LM3046
LM3046 Transistor Array
Literature Number: SNLS372A
LM3046
Transistor Array
General Description
The LM3046 consists of five general purpose silicon NPN
transistors on a common monolithic substrate. Two of the
transistors are internally connected to form a differentially-
connected pair. The transistors are well suited to a wide
variety of applications in low power system in the DC through
VHF range. They may be used as discrete transistors in
conventional circuits however, in addition, they provide the
very significant inherent integrated circuit advantages of
close electrical and thermal matching. The LM3046 is sup-
plied in a 14-lead molded small outline package.
Features
nTwo matched pairs of transistors
V
BE
matched ±5mV
Input offset current 2 µA max at I
C
=1mA
nFive general purpose monolithic transistors
nOperation from DC to 120 MHz
nWide operating current range
nLow noise figure: 3.2 dB typ at 1 kHz
Applications
nGeneral use in all types of signal processing systems
operating anywhere in the frequency range from DC to
VHF
nCustom designed differential amplifiers
nTemperature compensated amplifiers
Schematic and Connection
Diagram
Small Outline Package
00795001
Top View
Order Number LM3046M
See NS Package Number M14A
July 1999
LM3046 Transistor Array
© 2004 National Semiconductor Corporation DS007950 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications. (T
A
=
25˚C)
LM3046
Each Total Units
Transistor Package
Power Dissipation:
T
A
= 25˚C 300 750 mW
T
A
= 25˚C to 55˚C 300 750 mW
T
A
>55˚C Derate at 6.67 mW/˚C
T
A
= 25˚C to 75˚C mW
T
A
>75˚C mW/˚C
Collector to Emitter Voltage, V
CEO
15 V
Collector to Base Voltage, V
CBO
20 V
Collector to Substrate Voltage, V
CIO
(Note 2) 20 V
Emitter to Base Voltage, V
EBO
5V
Collector Current, I
C
50 mA
Operating Temperature Range −40˚C to +85˚C
Storage Temperature Range −65˚C to +85˚C
Soldering Information
Dual-In-Line Package Soldering (10 Sec.) 260˚C
Small Outline Package
Vapor Phase (60 Seconds) 215˚C
Infrared (15 Seconds) 220˚C
See AN-450 “Surface Mounting Methods and Their Effect on
Product Reliability” for other methods of soldering surface
mount devices.
Electrical Characteristics
(T
A
= 25˚C unless otherwise specified)
Parameter Conditions Limits Units
Min Typ Max
Collector to Base Breakdown Voltage (V
(BR)CBO
)I
C
= 10 µA, I
E
= 0 20 60 V
Collector to Emitter Breakdown Voltage (V
(BR)CEO
)I
C
= 1 mA, I
B
= 0 15 24 V
Collector to Substrate Breakdown I
C
= 10 µA, I
CI
= 0 20 60 V
Voltage (V
(BR)CIO
)
Emitter to Base Breakdown Voltage (V
(BR)EBO
)I
E
10 µA, I
C
=0 5 7 V
Collector Cutoff Current (I
CBO
)V
CB
= 10V, I
E
= 0 0.002 40 nA
Collector Cutoff Current (I
CEO
)V
CE
= 10V, I
B
= 0 0.5 µA
Static Forward Current Transfer V
CE
=3V I
C
=10mA 100
Ratio (Static Beta) (h
FE
)I
C
=1mA 40 100
I
C
=10µA 54
Input Offset Current for Matched V
CE
= 3V, I
C
= 1 mA 0.3 2 µA
Pair Q
1
and Q
2
|I
O1
−I
IO2
|
Base to Emitter Voltage (V
BE
)V
CE
=3V I
E
= 1 mA 0.715 V
I
E
= 10 mA 0.800
Magnitude of Input Offset Voltage for V
CE
= 3V, I
C
= 1 mA 0.45 5 mV
Differential Pair |V
BE1
−V
BE2
|
Magnitude of Input Offset Voltage for Isolated
Transistors |V
BE3
−V
BE4
|, |V
BE4
−V
BE5
|,
|V
BE5
−V
BE3
|
V
CE
= 3V, I
C
= 1 mA 0.45 5 mV
LM3046
www.national.com 2
Electrical Characteristics (Continued)
(T
A
= 25˚C unless otherwise specified)
Parameter Conditions Limits Units
Min Typ Max
Temperature Coefficient of Base to
Emitter Voltage
V
CE
= 3V, I
C
= 1 mA −1.9 mV/˚C
Collector to Emitter Saturation Voltage (V
CE(SAT)
)I
B
= 1 mA, I
C
= 10 mA 0.23 V
Temperature Coefficient of
Input Offset Voltage
V
CE
= 3V, I
C
= 1 mA 1.1 µV/˚C
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: The collector of each transistor is isolated from the substrate by an integral diode. The substrate (terminal 13) must be connected to the most negative point
in the external circuit to maintain isolation between transistors and to provide for normal transistor action.
