limiting and excess power protection circuits * ANSI SHDSL and ISDN compatible * MLT and SARTS compatible * Excellent linearity (70dB typ.) CPC1465 & Application Circuit 16-Pin SOIC TIP Applications: * G.SHDSL * ISDN * Router and bridge customer premises equipment * Leased line equipment * T1/E1 network line cards and repeaters * Network termination 1 (NT1) equipment * Mechanized loop test (MLT) networks * Switched access remote test system (SARTS) networks RING 2.2k: 5% 4W 16-Pin DFN TC 16 NC 15 NC 14 RS 13 PD 12 NC NC 11 NC NC 10 1 PR+ 2 NC 3 NC 4 TIP 5 RING 6 7 8 Electronic Inductor, Breakover, Latch, and Opto Driver Bridge Rectifier DC Blocking Capacitor 1mF 68: 1% 1/4W Transceiver Current Limit and Excess PRPower Protection COM 9 VCC 1 6 2 5 3 4 75k: Digital Control Circuitry CPC1466: Broadband ADSL/VDSL * DC Termination IC for broadband ADSL/VDSL applications * Eliminates phone line corrosion on DSL twisted-pair, broadband-only lines Features: 1 PR+ 2 NC 3 TIP 4 NC CPC1466 Bridge Rectifier 16 NC 15 NC 14 RS 13 NC 12 * Meets wetting (sealing) current requirements per ITU-T G.992.3 * Integrated bridge rectifier for polarity correction * Uses inexpensive optocoupler for DC sealing current monitoring * Electronic inductor, breakover, and latch circuits * Current limiting and excess power protection circuits * ADSL/VDSL compatible with low-pass filter network * MLT and SARTS compatible * Compatible with portable test sets Applications: 5 NC 6 RING PD 11 7 NC NC 10 8 40 Electronic Inductor, Breakover, Latch, and Opto Driver TC Current Limit and Excess PRPower Protection COM 9 16-Pin DFN 16-Pin SOIC * ADSL/VDSL broadband modems * Router and bridge customer premises equipment * Leased line equipment * Mechanized loop test (MLT) networks * Switched access remote test systems (SARTS) networks For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com * TELECOM MULTIFUNCTION PRODUCTS (GENERAL PURPOSE MULTIFUNCTION PRODUCTS - PAGE 18) Multifunction devices allow designers to consolidate circuit functions into a single device, freeing up valuable board space and reducing component count. Designed specifically for the telecommunications industry, the Integrated Telecom Circuit (ITC) series is well suited for voice telephony and modem applications, providing most of the major functions required when designing DAA (Data Access Arrangement) or voice (FXO) line interface circuits. Available in a 16-pin SOIC package. (1-Form-A) PV Zener Protection Bidirectional Opto-Input (1-Form-A) (1-Form-A) PV PV * 3750Vrms input-to-output isolation * Multiple functionality in a single package * Current limiting (part numbers with "L" suffix) * Machine insertable, wave solderable * TTL and CMOS compatible Telecommunications Products Features: Zener Protection Unidirectional Opto-Input No Zener Protection Bidirectional Opto-Input 16-Pin SOIC Applications: ITC117(L) Part Number ITC117P ITC117PL ITC135P ITC137P ITC135 ITC137 Relay Parameters Blocking Voltage (VP) 350 350 350 350 Load Current (mA) 120 120 120 120 On Resistance () 15 20 15 15 * Telecommunication/datacommunication * Instrumentation * I/O subsystems * Electronic switching * Medical equipment (patient/equipment isolation) * Security * Aerospace * Industrial controls Optocoupler Parameters Input Control Current (mA) 5 5 5 5 Breakdown Voltage (V) 20 20 20 20 Current Transfer Ratio (%) 33 33 33 33 Saturation Voltage (V) 0.5 0.5 0.5 0.5 Input Control Current (mA) 6 6 6 6 Isolation Voltage Package Type Features 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC Full-wave ringing detect Full-wave ringing detect, current limiting Half-wave ringing detect Full-wave ringing detect (Vrms) 3750 3750 3750 3750 * LINE SENSE RELAY: M-949-11 CO PBX Switching Equipment M-949 Tip 2 + Ring 3 - - 1 + M-949-11 Balanced Dual Coil Telephone Line Current Sensing Relay * Senses telephone line current from 15mA to 200mA * Used by control circuitry for: On-hook/off-hook monitoring Switch hook flash detection Rotary dial pulse * Meets high isolation