Glass passivated junction
Low incremental surge resistance
600W peak pulse power capability with a 10/1000us waveform, repetition
rate (duty cycle): 0.01%
Fast response time
High temperature soldering guaranteed:250°C/10seconds at terminals
Mechanical Data
Case: JEDEC DO-214AA(SMB) molded plastic over passivated junction
Terminals: Solder plated, solderable per MIL-STD-750 Method 2026
Polarity: For unidirectional types the band denotes the cathode,which is positive with respect to
the anode under normal TVS
Notes:
1. Non-repetitive current pulse, per Fig.3 and derated above TA=25°C per Fig.2
2. Mounted on 0.2 x 0.2" (5.0 x 5.0 mm) copper pads to each terminal
3. Mounted on minimum recommended pad layout
DO-214AA(SMB)
Absolute Maximum Ratings (TA=25°C unless otherwise specified)
Features
■
■
1/5
■
■
■
Weight: 0.003oz., 0.093g
P6SMBx Series
Surface Mount Transient Voltage Suppressors Peak
Pulse Power 600W Breakdown Voltage 6.8V to 550V
Symbol Unit
PPPM W
IPPM A
PM(AV) W
IFSM A
RθJA °C/W
RθJL °C/W
TJ°C
TSTG °C
Operating Junction Temperature Range
Storage Temperature Range
Value
Minimum 600
See Next Table
100
100
20
-55 to +150
-55 to +150
Peak Forward Surge Current 8.3ms Single Half Sine-wave
Uni-Directional Only2
Typical Thermal Resistance, Junction To Ambient Air3
Typical Thermal Resistance, Junction To Leads
Power Dissipation On Infinite Heatsink, TA=50°C 5
Parameter
Peak Pulse Current With a 10/1000us Waveform1
Peak Pulse Power Dissipation With a 10/1000us Waveform1,2
2/5
Electrical Characteristics TA=25°C unless otherwise specified,VF=3.5V at IF=50A (uni-directional only)
P6SMBx Series
Part Number
(Uni) Part Number
(Bi)
Marking Code
Breakdown
Voltage1
Test
Current
Stand-
off
Voltage
Max.
Reverse
Leakage
Current3
Max.
Clamping
Voltage
Max.
Peak
Pulse
Current2
Max.
Temperature
Coefficient
Of
VBR
V(BR)1
IT VWM
ID
@VWM
VC
@ I PPM IPPM
UNI BI Min. Max.
V V mA V μA V A (% / °C)
P6SMB6.8A P6SMB6.8CA 6V8A 6V8C 6.45 7.14 10 5.80 1000 10.5 57.1 0.05
P6SMB7.5A P6SMB7.5CA 7V5A 7V5C 7.13 7.88 10 6.40 500 11.3 53.1 0.061
P6SMB8.2A P6SMB8.2CA 8V2A 8V2C 7.79 8.61 10 7.02 200 12.1 49.6 0.065
P6SMB9.1A P6SMB9.1CA 9V1A 9V1C 8.65 9.55 1.0 7.78 50 13.4 44.8 0.068
P6SMB10A P6SMB10CA 10A 10C 9.50 10.5 1.0 8.55 10 14.5 41.4 0.073
P6SMB11A P6SMB11CA 11A 11C 10.5 11.6 1.0 9.40 5.0 15.6 38.5 0.075
P6SMB12A P6SMB12CA 12A 12C 11.4 12.6 1.0 10.2 5.0 16.7 35.9 0.078
P6SMB13A P6SMB13CA 13A 13C 12.4 13.7 1.0 11.1 5.0 18.2 33.0 0.081
P6SMB15A P6SMB15CA 15A 15C 14.3 15.8 1.0 12.8 1.0 21.2 28.3 0.084
P6SMB16A P6SMB16CA 16A 16C 15.2 16.8 1.0 13.6 1.0 22.5 26.7 0.086
P6SMB18A P6SMB18CA 18A 18C 17.1 18.9 1.0 15.3 1.0 25.2 23.8 0.088
P6SMB20A P6SMB20CA 20A 20C 19.0 21.0 1.0 17.1 1.0 27.7 21.7 0.090
P6SMB22A P6SMB22CA 22A 22C 20.9 23.1 1.0 18.8 1.0 30.6 19.6 0.092
P6SMB24A P6SMB24CA 24A 24C 22.8 25.2 1.0 20.5 1.0 33.2 18.1 0.094
P6SMB27A P6SMB27CA 27A 27C 25.7 28.4 1.0 23.1 1.0 37.5 16.0 0.096
P6SMB30A P6SMB30CA 30A 30C 28.5 31.5 1.0 25.6 1.0 41.4 14.5 0.097
P6SMB33A P6SMB33CA 33A 33C 31.4 34.7 1.0 28.2 1.0 45.7 13.1 0.098
P6SMB36A P6SMB36CA 36A 36C 34.2 37.8 1.0 30.8 1.0 49.9 12.0 0.099
P6SMB39A P6SMB39CA 39A 39C 37.1 41.0 1.0 33.3 1.0 53.9 11.1 0.100
P6SMB43A P6SMB43CA 43A 43C 40.9 45.2 1.0 36.8 1.0 59.3 10.1 0.101
P6SMB47A P6SMB47CA 47A 47C 44.7 49.4 1.0 40.2 1.0 64.8 9.3 0.101
P6SMB51A P6SMB51CA 51A 51C 48.5 53.6 1.0 43.6 1.0 70.1 8.6 0.102
P6SMB56A P6SMB56CA 56A 56C 53.2 58.8 1.0 47.8 1.0 77.0 7.8 0.103
P6SMB62A P6SMB62CA 62A 62C 58.9 65.1 1.0 53.0 1.0 85.0 7.1 0.104
P6SMB68A P6SMB68CA 68A 68C 64.6 71.4 1.0 58.1 1.0 92.0 6.5 0.104
P6SMB75A P6SMB75CA 75A 75C 71.3 78.8 1.0 64.1 1.0 103 5.8 0.105
P4SMA82A P4SMA82CA 82A 82C 77.9 86.1 1.0 70.1 1.0 113 5.3 0.105
Surface Mount Transient Voltage Suppressors Peak
Pulse Power 600W Breakdown Voltage 6.8V to 550V
Electrical Characteristics TA=25°C unless otherwise specified,VF=3.5V at IF=50A (uni-directional only)
3/5
Notes: 1. V(BR) measured after IT applied for 300us square wave pulse or equivalent
2. Surge current waveform per Fig. 3 and derate per Fig. 2
3. For bi-directional types having VWM of 10 Volts and less, the ID limit is doubled
4. All terms and symbols are consistent with ANSI/IEEE C62.35
P6SMBx Series
Part Number
(Uni) Part Number
(Bi)
Marking Code
Breakdown
Voltage1 Test
Current
Stand-
off
Voltage
Max.
