L78 Datasheet Positive voltage regulator ICs Features TO-220 TO-220FP DPAK DPAK * * * * * * * Output current up to 1.5 A Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition SOA protection 2 % output voltage tolerance (A version) Guaranteed in extended temperature range (A version) Description The L78 series of three-terminal positive regulators is available in TO-220, TO-220FP, DPAK and DPAK packages and several fixed output voltages, making it useful in a wide range of applications. These regulators can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type embeds internal current limiting, thermal shut-down and safe area protection, making it essentially indestructible. If adequate heat sinking is provided, they can deliver over 1 A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltage and currents. Maturity status link L78 DS0422 - Rev 36 - September 2018 For further information contact your local STMicroelectronics sales office. www.st.com L78 Diagram 1 Diagram Figure 2. Block diagram GAMG220920161000MT DS0422 - Rev 36 page 2/55 L78 Pin configuration 2 Pin configuration Figure 3. Pin connections (top view) TO-220 TO-220FP DPAK DPAK GAMG220920161001MT Figure 4. Schematic diagram GAMG220920161002MT DS0422 - Rev 36 page 3/55 L78 Maximum ratings 3 Maximum ratings Table 1. Absolute maximum ratings Symbol Note: Parameter Value for VO= 5 to 18 V 35 for VO= 20, 24 V 40 VI DC input voltage IO Output current Internally limited PD Power dissipation Internally limited TSTG Storage temperature range TOP Operating junction temperature range Unit V -65 to 150 for L78xxC, L78xxAC C 0 to 125 for L78xxAB C -40 to 125 Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Table 2. Thermal data Symbol Parameter RthJC Thermal resistance junction-case RthJA Thermal resistance junction-ambient DPAK DPAK TO-220 TO-220FP Unit 3 8 5 5 C/W 62.5 100 50 60 C/W Figure 5. Application circuits GAMG220920161003MT DS0422 - Rev 36 page 4/55 L78 Test circuits 4 Test circuits Figure 6. DC parameter GAMG220920161004MT Figure 7. Load regulation GAMG220920161005MT Figure 8. Ripple rejection GAMG220920161006MT DS0422 - Rev 36 page 5/55 L78 Electrical characteristics 5 Electrical characteristics VI = 10 V, IO = 1 A, TJ = 0 to 125 C (L7805AC), TJ = -40 to 125 C (L7805AB), unless otherwise specified. Table 3. Electrical characteristics of L7805A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 4.9 5 5.1 V VO Output voltage IO = 5 mA to 1 A, VI = 7.5 to 18 V 4.8 5 5.2 V VO Output voltage IO = 1 A, VI = 18 to 20 V, TJ = 25 C 4.8 5 5.2 V VI = 7.5 to 25 V, IO = 500 mA, TJ = 25 C 7 50 mV VI = 8 to 12 V 10 50 mV VI = 8 to 12 V, TJ = 25 C 2 25 mV VI = 7.3 to 20 V, TJ = 25 C 7 50 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 8 50 TJ = 25 C 4.3 6 mA 6 mA VI = 8 to 23 V, IO = 500 mA 0.8 mA VI = 7.5 to 20 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 8 to 18 V, f = 120 Hz, IO = 500 mA 68 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B =10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 17 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -1.1 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 6/55 L78 Electrical characteristics VI = 11 V, IO = 1 A, TJ = 0 to 125 C (L7806AC), TJ = -40 to 125 C (L7806AB), unless otherwise specified. Table 4. Electrical characteristics of L7806A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 5.88 6 6.12 V VO Output voltage IO = 5 mA to 1 A, VI = 8.6 to 19 V 5.76 6 6.24 V VO Output voltage IO = 1 A, VI = 19 to 21 V, TJ = 25 C 5.76 6 6.24 V VI = 8.6 to 25 V, IO = 500 mA, TJ = 25 C 9 60 mV VI = 9 to 13 V 11 60 mV VI = 9 to 13 V, TJ = 25 C 3 30 mV VI = 8.3 to 21 V, TJ = 25 C 9 60 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.3 6 mA 6 mA VI = 9 to 24 V, IO = 500 mA 0.8 mA VI = 8.6 to 21 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 9 to 19 V, f = 120 Hz, IO = 500 mA 65 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B =10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 17 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -0.8 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 7/55 L78 Electrical characteristics VI = 14 V, IO = 1 A, TJ = 0 to 125 C (L7808AC), TJ = -40 to 125 C (L7808AB), unless otherwise specified. Table 5. Electrical characteristics of L7808A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 7.84 8 8.16 V VO Output voltage IO = 5 mA to 1 A, VI = 10.6 to 21 V 7.7 8 8.3 V VO Output voltage IO = 1 A, VI = 21 to 23 V, TJ = 25 C 7.7 8 8.3 V VI = 10.6 to 25 V, IO = 500 mA, TJ = 25 C 12 80 mV VI = 11 to 17 V 15 80 mV VI = 11 to 17 V, TJ = 25 C 5 40 mV VI = 10.4 to 23 V, TJ = 25 C 12 80 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.3 6 mA 6 mA VI = 11 to 23 V, IO = 500 mA 0.8 mA VI = 10.6 to 23 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 11.5 