voltage requirement of 4000V * Meets UL and British Standard Specifications * Includes 1-Form-A relay contact + 4 6 - 5 LC Note: These relays are not polarity sensitive. The Positive and Negative indicators show the series-aiding coil configuration. Other Circuit (Dial Pulse Counter) DATA Strobe Off-hook For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 41 VOLTAGE MONITORING & SENSING ICS * VOLTAGE MONITORING DEVICES CPC5712 Voltage Monitoring & Sensing ICs * Special-purpose "Voltage Monitor with Detectors" integrated circuit used in high voltage telephony applications * Derives two voltage level detects, polarity information, and a scaled, linear representation of the phone line voltages * Non-telephony applications include instrumentation and industrial controls; virtually undetectable in use Features: V+ * 2 independent, programmable level-detectors with programmable hysteresis * Fixed-level polarity detector with hysteresis * Differential linear output * Excellent common-mode rejection ratio (CMRR) * Worldwide telephone network compatibility * Minimum external components * High differential input impedance, very low common-mode input impedance * Fixed gain, 3V to 5.5V operation 16-Pin 16 Pin SOP * Low power consumption * CMOS logic level output (TTL compatible) CPC5712 1 VCC RIN1 TIP OUT+ 5 7 IN+ + 8 IN- - RDIFF RING RIN2 G=5 OUT - 6 POLARITY 4 DET1 3 DET2 2 VREF GND Applications: * VoIP gateways, IP-PBX, xDSL * TIP/RING monitoring: polarity detection for caller ID, enhanced 911, line-in-use, battery detection, PSTN check 16 + Analog Output 15 14 VL1 9 VH1 10 R1 VL2 11 R2 R3 - Analog Output Polarity Output Voltage Level Detect 1 Voltage Level Detect 2 VH2 12 R4 13 R5 Resistors set the Voltage Level Detect Thresholds CPC5710 * Telephone line monitor circuit provides linear representation of phone line signal and a ringing detect signal * Ringing detect signal is set by external resistor network CPC5710 Features: * Differential or single-ended linear output * Full-wave ringing level detector comparator with internal threshold, large hysteresis, and TTL logic level output * High common-mode rejection ratio (CMRR) * Worldwide telephone network compatibility, virtually undetectable in use * High differential input impedance, very low common-mode input impedance * Fixed gain, 3.3V or 5.5V operation * CMOS logic level output (TTL compatible) VDD LIN/CMP 3 1 + 2 - VDD 1.625V VDD CMPOUT + IN+ IN- 6 + + AV=6 - - 7 0V 5 LINOUT+ 2V 4 LINOUT- Switch shown in Detector Mode 8-Pin SOIC Applications: VSS * Display feature (caller ID) signal buffering * Line-in-use detection (another-phone-off-hook) * Battery presence monitoring * TIP/RING voltage monitoring * Line polarity 42 VDD 50k: 8 + - For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com 1.25V GND GND * LOW VOLTAGE ERROR AMPLIFIER WITH A HIGH VOLTAGE DARLINGTON TRANSISTOR: IX9915 The IX9915 integrates an error amplifier with a precision reference and a 350V Darlington transistor in a single package. The error amplifier can be operated from 1.3V to 12.5V over the operational temperature range. The breakdown voltage of the Darlington transistor is 350V. Features: C * Precision reference, error amplifier, and a high voltage Darlington transistor in a single package * 1.299V1% reference @25C (1.5% @-40C to 85C) * Error amplifier supply voltage range: 1.3V to 12.5V over temperature * Breakdown voltage of Darlington transistor: 350V Applications: B OC VCC + _ VREF E + _ * LED lamps * Low voltage power supply feedback * AC-to-DC off-line power supplies * DC-to-DC converters VSS Dimmer Switch I3 Rectifier IH AC Supply - FB VREG R3 R0 IOC IQ I1 IX9915 Application Diagram +VLINE C B OC R1 VCC + _ E IX9915 FB + _ VREF The high voltage Darlington transistor will bleed the current when VLINE is lower than the predetermined voltage. The 4-terminal 431 type shunt regulator is used to monitor VLINE voltage and control the Darlington transistor bleeding the current (ON) or not (OFF). When VLINE reaches the predetermined