Electrical Characteristics
Parameter Conditions Min Typ Max Units
Low Frequency Noise Figure (NF) f = 1 kHz, V
CE
= 3V, 3.25 dB
I
C
= 100 µA, R
S
=1kΩ
LOW FREQUENCY, SMALL SIGNAL EQUIVALENT CIRCUIT CHARACTERISTICS
Forward Current Transfer Ratio (h
fe
) f = 1 kHz, V
CE
= 3V, 110
I
C
=1mA
Short Circuit Input Impednace (h
ie
) 3.5 kΩ
Open Circuit Output Impedance (h
oe
) 15.6 µmho
Open Circuit Reverse Voltage Transfer Ratio (h
re
) 1.8x10
−4
ADMITTANCE CHARACTERISTICS
Forward Transfer Admittance (Y
fe
) f = 1 MHz, V
CE
= 3V, 31 − j 1.5
Input Admittance (Y
ie
)I
C
= 1 mA 0.3+J 0.04
Output Admittance (Y
oe
) 0.001+j 0.03
Reverse Transfer Admittance (Y
re
) See Curve
Gain Bandwidth Product (f
T
)V
CE
= 3V, I
C
= 3 mA 300 550
Emitter to Base Capacitance (C
EB
)V
EB
= 3V, I
E
= 0 0.6 pF
Collector to Base Capacitance (C
CB
)V
CB
= 3V, I
C
= 0 0.58 pF
Collector to Substrate Capacitance (C
CI
)V
CS
= 3V, I
C
= 0 2.8 pF
LM3046
www.national.com3
Typical Performance Characteristics
Typical Collector To Base
Cutoff Current vs Ambient
Temperature for Each
Transistor
Typical Collector To Emitter
Cutoff Current vs Ambient
Temperature for Each
Transistor
00795008 00795009
Typical Static Forward
Current-Transfer Ratio and
Beta Ratio for Transistors Q
1
and Q
2
vs Emitter Current
Typical Input Offset Current
for Matched Transistor Pair
Q
1
Q
2
vs Collector Current
00795010 00795011
Typical Static Base To Emitter
Voltage Characteristic and Input
Offset Voltage for Differential
Pair and Paired Isolated
Transistors vs Emitter Current
Typical Base To Emitter
Voltage Characteristic for
Each Transistor vs Ambient
Temperature
00795012 00795013
LM3046
www.national.com 4
Typical Performance Characteristics (Continued)
Typical Input Offset Voltage
Characteristics for Differential
Pair and Paired Isolated
Transistors vs Ambient
Temperature
Typical Noise Figure vs
Collector Current
00795014 00795015
Typical Noise Figure vs
Collector Current
Typical Noise Figure vs
Collector Current
00795016 00795017
LM3046
www.national.com5
Typical Performance Characteristics (Continued)
Typical Normalized Forward
Current Transfer Ratio, Short
Circuit Input Impedance,
Open Circuit Output Impedance,
and Open Circuit Reverse
Voltage Transfer Ratio vs
Collector Current
Typical Forward Transfer
Admittance vs Frequency
00795018
00795019
Typical Input Admittance
vs Frequency
Typical Output Admittance
vs Frequency
00795020 00795021
Typical Reverse Transfer
Admittance vs Frequency
Typical Gain-Bandwidth
Product vs Collector Current
00795022
00795023
LM3046
www.national.com 6
Physical Dimensions inches (millimeters)
unless otherwise noted
Molded Small Outline Package (M)
Order Number LM3046M
NS Package Number M14A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LM3046 Transistor Array
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