to 21.5 V, f = 120 Hz, IO = 500 mA 62 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B =10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 18 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -0.8 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 8/55 L78 Electrical characteristics VI = 15 V, IO = 1 A, TJ = 0 to 125 C (L7809AC), TJ = -40 to 125 C (L7809AB), unless otherwise specified(Minimum load current for regulation is 5 mA.) Table 6. Electrical characteristics of L7809A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 8.82 9 9.18 V VO Output voltage IO = 5 mA to 1 A, VI = 10.6 to 22 V 8.65 9 9.35 V VO Output voltage IO = 1 A, VI = 22 to 24 V, TJ = 25 C 8.65 9 9.35 V VI = 10.6 to 25 V, IO = 500 mA, TJ = 25 C 12 90 mV VI = 11 to 17 V 15 90 mV VI = 11 to 17 V, TJ = 25 C 5 45 mV VI = 11.4 to 23 V, TJ = 25 C 12 90 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.3 6 mA 6 mA VI = 11 to 25 V, IO = 500 mA 0.8 mA VI = 10.6 to 23 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 11.5 to 21.5 V, f = 120 Hz, IO = 500 mA 61 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B =10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 18 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -0.8 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 9/55 L78 Electrical characteristics VI = 19 V, IO = 1 A, TJ = 0 to 125 C (L7812AC), TJ = -40 to 125 C (L7812AB), unless otherwise specified. Table 7. Electrical characteristics of L7812A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 11.75 12 12.25 V VO Output voltage IO = 5 mA to 1 A, VI = 14.8 to 25 V 11.5 12 12.5 V VO Output voltage IO = 1 A, VI = 25 to 27 V, TJ = 25 C 11.5 12 12.5 V VI = 14.8 to 30 V, IO = 500 mA, TJ = 25 C 13 120 mV VI = 16 to 12 V 16 120 mV VI = 16 to 12 V, TJ = 25 C 6 60 mV VI = 14.5 to 27 V, TJ = 25 C 13 120 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.4 6 mA 6 mA VI = 15 to 30 V, IO = 500 mA 0.8 mA VI = 14.8 to 27 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq DIq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 15 to 25 V, f = 120 Hz, IO = 500 mA 60 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B = 10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 18 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -1 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 10/55 L78 Electrical characteristics VI = 23 V, IO = 1 A, TJ = 0 to 125 C (L7815AC), TJ = -40 to 125 C (L7815AB), unless otherwise specified. Table 8. Electrical characteristics of L7815A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 14.7 15 15.3 V VO Output voltage IO = 5 mA to 1 A, VI = 17.9 to 28 V 14.4 15 15.6 V VO Output voltage IO = 1 A, VI = 28 to 30 V, TJ = 25 C 14.4 15 15.6 V VI = 17.9 to 30 V, IO = 500 mA, TJ = 25 C 13 150 mV VI = 20 to 26 V 16 150 mV VI = 20 to 26 V, TJ = 25 C 6 75 mV VI = 17.5 to 30 V, TJ = 25 C 13 150 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.4 6 mA 6 mA VI = 17.5 to 30 V, IO = 500 mA 0.8 mA VI = 17.5 to 30 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz, IO = 500 mA 58 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B = 10Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 19 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -1 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 11/55 L78 Electrical characteristics VI = 33 V, IO = 1 A, TJ = 0 to 125 C (L7824AC), TJ = -40 to 125 C (L7824AB), unless otherwise specified. Table 9. Electrical characteristics of L7824A Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 23.5 24 24.5 V VO Output voltage IO = 5 mA to 1 A, VI = 27.3 to 37 V 23 24 25 V VO Output voltage IO = 1 A, VI = 37 to 38 V, TJ = 25 C 23 24 25 V VI = 27 to 38 V, IO = 500 mA, TJ = 25 C 31 240 mV VI = 30 to 36 V 35 200 mV VI = 30 to 36 V, TJ = 25 C 14 120 mV VI = 26.7 to 38 V, TJ = 25 C 31 240 mV IO = 5 mA to 1 A 25 100 IO = 5 mA to 1.5 A, TJ = 25 C 30 100 IO = 250 to 750 mA 10 50 TJ = 25 C 4.6 6 mA 6 mA VI = 27.3 to 38 V, IO = 500 mA 0.8 mA VI = 27.3 to 38 V, TJ = 25 C 0.8 mA IO = 5 mA to 1 A 0.5 mA VO (1) VO (1) Iq Iq Line regulation Load regulation Quiescent current Quiescent current change mV SVR Supply voltage rejection VI = 28 to 38 V, f = 120 Hz, IO = 500 mA 54 dB Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V eN Output noise voltage TA = 25 C, B = 10 Hz to 100 kHz 10 V/VO RO Output resistance f = 1 kHz 20 m Isc Short circuit current VI = 35 V, TA = 25 C 0.2 A Iscp Short circuit peak current TJ = 25 C 2.2 A VO/T Output voltage drift -1.5 mV/C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 12/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 10 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 10. Electrical characteristics of L7805C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 4.8 5 5.2 V VO Output voltage IO = 5 mA to 1 A, VI = 7 to 