voltage, the shunt regulator starts to regulate to drive VOC going low, and turns off the Darlington transistor to make sure this bleeder circuitry only burns a little power at the higher VLINE voltage. Maximum bleeding current IH can be controlled by properly choosing RE and VREG. R2 RE VSS For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 43 Voltage Monitoring & Sensing ICs The integrated combination of a 4-terminal 431 type shunt regulator with a high voltage Darlington transistor is ideal for use in LED lamp bleeder control circuits. * OPTICALLY ISOLATED ERROR AMPLIFIERS Optical Feedback for Ultra-Low-Voltage Power Supplies Features: * Low voltage operation: 1.6V: LIA135 & LIA136 2.7V: LIA120 & LIA130 * Optocoupler, precision reference, and error amplifier in a single package * LIA120: 70dB linearity typical VIN + LIA136 PWM Control Application: Voltage Monitoring & Sensing ICs * SMPS feedback loops * Power supply feedback C LED R1 E COMP 8-Pin DIP B 8-Pin Surface Mount FB + _ + _ Part Number Reference Voltage VREF Tolerance Isolation Voltage 25C (%) -40C to +85C (%) -40C to +110C (%) (Vrms) LIA120 1.240 1 2.5 - 3750 8-pin surface mount LIA130 LIA135 LIA136 1.240 1.299 1.299 1 0.5 0.5 1.5 1 - 1.5 3750 3750 3750 8-pin DIP, 8-pin surface mount 8-pin DIP, 8-pin surface mount 8-pin DIP, 8-pin surface mount LED C LED K C E COMP A E COMP LIA120 + _ GND GND LIA130 LIA135 K = Cathode, A = Anode C = Collector, E = Emitter, B = Base LED = LED Anode, COMP = Compensation, FB = Feedback, GND = Ground 44 B + _ FB + _ FB GND E COMP + _ GND C LED LED FB FB R2 GND Package Type (V) COMP VOUT + For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com LIA136 RFID PRODUCTS * RFID TAGS NCD1015ZP: Low Frequency, Half-Duplex, Robust 50mm Transponder * Read-only RFID device for single transponder applications in the area of electronic identification * Supports ISO 11784 and ISO 11785 standards Air interface Radio frequency center frequency Tag-to-reader transmission Tag-to-reader data rate On-chip 16-bit CRC generator Identification data * * * * * * Contact-less, sequential power & data transmission (HDX) 134.2 kHz FSK modulation, NRZ: "0" ~ 134.4kHz; "1" ~ 124.2kHz RF/16 (~8kbits/sec) Reverse CRC-CCITT as used in ISO/IEC 11785 64 bits data + 16 bits CRC mm 50 NCD1015M: Low Frequency, Half-Duplex RFID Integrated Circuit * HDX (R/W) RFID device for single transponder applications in the area of electronic identification * Supports ISO 11784/85 standards The NCD1015M contains an ASIC and 2 internal capacitors: one, a resonant capacitor, and the other a storage capacitor. The ASIC contains 3 memory blocks of 32 bits each, based on field programmable, non-volatile EEPROM. Each block contains 32 data bits. Blocks 1 and 2 are referred to as the 64-bit identification data page 1, which is secured by an associated 16-bit CRC. Block 0 offers the option to lock the RFID device. Once the device is locked, it is compatible with ISO 11784/85 standards. The HDX transponder IC receives Write-Block requests from the reader as a pulse interval encoded, 100% amplitude modulated data signal. Return data transmission from the transponder to the reader utilizes FSK encoded modulation. This is achieved by a serial data stream controlled Frequency Shift Keying (FSK) of the transponder's resonant circuit oscillation with an additional on-chip modulation capacitor between the two transponder terminals HF and GND. The passive transponder uses the supplied RF signal to obtain the energy needed to send the 64-bit ID code to the reader. Air interface Radio frequency center frequency Reader-to-tag transmission Tag-to-reader transmission Tag-to-reader data rate On-chip 16-bit CRC generator Identification data * * * * * * * Contact-less, sequential power & data transmission (HDX) 134.2 kHz typically Pulse interval encoding (PIE) ~1 to 2kBits/s FSK modulation, NRZ: "0" ~134.2kHz; "1" ~124.2kHz RF/16 (~8kbits/sec) Reverse CRC-CCITT as used in ISO/IEC 11785 64 bits data + 16 bits CRC