November 2009 Doc ID 11423 Rev 6 1/20
20
STGB10NC60KD, STGD10NC60KD
STGF10NC60KD, STGP10NC60KD
10 A, 600 V short-circuit rugged IGBT
Features
Lower on voltage drop (VCE(sat))
Lower CRES / CIES ratio (no cross-conduction
susceptibility)
Very soft ultra fast recovery antiparallel diode
Short-circuit withstand time 10µs
Description
This IGBT utilizes the advanced PowerMESH™
process resulting in an excellent trade-off
between switching performance and low on-state
behavior.
Applications
High frequency motor controls
SMPS and PFC in both hard switch and
resonant topologies
Motor drives
Figure 1. Internal schematic diagram
TO-220FP TO-220
D2PAK DPAK
123
12
3
1
3
1
3
TAB TAB
TAB
Table 1. Device summary
Order codes Marking Packages Packaging
STGB10NC60KDT4 GB10NC60KD D2PA K Tape and reel
STGD10NC60KDT4 GD10NC60KD DPAK
STGF10NC60KD GF10NC60KD TO-220FP Tu b e
STGP10NC60KD GP10NC60KD TO-220
www.st.com
Contents STGx10NC60KD
2/20 Doc ID 11423 Rev 6
Contents
1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
STGx10NC60KD Electrical ratings
Doc ID 11423 Rev 6 3/20
1 Electrical ratings
Table 2. Absolute maximum ratings
Symbol Parameter
Value
Unit
D²PAK
TO-220 DPAK TO-220FP
VCES Collector-emitter voltage (VGE = 0) 600 V
IC(1) Continuous collector current at TC = 25°C 20 9 A
IC(1) Continuous collector current at TC = 100°C 10 6 A
ICL(2) Turn-off latching current 30 A
ICP(3) Pulsed collector current 30 A
VGE Gate-emitter voltage ±20 V
IFDiode RMS forward current at Tc=25°C 10 A
IFSM
Surge non repetitive forward current Tp = 10 ms
sinusoidal 20 A
PTOT Total dissipation at TC = 25°C 65 62 25 W
VISO
Insulation withstand voltage (RMS) from all three
leads to external heat sink (t=1s;TC=25°C) -- 2500 V
tscw
Short-circuit withstand time
VCE = 0.5 VCES, Tj = 125 °C, RG = 10 , VGE = 12 V 10 µs
Tstg Storage temperature
– 55 to 150 °C
TjOperating junction temperature
1. Calculated according to the iterative formula
2. Vclamp = 80 % VCES, VGE = 15 V, RG = 10 , TJ = 150 °C
3. Pulse width limited by maximum junction temperature and turn-off within RBSOA
ICTC
() Tjmax()
TC
Rthj cVCE sat()max()
Tjmax()
ICTC
(),()×
----------------------------------------------------------------------------------------------------------=
Electrical ratings STGx10NC60KD
4/20 Doc ID 11423 Rev 6
Table 3. Thermal data
Symbol Parameter
Value
Unit
TO-220
D²PAK DPAK TO-220FP
Rthj-case Thermal resistance junction-case IGBT 1.9 2 5
°C/W
Rthj-case Thermal resistance junction-case diode 4 4.5 7
Rthj-amb Thermal resistance junction-ambient 62.5 100 62.5
STGx10NC60KD Electrical characteristics
Doc ID 11423 Rev 6 5/20
2 Electrical characteristics
(Tj =25°C unless otherwise specified)
Table 4. Static
Symbol Parameter Test conditions Min. Typ. Max. Unit
V(BR)CES
Collector-emitter
breakdown voltage
(VGE= 0)
IC= 1mA 600 V
VCE(sat) Collector-emitter saturation
voltage
VGE= 15V, IC= 5A
VGE= 15V, IC= 5A, Tj= 125°C
2.2
1.8
2.5 V
V
VGE(th) Gate threshold voltage VCE= VGE, IC= 250µA 4.5 6.5 V
ICES
Collector cut-off current
(VGE = 0)
VCE= 600 V
VCE=600 V, Tj = 125°C
150
1
µA
mA
IGES
Gate-emitter leakage
current (VCE = 0) VGE= ±20V ±100 nA
gfs(1)
1. Pulse test: pulse duration < 300 µs, duty cycle < 2 %
Forward transconductance VCE = 15V, IC= 5A 15 S
Table 5. Dynamic
Symbol Parameter Test conditions Min. Typ. Max. Unit