18 V 4.75 5 5.25 V VO Output voltage IO = 1 A, VI = 18 to 20V, TJ = 25 C 4.75 5 5.25 V VO (1) Line regulation VI = 7 to 25 V, TJ = 25 C 3 100 VI = 8 to 12 V, TJ = 25 C 1 50 VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1.1 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 40 V/VO SVR Supply voltage rejection VI = 8 to 18 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 17 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.75 A Iscp Short circuit peak current TJ = 25 C 2.2 A IO = 5 mA to 1.5 A, TJ = 25 C 100 IO = 250 to 750 mA, TJ = 25 C 50 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 7 to 23 V 0.8 62 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 13/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 11 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 11. Electrical characteristics of L7806C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 5.75 6 6.25 V VO Output voltage IO = 5 mA to 1 A, VI = 8 to 19 V 5.7 6 6.3 V VO Output voltage IO = 1 A, VI = 19 to 21 V, TJ = 25 C 5.7 6 6.3 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current DId Quiescent current change VO/T Output voltage drift IO = 5 mA -0.8 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 45 V/VO SVR Supply voltage rejection VI = 9 to 19 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 19 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.55 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 8 to 25 V, TJ = 25 C 120 VI = 9 to 13 V, TJ = 25 C 60 IO = 5 mA to 1.5 A, TJ = 25 C 120 IO = 250 to 750 mA, TJ = 25 C 60 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 8 to 24 V 1.3 59 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 14/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 14 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 12. Electrical characteristics of L7808C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 7.7 8 8.3 V VO Output voltage IO = 5 mA to 1 A, VI = 10.5 to 21 V 7.6 8 8.4 V VO Output voltage IO = 1 A, VI = 21 to 25 V, TJ = 25 C 7.6 8 8.4 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -0.8 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 52 V/VO SVR Supply voltage rejection VI = 11.5 to 21.5 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 16 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.45 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 10.5 to 25 V, TJ = 25 C 160 VI = 11 to 17 V, TJ = 25 C 80 IO = 5 mA to 1.5 A, TJ = 25 C 160 IO = 250 to 750 mA, TJ = 25 C 80 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 10.5 to 25 V 1 56 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 15/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 14.5 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 13. Electrical characteristics of L7885C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 8.2 8.5 8.8 V VO Output voltage IO = 5 mA to 1 A, VI = 11 to 21.5 V 8.1 8.5 8.9 V VO Output voltage IO = 1 A, VI = 21.5 to 26 V, TJ = 25 C 8.1 8.5 8.9 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -0.8 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 55 V/VO SVR Supply voltage rejection VI = 12 to 22 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 16 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.45 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 11 to 27 V, TJ = 25 C 160 VI = 11.5 to 17.5 V, TJ = 25 C 80 IO = 5 mA to 1.5 A, TJ = 25 C 160 IO = 250 to 750 mA, TJ = 25 C 80 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 11 to 26 V 1 56 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 16/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 15 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 14. Electrical characteristics of L7809C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 8.64 9 9.36 V VO Output voltage IO = 5 mA to 1 A, VI = 11.5 to 22 V 8.55 9 9.45 V VO Output voltage IO = 1 A, VI = 22 to 26 V, TJ = 25 C 8.55 9 9.45 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 70 V/VO SVR Supply voltage rejection VI = 12 to 23 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 17 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.40 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 11.5 to 26 V, TJ = 25 C 180 VI = 12 to 18 V, TJ = 25 C 90 IO = 5 mA to 1.5 A, TJ = 25 C 180 IO = 250 to 750 mA, TJ = 25 C 90 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 11.5 to 26 V 1 55 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 17/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 19 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 15. Electrical characteristics of L7812C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 11.5 12 12.5 V VO Output voltage IO = 5 mA to 1 A, VI = 14.5 to 25 V 11.4 12 12.6 V VO Output voltage IO = 1 A, VI = 25 to 27 V, TJ = 25 C 11.4 12 12.6 