For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 45 RFID Products The passive transponder uses the applied RF signal to obtain the energy needed to send the 64-bit ID code to the reader. Return data transmission from the transponder to the reader utilizes FSK encoded modulation. DIGITALLY PROGRAMMABLE CAPACITORS * WIDE CAPACITANCE RANGE, NON-VOLATILE, DIGITAL PROGRAMMABLE CAPACITOR: NCD2400M The NCD2400M is a dedicated electronic calibrator for oscillators, with reliable performance at 105C as required by OCXO applications. This product can be used in series or shunt configuration, to support a wide variety of tuning circuit topologies. Digitally Programmable Capacitors Digitally controlled capacitance trimming information is communicated via a 2-wire (I2C compatible) interface. The calibration value can be stored in the internal, re-programmable, non-volatile memory.. Features: * Operating frequency range of DC to 150MHz * 512-state digital programmable capacitor * Series and shunt configurations supported: Cshunt = 12.5pF to 194pF (15.6:1 tuning ratio) in discrete 355fF steps Cseries = 1.7pF to 194pF in discrete 376fF steps * Operation at 105C * 2-wire (I2C compatible) serial interface * EEPROM non-volatile memory * Wide power supply range (2.5 to 5.5V) * 2 x 2 x 0.65 mm 6-pin DFN package, MSL 1 SDA NCD2400M Functional Block Diagram VDD V+ V+ V+ Applications: * OCXOs * VCXOs * Crystal oscillators * Tunable RF stages * RFID tags * Industrial wireless control * Capacitor sensor trimming CP DIGITAL INTERFACE AND MEMORY SCL CN DFN package: 2mm x 2mm 46 C0 GND For data sheets, go to www.ixysic.com/Products/ProdList.htm IXYS Integrated Circuits - 78 Cherry Hill Drive - Beverly, MA USA 01915 - www.ixysic.com * NON-VOLATILE DIGITAL PROGRAMMABLE CAPACITOR: NCD2100 The NCD2100 is an EEPROM-based digitally programmable variable capacitor that provides capacitive offset trimming for capacitance sensitive circuits. Programming the non-volatile EEPROM register value or implementing on demand capacitance value changes are easily accomplished by means of the simple two-wire serial bus. Features: Digitally Programmable Capacitors Providing 1024 discrete capacitance values over a nominal value range of 6.6pF to 37.553pF with very small step sizes, the NCD2100 is well suited to ensure proper operation of capacitive critical circuits. Additionally, to ensure interoperability over a broad array of design environments, the device is rated for operation with supply voltages of 2.5V to 5.5V across the temperature range of -40C to +85C. Capacitance range: 6.6pF to 37.553pF * Operating frequency range 200kHz to 250MHz (contact the factory for operation at higher frequencies) * 1024 programmable capacitance values * Capacitance range 6.6pF to 37.553pF * Very small CDAC3 capacitance step size: 63fF * Operating temperature range: -40C to +85C * Operating supply voltage: 2.5V to 5.5V * Device size: 2mm x 2mm (DFN-6), 2.9mm x 2.8mm (TSOT-6) VDD NCD2100 CDAC1 X1 C0 Applications: * VCXOs * Crystal oscillators * Tunable RF stages * RFID tags * Industrial wireless control * Capacitor sensor trimming PV DIGITAL INTERFACE CDAC2 DFN package: 2mm x 2mm DA CDAC3 TSOT package: 2.8mm x 2.9mm CLK VSS For data sheets, go to www.ixysic.com/Products/ProdList.htm +1 978 524 6700, +1 978 524 4700 - Customer Service +1 978 524 6768, +1 978 524 4900 47 Worldwide Sales Offices AMERICAS EUROPE ASIA World Headquarters IXYS Integrated Circuits 78 Cherry Hill Drive Beverly, MA USA 01915-1048 European Customer Service Centre IXYS Semiconductor BV Schipholweg 103 2316 XC Leiden, Netherlands +1 978 524 6700 +1 978 524 4700 Toll-Free: 1 800 272 5273 0031-(0)71 3031500 0031-(0)71 3031509 E-mail: customerservice@ixys.de Littelfuse Far East Taiwan Rep. Office 8/F No. 181 Sec. 2 Tiding Blvd. Taipei 114 Taiwan CUSTOMER SERVICE +886 2 2523 6368 +886 2 87511234 ext. 101 E-mail: sales@ixysic.com.tw +1 978 524 6768 +1 978 524 4900 IXYS Integrated Circuits Copyright (c) December 2018, IXYS Integrated Circuits - All rights reserved. www.ixysic.com