Cies
Coes
Cres
Input capacitance
Output capacitance
Reverse transfer
capacitance
VCE = 25V, f = 1MHz,
VGE = 0 -
380
46
8.5
-
pF
pF
pF
Qg
Qge
Qgc
Total gate charge
Gate-emitter charge
Gate-collector charge
VCE = 390V, IC = 5A,
VGE = 15V,
(see Figure 19)
-
19
5
9
-
nC
nC
nC
Electrical characteristics STGx10NC60KD
6/20 Doc ID 11423 Rev 6
Table 6. Switching on/off (inductive load)
Symbol Parameter Test conditions Min. Typ. Max. Unit
td(on)
tr
(di/dt)on
Turn-on delay time
Current rise time
Turn-on current slope
VCC = 390V, IC = 5A
RG= 10, VGE= 15V
(see Figure 20)
-
17
6
655
-
ns
ns
A/µs
td(on)
tr
(di/dt)on
Turn-on delay time
Current rise time
Turn-on current slope
VCC = 390V, IC = 5A
RG= 10, VGE= 15V,
Tj=125°C
(see Figure 20)
-
16.5
6.5
575
-
ns
ns
A/µs
tr(Voff)
td(off)
tf
Off voltage rise time
Turn-off delay time
Current fall time
Vcc = 390V, IC = 5A,
RGE = 10, VGE = 15V
(see Figure 20)
-
33
72
82
-
ns
ns
ns
tr(Voff)
td(off)
tf
Off voltage rise time
Turn-off delay time
Current fall time
Vcc = 390V, IC = 5A,
RGE=10, VGE =15V,
Tj=125°C
(see Figure 20)
-
60
106
136
-
ns
ns
ns
Table 7. Switching energy (inductive load)
Symbol Parameter Test conditions Min. Typ. Max. Unit
Eon(1)
Eoff(2)
Ets
1. Eon is the tun-on losses when a typical diode is used in the test circuit in figure 2. If the IGBT is offered in
a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the
same temperature (25°C and 125°C)
2. Turn-off losses include also the tail of the collector current
Turn-on switching losses
Turn-off switching losses
Total switching losses
VCC = 390V, IC = 5A
RG=10, VGE=15V
(see Figure 20)
-
55
85
140
-
µJ
µJ
µJ
Eon(1)
Eoff(2)
Ets
Turn-on switching losses
Turn-off switching losses
Total switching losses
VCC = 390V, IC = 5A
RG=10, VGE= 15V,
Tj= 125°C
(see Figure 20)
-
87
162
249
-
µJ
µJ
µJ
STGx10NC60KD Electrical characteristics
Doc ID 11423 Rev 6 7/20
Table 8. Collector-emitter diode
Symbol Parameter Test conditions Min Typ. Max. Unit
VFForward on-voltage IF=5 A
IF=5 A, Tj=125 °C -2
1.6 -V
V
trr
Qrr
Irrm
Reverse recovery time
Reverse recovery charge
Reverse recovery current
IF=5 A, VR=40 V,
di/dt=100 A/µs
(see Figure 5)
-
22
14
1.3
-
ns
nC
A
trr
Qrr
Irrm
Reverse recovery time
Reverse recovery charge
Reverse recovery current
IF=5 A, VR=40 V,
Tj=125 °C, di/dt=100 A/µs
(see Figure 5)
-
35
40
2.2
-
ns
nC
A
Electrical characteristics STGx10NC60KD
8/20 Doc ID 11423 Rev 6
2.1 Electrical characteristics (curves)
Figure 2. Output characteristics Figure 3. Transfer characteristics
Figure 4. Transconductance Figure 5. Collector-emitter on voltage vs
temperature
Figure 6. Gate charge vs gate-source voltage Figure 7. Capacitance variations
STGx10NC60KD Electrical characteristics
Doc ID 11423 Rev 6 9/20
Figure 8. Normalized gate threshold voltage
vs temperature
Figure 9. Collector-emitter on voltage vs
collector current
Figure 10. Normalized breakdown voltage vs
temperature
Figure 11. Switching losses vs temperature
Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector
current
Electrical characteristics STGx10NC60KD
10/20 Doc ID 11423 Rev 6
Figure 14. Thermal impedance for D²PAK,
DPAK and TO-220
Figure 15. Turn-off SOA
Figure 16. Emitter-collector diode
characteristics
Figure 17. Thermal impedance for TO-220FP







) !