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 75 V/VO SVR Supply voltage rejection VI = 15 to 25 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 18 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.35 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 14.5 to 30 V, TJ = 25 C 240 VI = 16 to 22 V, TJ = 25 C 120 IO = 5 mA to 1.5 A, TJ = 25 C 240 IO = 250 to 750 mA, TJ = 25 C 120 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 14.5 to 30 V 1 55 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 18/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 23 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 16. Electrical characteristics of L7815C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 14.4 15 15.6 V VO Output voltage IO = 5 mA to 1 A, VI = 17.5 to 28 V 14.25 15 15.75 V VO Output voltage IO = 1 A, VI = 28 to 30 V, TJ = 25 C 14.25 15 15.75 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1 mV/C eN Output noise voltage B = 10 Hz to 100kHz, TJ = 25 C 90 V/VO SVR Supply voltage rejection VI = 18.5 to 28.5 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 19 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.23 A Iscp Short circuit peak current TJ = 25 C 2.2 A VI = 17.5 to 30 V, TJ = 25 C 300 VI = 20 to 26 V, TJ = 25 C 150 IO = 5 mA to 1.5 A, TJ = 25 C 300 IO = 250 to 750 mA, TJ = 25 C 150 TJ = 25 C 8 IO = 5 mA to 1A 0.5 VI = 17.5 to 30 V 1 54 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 19/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 26 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 17. Electrical characteristics of L7818C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 17.3 18 18.7 V VO Output voltage IO = 5 mA to 1 A, VI = 21 to 31 V 17.1 18 18.9 V VO Output voltage IO = 1 A, VI = 31 to 33 V, TJ = 25 C 17.1 18 18.9 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 110 V/VO SVR Supply voltage rejection VI = 22 to 32 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 22 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.20 A Iscp Short circuit peak current TJ = 25 C 2.1 A VI = 21 to 33 V, TJ = 25 C 360 VI = 24 to 30 V, TJ = 25 C 180 IO = 5 mA to 1.5 A, TJ = 25 C 360 IO = 250 to 750 mA, TJ = 25 C 180 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 21 to 33 V 1 53 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 20/55 L78 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 C, VI = 33 V, IO = 500 mA, CI = 0.33 F, CO = 0.1 F unless otherwise specified. Table 18. Electrical characteristics of L7824C Symbol Parameter Test conditions Min. Typ. Max. Unit VO Output voltage TJ = 25 C 23 24 25 V VO Output voltage IO = 5 mA to 1 A, VI = 27 to 37 V 22.8 24 25.2 V VO Output voltage IO = 1 A, VI = 37 to 38 V, TJ = 25 C 22.8 24 25.2 V VO (1) Line regulation VO (1) Load regulation Id Quiescent current Id Quiescent current change VO/T Output voltage drift IO = 5 mA -1.5 mV/C eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C 170 V/VO SVR Supply voltage rejection VI = 28 to 38 V, f = 120 Hz Vd Dropout voltage IO = 1 A, TJ = 25 C 2 V RO Output resistance f = 1 kHz 28 m Isc Short circuit current VI = 35 V, TJ = 25 C 0.15 A Iscp Short circuit peak current TJ = 25 C 2.1 A VI = 27 to 38 V, TJ = 25 C 480 VI = 30 to 36 V, TJ = 25 C 240 IO = 5 mA to 1.5 A, TJ = 25 C 480 IO = 250 to 750 mA, TJ = 25 C 240 TJ = 25 C 8 IO = 5 mA to 1 A 0.5 VI = 27 to 38 V 1 50 mV mV mA mA dB 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. Note: DS0422 - Rev 36 Minimum load current for regulation is 5 mA. page 21/55 L78 Application information 6 Application information 6.1 Design consideration The L78 Series of fixed voltage regulators are designed with thermal overload protection that shuts down the circuit when subjected to an excessive power overload condition, internal short-circuit protection that limits the maximum current the circuit will pass, and output transistor safe-area compensation that reduces the output shortcircuit current as the voltage across the pass transistor is increased. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with capacitor if the regulator is connected to the power supply filter with long lengths, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good high frequency characteristics to insure stable operation under all load conditions. A 0.33 F or larger tantalum, mylar or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. The addition of an operational amplifier allows adjustment to higher or intermediate values while retaining regulation characteristics. The minimum voltage obtained with the arrangement is 2 V greater than the regulator voltage. The circuit of Figure 14. High current voltage regulator can be modified to provide supply protection against short circuit by adding a short circuit sense resistor, RSC, and an additional PNP transistor. The current sensing PNP must be able to handle the short circuit current of the three terminal regulator Therefore a four ampere plastic power transistor is specified. Figure 9. Fixed output regulator GAMG220920161007MT 1. 