Reverse
Leakage
Current3
Max.
Clamping
Voltage
Max.
Peak
Pulse
Current2
Max.
Temperature
Coefficient
Of
VBR
V(BR)1
IT VWM
ID
@VWM
VC
@ I PPM IPPM
UNI BI Min. Max.
V V mA V μA V A (% / °C)
P6SMB91A P6SMB91CA 91A 91C 86.5 95.5 1.0 77.8 1.0 125 4.8 0.106
P6SMB100A P6SMB100CA 100A 100C 95.0 105 1.0 85.5 1.0 137 4.4 0.106
P6SMB110A P6SMB110CA 110A 110C 105 116 1.0 94.0 1.0 152 3.9 0.107
P6SMB120A P6SMB120CA 120A 120C 114 126 1.0 102 1.0 165 3.6 0.107
P6SMB130A P6SMB130CA 130A 130C 124 137 1.0 111 1.0 179 3.4 0.107
P6SMB150A P6SMB150CA 150A 150C 143 158 1.0 128 1.0 207 2.9 0.108
P6SMB160A P6SMB160CA 160A 160C 152 168 1.0 136 1.0 219 2.7 0.108
P6SMB170A P6SMB170CA 170A 170C 162 179 1.0 145 1.0 234 2.6 0.108
P6SMB180A P6SMB180CA 180A 180C 171 189 1.0 154 1.0 246 2.4 0.108
P6SMB200A P6SMB200CA 200A 200C 190 210 1.0 171 1.0 274 2.2 0.108
P6SMB220A P6SMB220CA 220A 220C 209 231 1.0 185 1.0 328 1.9 0.108
P6SMB250A P6SMB250CA 250A 250C 237 263 1.0 214 1.0 344 1.8 0.108
P6SMB300A P6SMB300CA 300A 300C 285 315 1.0 256 1.0 414 1.5 0.108
P6SMB350A P6SMB350CA 350A 350C 332 368 1.0 300 1.0 482 1.3 0.108
P6SMB400A P6SMB400CA 400A 400C 380 420 1.0 342 1.0 548 1.1 0.108
P6SMB440A P6SMB440CA 440A 440C 418 462 1.0 376 1.0 602 1.0 0.108
P6SMB480A P6SMB480CA 480A 480C 456 504 1.0 408 1.0 658 0.9 0.108
P6SMB510A P6SMB510CA 510A 510C 485 535 1.0 434 1.0 698 0.9 0.108
P6SMB530A P6SMB530CA 530A 530C 503.5 556.5 1.0 477 1.0 725 0.8 0.108
P6SMB540A P6SMB540CA 540A 540C 513 567 1.0 459 1.0 740 0.8 0.108
P6SMB550A P6SMB550CA 550A 550C 522.5 577.5 1.0 495 1.0 760 0.8 0.108
Surface Mount Transient Voltage Suppressors Peak
Pulse Power 600W Breakdown Voltage 6.8V to 550V
Ratings and Characteristic Curves (TA = 25 °C unless otherwise noted)
Figure 1. Peak Pulse Power Rating Curve Figure 2. Pulse Derating Curve
Figure 3. Pulse Waveform Figure 4. Typical Junction Capacitance
Figure 6. Maximum Non-Repetitive Peak Forward Surge
Current
Figure 5. Typical Transient Thermal Impedance
4/5
P6SMBx Series
Surface Mount Transient Voltage Suppressors Peak
Pulse Power 600W Breakdown Voltage 6.8V to 550V
0.2x0.2" (5.0x5.0mm)
Copper Pad Areas
DO-214AA(SMB)
www.goodarksemi.com Doc.USP6SMBxSD2.0
Jan. 2020
Package Outline Dimensions
5/5
Recommended Pad Layout
on uni-directional only
Min. Max. Min. Max.
A1.99 2.61 0.078 0.103
A1 0.00 0.20 0.000 0.008
B1.93 2.08 0.076 0.082
C0.15 0.31 0.006 0.012
D3.48 3.73 0.137 0.147
E4.25 4.75 0.167 0.187
HE 5.26 5.46 0.207 0.215
L0.90 1.41 0.035 0.056
SMB (DO-214AA)
DIM Millimeters Inches
Min. Max. Min. Max.
J - 2.60 -0.102
K2.20 -0.087 -
M1.80 -0.071 -
DIM Millimeters Inches
SMB Recommended Pad Layout (Reference Only)
P6SMBx Series
Surface Mount Transient Voltage Suppressors Peak
Pulse Power 600W Breakdown Voltage 6.8V to 550V