&-
6 6
&-
4 #
MAXIMUMVALUES
J
4 #
MAXIMUMVALUES
J
4 #
TYPICALVALUES
J
STGx10NC60KD Test circuits
Doc ID 11423 Rev 6 11/20
3 Test circuits
Figure 18. Test circuit for inductive load
switching
Figure 19. Gate charge test circuit
Figure 20. Switching waveform Figure 21. Diode recovery time waveform
Package mechanical data STGx10NC60KD
12/20 Doc ID 11423 Rev 6
4 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
STGx10NC60KD Package mechanical data
Doc ID 11423 Rev 6 13/20
Figure 22. D2PAK package drawing
Table 9. D2PAK package mechanical data
Dim.
mm inch
Min. Typ. Max. Min. Typ. Max.
A 4.40 4.60 0.173 0.181
A1 0.03 0.23 0.001 0.009
b 0.70 0.93 0.027 0.037
b2 1.14 1.70 0.045 0.067
c 0.45 0.60 0.017 0.024
c2 1.23 1.36 0.048 0.053
D 8.95 9.35 0.352 0.368
D1 7.50 0.295
E 10 10.40 0.394 0.409
E1 8.50 0.334
e 2.54 0.1
e1 4.88 5.28 0.192 0.208
H 15 15.85 0.590 0.624
J1 2.49 2.69 0.099 0.106
L 2.29 2.79 0.090 0.110
L1 1.27 1.40 0.05 0.055
L2 1.30 1.75 0.051 0.069
R 0.4 0.016
V2
0079457_M
Package mechanical data STGx10NC60KD
14/20 Doc ID 11423 Rev 6
Figure 23. DPAK package drawing
Table 10. DPAK package mechanical data
Dim.
mm
Min. Typ Max.
A 2.20 2.40
A1 0.90 1.10
A2 0.03 0.23
b 0.64 0.90
b4 5.20 5.40
c 0.45 0.60
c2 0.48 0.60
D 6.00 6.20
D1 5.10
E 6.40 6.60
E1 4.70
e2.28
e1 4.40 4.60
H 9.35 10.10
L1
L1 2.80
L2 0.80
L4 0.60 1
R0.20
V2 0 o8 o
0068772_G
STGx10NC60KD Package mechanical data
Doc ID 11423 Rev 6 15/20
Figure 24. TO-220FP package drawing
Table 11. TO-220FP package mechanical data
Dim.
mm
Min. Typ. Max.