2. DS0422 - Rev 36 Although no output capacitor is need for stability, it does improve transient response. Required if regulator is located an appreciable distance from power supply filter. page 22/55 L78 Design consideration Figure 10. Current regulator IO = VXX/R1+Id GAMG220920161008MT Figure 11. Circuit for increasing output voltage IR1 5 Id VO = VXX(1+R 2 /R1)+ I dR2 GAMG220920161009MT Figure 12. Adjustable output regulator (7 to 30 V) GAMG220920161010MT DS0422 - Rev 36 page 23/55 L78 Design consideration Figure 13. 0.5 to 10 V regulator VO =VXXR 4 /R 1 GAMG220920161011MT Figure 14. High current voltage regulator VBEQ1 R1 = ______________ I REQ-(I Q1/bQ1) VBEQ1 I O = I REG + Q1 (I REG _____ _) R1 GAMG220920161012MT Figure 15. High output current with short circuit protection RSC =VBEQ2/ISC GAMG220920161013MT DS0422 - Rev 36 page 24/55 L78 Design consideration Figure 16. Tracking voltage regulator GAMG220920161014MT Figure 17. Split power supply ( 15 V - 1 A) GAMG220920161015MT Note: DS0422 - Rev 36 * Against potential latch-up problems. page 25/55 L78 Design consideration Figure 18. Negative output voltage circuit GAMG220920161016MT Figure 19. Switching regulator GAMG220920161017MT Figure 20. High input voltage circuit (configuration 1) VIN = VI - (VZ + VBE) GAMG220920161018MT DS0422 - Rev 36 page 26/55 L78 Design consideration Figure 21. High input voltage circuit (configuration 2) GAMG220920161019MT Figure 22. High input and output voltage VO = VXX + VZ1 GAMG220920161020MT Figure 23. Reducing power dissipation with dropping resistor VI(min)-VXX-VDROP(max) R = ____________________ IO(max)+Id(max) GAMG220920161021MT DS0422 - Rev 36 page 27/55 L78 Design consideration Figure 24. Remote shutdown GAMG220920161022MT Figure 25. Power AM modulator (unity voltage gain, IO 0.5) GAMG220920161023MT Note: The circuit performs well up to 100 kHz. Figure 26. Adjustable output voltage with temperature compensation VO = VXX (1+R2/R1) + VBE GAMG220920161024MT Note: DS0422 - Rev 36 Q2 is connected as a diode in order to compensate the variation of the Q1 VBE with the temperature. C allows a slow rise time of the VO. page 28/55 L78 Design consideration Figure 27. Light controllers (VO(min) = VXX + VBE) VO falls when the light goes up VO rises when the light goes up GAMG220920161025MT Figure 28. Protection against input short-circuit with high capacitance loads GAMG220920161026MT Note: DS0422 - Rev 36 Application with high capacitance loads and an output voltage greater than 6 volts need an external diode (see Figure 23. Reducing power dissipation with dropping resistor) to protect the device against input short circuit. In this case the input voltage falls rapidly while the output voltage decrease slowly. The capacitance discharges by means of the base-emitter junction of the series pass transistor in the regulator. If the energy is sufficiently high, the transistor may be destroyed. The external diode by-passes the current from the IC to ground. page 29/55 L78 Typical performance 7 Typical performance Figure 29. Dropout voltage vs junction temperature VI-Vo (V) Io(A) L78XX IO = 1 2 0m IO = 0 mA 2 A IO = 200 1 L7805 2.5 A IO = 50 1.5 Figure 30. Peak output current vs input/output differential voltage Tj = Tj = mA IO = 20 m A 1.5 Tj = Tj 1 =1 50 55 0 C C 12 Tj 5 C =2 5 C C DROPOUT CONDITIONS VO = 5% of VO 0.5 0.5 0 -75 -50 -25 0 25 50 75 100 125 Tj (C) 0 5 15 10 20 Vi-VO (V) GAMG200920161324MT GAMG200920161325MT Figure 31. Supply voltage rejection vs frequency 25 Figure 32. Output voltage vs junction temperature Vo (V) SVR (dB) L7812 L7805 80 Vi = 19 V Vo = 12 V Io = 20 mA 12.1 60 12.0 40 11.9 Vi = 8 V to 18 V Vo = 5 V Io = 500 mA Tj = 25 C 20 0 10 102 103 11.8 104 f (Hz) GAMG200920161322MT DS0422 - Rev 36 -75 -50 -25 0 25 50 75 100 125 Tj (C) GAMG200920161323MT page 30/55 L78 Typical performance Figure 33. Output impedance vs frequency Figure 34. Quiescent current vs junction temp. Id (mA) Zo () L7805 10 Vi = 10 V Vo = 5 V Io = 500 mA 4.4 Vi = 10 V Vo = 5 V Tamb = 25 C CL = 0 F 4.2 Io = 20 mA 1 4.0 10-1 Io = 500 mA 3.8 L7805 10-2 10 102 3.6 -75 f (Hz) 105 104 103 -50 -25 25 0 50 75 100 125 Figure 35. Load transient response Figure 36. Line transient response Vo (V) Vi (V) Vo (mV) Vi = 10 V Vo = 5 V INPUT VOLTAGE L7805 L7805 15 LOAD CURRENT 1 AUTPUT VOLTAGE DEVIATION 0 Tj (C) GAMG200920161321MT GAMG200920161320MT 20 10 10 5 OUTPUT VOLTAGE DEVIATION 0 0 -10 -1 IO = 500 mA Vo = 5 V 0 10 20 30 -20 40 50 T (s) 0 4 2 GAMG200920161326MT 6 8 10 T (s) GAMG200920161328MT Figure 37. Quiescent current vs. input voltage Id(mA) 5.0 VO = 5 V Io = 20 mA Tj = 25 C 4.0 L7805 3.0 5 10 15 20 25 30 Vi (V) GAMG200920161329MT DS0422 - Rev 36 page 31/55 L78 Package information 8 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. DS0422 - Rev 36 page 32/55 L78 TO-220 (dual gauge) package information 8.1 TO-220 (dual gauge) package information Figure 38. TO-220 (dual gauge) package outline 0015988_21_Type A DS0422 - Rev 36 page 33/55 L78 TO-220 (dual gauge) package information Table 19. TO-220 (dual gauge) mechanical data Dim. mm Min. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 DS0422 - Rev 36 Typ. 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 P 3.75 3.85 Q 2.65 2.95 page 34/55 L78 TO-220 (single gauge) package information 8.2 TO-220 (single gauge) package information Figure 39. TO-220 (single gauge) package outline 8174627_5 DS0422 - Rev 36 page 35/55 L78 TO-220 (single gauge) package information Table 20. TO-220 (single gauge) mechanical data Dim. DS0422 - Rev 36 mm Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 E 10.00 10.40 e 2.40 2.70 e1 4.95 5.15 F 0.51 0.60 H1 6.20 6.60 J1 2.40 2.72 L 13.00 14.00 L1 3.50 3.93 L20 16.40 L30 28.90 P 3.75 3.85 Q 2.65 2.95 page 36/55 L78 TO-220FP type A package information 8.3 TO-220FP type A package information Figure 40. TO-220FP package outline 7012510_type_A DS0422 - Rev 36 page 37/55 L78 TO-220 (single/dual) packing information Table 21. TO-220FP package mechanical data Dim. mm Min. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 8.4 Typ. 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 TO-220 (single/dual) packing information Figure 41. Tube for TO-220 (dual gauge) (mm.) DS0422 - Rev 36 page 38/55 L78 DPAK package information Figure 42. Tube for TO-220 (single gauge) (mm.) 8.5 DPAK package information Figure 43. DPAK package outline 0068772_A_21 DS0422 - Rev 36 page 39/55 L78 DPAK package information Table 22. DPAK mechanical data Dim. mm Min. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 R V2 DS0422 - Rev 36 Typ. 1.00 0.20 0 8 page 40/55 L78 DPAK package information Figure 44. DPAK recommended footprint (dimensions are in mm) Footprint_0068772 DS0422 - Rev 36 page 41/55 L78 DPAK (SMD 2L STD-ST) type A package information 8.6 DPAK (SMD 2L STD-ST) type A package information Figure 45. DPAK (SMD 2L STD-ST) type A package outline 0079457_22_type A DS0422 - Rev 36 page 42/55 L78 DPAK (SMD 2L STD-ST) type A package information Table 23. DPAK (SMD 2L STD-ST) mechanical data Dim. mm Min. Max. A 4.40 4.60 A1 0.03 0.23 b 0.70 0.93 b2 1.14 1.70 c 0.45 0.60 c2 1.23 1.36 D 8.95 9.35 D1 7.50 7.75 8.00 D2 1.10 1.30 1.50 E 10 E1 8.50 8.70 8.90 E2 6.85 7.05 7.25 e 10.40 2.54 e1 4.88 5.28 H 15 15.85 J1 2.49 2.69 L 2.29 2.79 L1 1.27 1.40 L2 1.30 1.75 R V2 DS0422 - Rev 36 Typ. 0.4 0 8 page 43/55 L78 DPAK (ASE) type B package information 8.7 DPAK (ASE) type B package information Figure 46. DPAK (ASE subcon) type B package outline 0079457_23_type B DS0422 - Rev 36 page 44/55 L78 DPAK (ASE) type B package information Table 24. DPAK (ASE) type B mechanical data Dim. mm Min. Max. A 4.36 4.56 A1 0 0.25 b 0.70 0.90 b1 0.51 0.89 b2 1.17 1.37 b3 1.36 1.46 c 0.38 0.694 c1 0.38 0.534 c2 1.19 1.34 D 8.60 9.00 D1 6.90 7.50 E 10.15 10.55 E1 8.10 8.70 e 2.54 H 15.00 15.60 L 1.90 2.50 L1 1.65 L2 1.78 L3 L4 DS0422 - Rev 36 Typ. 0.25 4.78 5.28 page 45/55 L78 DPAK (ASE) type B package information Figure 47. DPAK recommended footprint (dimensions are in mm) Footprint_0079457 DS0422 - Rev 36 page 46/55 L78 DPAK and DPAK packing information 8.8 DPAK and DPAK packing information Figure 48. Tape outline DS0422 - Rev 36 page 47/55 L78 DPAK and DPAK packing information Figure 49. Reel outline T 40mm min. access hole at slot location B D C N A G measured at hub Tape slot in core for tape start 2.5mm min.width Full radius AM06038v1 Table 25. DPAK tape and reel mechanical data Tape Dim. DS0422 - Rev 36 Reel mm mm Dim. Min. Max. Min. A0 10.5 10.7 A B0 15.7 15.9 B 1.5 D 1.5 1.6 C 12.8 D1 1.59 1.61 D 20.2 E 1.65 1.85 G 24.4 F 11.4 11.6 N 100 K0 4.8 5.0 T Max. 330 13.2 26.4 30.4 P0 3.9 4.1 P1 11.9 12.1 Base quantity 1000 P2 1.9 2.1 Bulk quantity 1000 R 50 T 0.25 0.35 W 23.7 24.3 page 48/55 L78 DPAK and DPAK packing information Table 26. DPAK tape and reel mechanical data Tape Dim. mm mm Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 DS0422 - Rev 36 Reel Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 18.4 22.4 page 49/55 L78 Ordering information 9 Ordering information Table 27. Order codes Order codes Part number L7805C TO-220 TO-220 (single gauge) (dual gauge) L7805CV L7805CV-DG DPAK DPAK TO-220FP Output voltages L7805CDT-TR L7805CD2T-TR L7805CP 5V L7805AB L7805ABV L7805ABV-DG L7805ABD2T-TR L7805ABP 5V L7805AC L7805ACV L7805ACV-DG L7805ACD2T-TR L7805ACP 5V L7806C L7806CV L7806CV-DG L7806CD2T-TR 6V L7806AB L7806ABV L7806ABV-DG