A4.4 4.6
B2.5 2.7
D 2.5 2.75
E0.45 0.7
F0.75 1
F1 1.15 1.70
F2 1.15 1.70
G4.95 5.2
G1 2.4 2.7
H 10 10.4
L2 16
L3 28.6 30.6
L4 9.8 10.6
L5 2.9 3.6
L6 15.9 16.4
L7 9 9.3
Dia 3 3.2
7012510_Rev_K
A
B
H
Dia
L7
D
E
L6 L5
L2
L3
L4
F1 F2
F
G
G1
Package mechanical data STGx10NC60KD
16/20 Doc ID 11423 Rev 6
Figure 25. TO-220 type A package drawing
Table 12. TO-220 type A mechanical data
Dim.
mm
Min. Typ. Max.
A4.40 4.60
b0.61 0.88
b1 1.14 1.70
c0.48 0.70
D 15.25 15.75
D1 1.27
E 10 10.40
e2.40 2.70
e1 4.95 5.15
F1.23 1.32
H1 6.20 6.60
J1 2.40 2.72
L13 14
L1 3.50 3.93
L20 16.40
L30 28.90
P3.75 3.85
Q2.65 2.95
0015988_S
STGx10NC60KD Packaging mechanical data
Doc ID 11423 Rev 6 17/20
5 Packaging mechanical data
TAPE AND REEL SHIPMENT
D
2
PAK FOOTPRINT
DIM. mm inch
MIN. MAX. MIN. MAX.
A330 12.992
B1.5 0.059
C12.813.2 0.504 0.520
D20.2 0795
G 24.4 26.4 0.960 1.039
N100 3.937
T30.4 1.197
BASE QTY BULK QTY
1000 1000
REEL MECHANICAL DATA
DIM. mm inch
MIN. MAX. MIN. MAX.
A0 10.5 10.7 0.4130.421
B0 15.7 15.9 0.6180.626
D 1.5 1.6 0.059 0.063
D1 1.59 1.61 0.062 0.063
E1.651.85 0.065 0.073
F11.4 11.6 0.449 0.456
K0 4.85.0 0.189 0.197
P0 3.9 4.1 0.1530.161
P1 11.9 12.1 0.4680.476
P2 1.9 2.1 0.075 0.082
R 50 1.574
T0.250.35 0.00980.0137
W 23.7 24.30.933 0.956
TAPE MECHANICAL DATA
Packaging mechanical data STGx10NC60KD
18/20 Doc ID 11423 Rev 6
TAPE AND REEL SHIPMENT
DPAK FOOTPRINT
DIM. mm inch
MIN. MAX. MIN. MAX.
A 330 12.992
B1.5 0.059
C 12.8 13.2 0.504 0.520
D20.2 0.795
G 16.4 18.4 0.645 0.724
N50 1.968
T 22.4 0.881
BASE QTY BULK QTY
2500 2500
REEL MECHANICAL DATA
DIM. mm inch
MIN. MAX. MIN. MAX.
A0 6.8 7 0.267 0.275
B0 10.4 10.6 0.409 0.417
B1 12.1 0.476
D1.5 1.6 0.059 0.063
D1 1.5 0.059
E1.65 1.85 0.065 0.073
F 7.4 7.6 0.291 0.299
K0 2.55 2.75 0.100 0.108
P0 3.9 4.1 0.153 0.161
P1 7.9 8.1 0.311 0.319
P2 1.9 2.1 0.075 0.082
R40 1.574
W 15.7 16.3 0.618 0.641
TAPE MECHANICAL DATA
All dimensions are in millimeters
STGx10NC60KD Revision history
Doc ID 11423 Rev 6 19/20
6 Revision history
Table 13. Document revision history
Date Revision Changes
14-Jun-2005 1 New release.
19-Jul-2005 2 Complete version.
27-Jan-2006 3 Inserted ecopack indication.
01-Mar-2006 4 The document has been reformatted.
08-Feb-2007 5 Modified value on Table 6.: Switching on/off (inductive load).
24-Nov-2009 6 Inserted DPAK package option.
STGx10NC60KD
20/20 Doc ID 11423 Rev 6
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com