L7806ABD2T-TR 6V L7806AC L7806ACV L7806ACV-DG L7808C L7808CV L7808CV-DG L7808CD2T-TR 8V L7808AB L7808ABV L7808ABV-DG L7808ABD2T-TR 8V L7808AC L7808ACV L7808ACV-DG L7885C L7885CV L7809C L7809CV L7809CV-DG L7809CD2T-TR L7809AB L7809ABV L7809ABV-DG L7809ABD2T-TR L7809AC L7809ACV L7812C L7812CV L7812CV-DG L7812CD2T-TR L7812AB L7812ABV L7812ABV-DG L7812ABD2T-TR 12 V L7812AC L7812ACV L7812ACV-DG L7812ACD2T-TR 12 V L7815C L7815CV L7815CV-DG L7815CD2T-TR L7815AB L7815ABV L7815ABV-DG L7815ABD2T-TR 15 V L7815AC L7815ACV L7815ACV-DG L7815ACD2T-TR 15 V L7818C L7818CV L7818CV-DG L7824C L7824CV L7824CV-DG L7824AB L7824ABV L7824ABV-DG 24 V L7824AC L7824ACV L7824ACV-DG 24 V DS0422 - Rev 36 6V 8V 8.5 V L7809CP 9V 9V 9V L7812CP L7815CP 12 V 15 V 18 V L7824CD2T-TR L7824CP 24 V page 50/55 L78 Revision history Table 28. Document revision history Date Revision Changes 21-Jun-2004 12 Document updating. 03-Aug-2006 13 Order codes has been updated and new template. 19-Jan-2007 14 DPAK mechanical data has been updated and add footprint data. 31-May-2007 15 Order codes has been updated. 29-Aug-2007 16 Added Table 1 in cover page. 11-Dec-2007 17 Modified: Table 27. 06-Feb-2008 18 Added: TO-220 mechanical data Figure 38 on page 38 , Figure 39 on page 39, and Table 23 on page 37. Modified: Table 27 on page 58. 18-Mar-2008 19 Added: Table 29: DPAK mechanical data on page 50, Table 30: Tape and reel DPAK mechanical data on page 52. Modified: Table 27 on page 58. 26-Jan-2010 20 Modified Table 1 on page 1 and Table 23 on page 37, added: Figure 38 on page 38 and Figure 39 on page 39, Figure 40 on page 45 and Figure 41 on page 45. 04-Mar-2010 21 Added notes Figure 38 on page 38. 08-Sep-2010 22 Modified Table 27 on page 58. 23-Nov-2010 23 Added: TJ = 25 C test condition in DVO on Table 3, 4, 5, 6, 7, 8 and Table 9. 16-Sep-2011 24 Modified title on page 1. 30-Nov-2011 25 Added: order codes L7805CV-DG, L7806CV-DG, L7808ABV-DG, L7812CV-DG and L7815CV-DG Table 27 on page 58. 08-Feb-2012 26 Added: order codes L7805ACV-DG, L7805ABV-DG, L7806ABV-DG, L7808CV-DG, L7809CV-DG, L7812ACV-DG, L7818CV-DG, L7824CV-DG Table 27 on page 58. 27-Mar-2012 27 Added: order codes L7812ABV-DG, L7815ABV-DG Table 27 on page 58. 27-Apr-2012 28 Modified: VI = 10.4 to 23 V ==> VI = 11.4 to 23 V test conditon value Line regulation Table 6 on page 13. 10-May-2012 29 Added: order codes L7806ACV-DG, L7808ACV-DG, L7815ACV-DG, L7824ABV-DG and L7824ACV-DG Table 27 on page 58. 19-Sep-2012 30 Modified load regulation units from V to mV in Table 3 to Table 9. 12-Mar-2013 31 Modified: VO output voltage at 25 C min. value 14.4 V Table 16 on page 23. Part numbers L78xx, L78xxC, L78xxAB, L78xxAC changed to L78. Removed TO-3 package. 04-Mar-2014 32 Updated the description in cover page, Section 2: Pin configuration, Section 3: Maximum ratings, Section 4: Test circuits, Section 5: Electrical characteristics, Section 6: Application information, Section 8: Package information and Table 27: Order codes. Added Section 9: Packaging mechanical data. Minor text changes. Updated Section 8: Package information. 26-Feb-2016 33 28-Nov-2016 34 25-May-2018 35 Updated DPAK package Section 8.7 DPAK (ASE) type B package information. 17-Sep-2018 36 Updated Figure 29. Dropout voltage vs junction temperature. DS0422 - Rev 36 Minor text changes. Updated Section 9: "Ordering information". Minor text changes. page 51/55 L78 Contents Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 4 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 5 Electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 6.1 Design consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7 Typical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 8 Package information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 9 8.1 TO-220 (dual gauge) package information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8.2 TO-220 (single gauge) package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8.3 TO-220FP package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 8.4 TO-220 packing information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.5 DPAK package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 8.6 DPAK (SMD 2L STD-ST) type A package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.7 DPAK (ASE subcon) type B package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8.8 DPAK and DPAK packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 DS0422 - Rev 36 page 52/55 L78 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Absolute maximum ratings . . . . . . . . . . . . Thermal data. . . . . . . . . . . . . . . . . . . . . . Electrical characteristics of L7805A . . . . . . Electrical characteristics of L7806A . . . . . . Electrical characteristics of L7808A . . . . . . Electrical characteristics of L7809A . . . . . . Electrical characteristics of L7812A . . . . . . Electrical characteristics of L7815A . . . . . . Electrical characteristics of L7824A . . . . . . Electrical characteristics of L7805C . . . . . . Electrical characteristics of L7806C . . . . . . Electrical characteristics of L7808C . . . . . . Electrical characteristics of L7885C . . . . . . Electrical characteristics of L7809C . . . . . . Electrical characteristics of L7812C . . . . . . Electrical characteristics of L7815C . . . . . . Electrical characteristics of L7818C . . . . . . Electrical characteristics of L7824C . . . . . . TO-220 (dual gauge) mechanical data . . . . TO-220 (single gauge) mechanical data . . . TO-220FP package mechanical data . . . . . DPAK mechanical data . . . . . . . . . . . . . . . DPAK (SMD 2L STD-ST) mechanical data . DPAK (ASE) type B mechanical data. . . . . DPAK tape and reel mechanical data. . . . . DPAK tape and reel mechanical data . . . . . Order codes . . . . . . . . . . . . . . . . . . . . . . Document revision history . . . . . . . . . . . . . DS0422 - Rev 36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . 4 . 6 . 7 . 8 . 9 10 11 12 13 14 15 16 17 18 19 20 21 34 36 38 40 43 45 48 49 50 51 page 53/55 L78 List of figures List of figures Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42. Figure 43. Figure 44. Figure 45. Figure 46. Figure 47. Figure 48. Figure 49. DS0422 - Rev 36 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC parameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load regulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ripple rejection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixed output regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Circuit for increasing output voltage. . . . . . . . . . . . . . . . . . . . . Adjustable output regulator (7 to 30 V) . . . . . . . . . . . . . . . . . . . 0.5 to 10 V regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High current voltage regulator. . . . . . . . . . . . . . . . . . . . . . . . . High output current with short circuit protection . . . . . . . . . . . . . Tracking voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . Split power supply ( 15 V - 1 A) . . . . . . . . . . . . . . . . . . . . . . . Negative output voltage circuit . . . . . . . . . . . . . . . . . . . . . . . . Switching regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High input voltage circuit (configuration 1) . . . . . . . . . . . . . . . . High input voltage circuit (configuration 2) . . . . . . . . . . . . . . . . High input and output voltage . . . . . . . . . . . . . . . . . . . . . . . . . Reducing power dissipation with dropping resistor. . . . . . . . . . . Remote shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power AM modulator (unity voltage gain, IO 0.5). . . . . . . . . . . Adjustable output voltage with temperature compensation . . . . . Light controllers (VO(min) = VXX + VBE) . . . . . . . . . . . . . . . . . . . Protection against input short-circuit with high capacitance loads Dropout voltage vs junction temperature . . . . . . . . . . . . . . . . . Peak output current vs input/output differential voltage. . . . . . . . Supply voltage rejection vs frequency . . . . . . . . . . . . . . . . . . . Output voltage vs junction temperature . . . . . . . . . . . . . . . . . . Output impedance vs frequency . . . . . . . . . . . . . . . . . . . . . . . Quiescent current vs junction temp.. . . . . . . . . . . . . . . . . . . . . Load transient response . . . . . . . . . . . . . . . . . . . . . . . . . . . . Line transient response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quiescent current vs. input voltage . . . . . . . . . . . . . . . . . . . . . TO-220 (dual gauge) package outline . . . . . . . . . . . . . . . . . . . TO-220 (single gauge) package outline . . . . . . . . . . . . . . . . . . TO-220FP package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . Tube for TO-220 (dual gauge) (mm.) . . . . . . . . . . . . . . . . . . . . Tube for TO-220 (single gauge) (mm.) . . . . . . . . . . . . . . . . . . . DPAK package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DPAK recommended footprint (dimensions are in mm). . . . . . . . DPAK (SMD 2L STD-ST) type A package outline . . . . . . . . . . . DPAK (ASE subcon) type B package outline . . . . . . . . . . . . . . DPAK recommended footprint (dimensions are in mm) . . . . . . . Tape outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reel outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . 3 . 3 . 4 . 5 . 5 . 5 22 23 23 23 24 24 24 25 25 26 26 26 27 27 27 28 28 28 29 29 30 30 30 30 31 31 31 31 31 33 35 37 38 39 39 41 42 44 46 47 48 page 54/55 L78 IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2018 STMicroelectronics - All rights reserved DS0422 - Rev 36 page 55/55