cui.com
date 01/17/2013
page 1 of 7
SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
MODEL output
voltage
output
current
output
power
ripple
and noise1
ef ciency
(Vdc)
max
(A)
max
(W)
max
(mVp-p) (%)
VDRS-150-24 24 6.3 150 240 87
VDRS-150-48 48 3.2 150 480 87
Note: 1. at full load, 230 Vac input, measured at 20MHz bandwidth with a 47 μF and 0.1 μF parallel cap on the output
2. 3 seconds or 20% duty cycle max. The average output power should not exceed the rated power.
PART NUMBER KEY
VDRS - 150 - XX
Output
Voltage
Base Number
FEATURES
• up to 150 W continuous power
• universal input (88~264 Vac / 124~373 Vdc)
• 150% peak load capability2
• DIN Rail power supplies
• two peak load mode selector
• built-in remote ON/OFF function
• over voltage, over load, and over temperature protections
• UL 508 and TUV safety approvals
• built-in active PFC function (PF 0.90 at 115 Vac, 0.98 at 230 Vac)
• efficiency up to 87%
For more information, please visit the product page.
cui.com
date 01/17/2013 page 2 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
INPUT
parameter conditions/description min typ max units
voltage 88
124
264
373
Vac
Vdc
frequency 47 63 Hz
current at 115 Vac
at 230 Vac
2.6
1.3
A
A
inrush current at 115 Vac
at 230 Vac
33
65
A
A
power factor correction at 230 Vac
at 115 Vac
0.90
0.98
leakage current at 240 Vac 1mA
OUTPUT
parameter conditions/description min typ max units
voltage accuracy ±1 %
line regulation ±0.5 %
load regulation 1%
temperature coef cient (0 ~ 50°C) ±0.03 %/°C
hold-up time at 115 / 230 Vac, cold start 16 ms
voltage adjustment range -2 +8 %
Note: 1. All speci cation are measured at 230 Vac input, rated load, 25°C unless otherwise speci ed.
PROTECTIONS
parameter conditions/description min typ max units
over voltage protection
latch-off mode, restart
to recover from fault
24 V model
48 V model
120
117
138
135
%
%
Kicks in between 105~150% rated output power
when the fault persist for about 3 sec, then clamps
output voltage down, automatic recovery’ >150%
rated power or short circuit would cause the power
supply to go in to constant current limiting; if fault
condition is not removed after 5 times, then the
converter will shutdown and need to be restarted
to recover from fault.
over load protection constant current limiting, automatically recovers
after fault condition is removed 105 150 %
over temperature protection output shut down and auto restart upon reduction
of temperature 90 95 100 °C
DC ok relay contact ratings at 0.3 A
at 1 A and 0.5 A
60
30
Vdc
Vdc
For more information, please visit the product page.
cui.com
date 01/17/2013 page 3 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
SAFETY & COMPLIANCE
parameter conditions/description min typ max units
isolation voltage
input to output for 1 minute
input to case for 1 minute
output to case, output to DC OK for 1 minute
4,242
2,121
707
Vdc
Vdc
Vdc
isolation resistance input to output, input to case,
output to case, 500 Vdc 100 MΩ
safety approvals UL 508, TUV EN 60950-1
EMI/EMC2EN 55022 (CISPR22) Class B, EN 61000-3-(2, 3), EN 61000-4-(2,3,4,5,6,8,11) ENV 50204, EN 55024,
EN 61000-6-2 (EN50082-2), EN 61204-3, heavy industry level, criteria A, meet SEMI F47
RoHS compliant yes
Note: 2. The power supply is considered a component which will be installed into a nal equipment. The nal equipment must be re-con rmed that it still
meets EMC directives.
ENVIRONMENTAL
parameter conditions/description min typ max units
operating temperature -10 70 °C
storage temperature -40 85 °C
operating humidity non-condensing 20 90 %
storage humidity 10 95 %
vibration (10 ~ 500 Hz, 1 hour per axis, 3 hours total) 2 Grms
For more information, please visit the product page.
cui.com
date 01/17/2013 page 4 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
DC ON
+V
ADJ.
+
SW1
SW2
ON OFF
1
CN1
23
CN2
35
55.5
99.8
125
123456
Relay Contact
MECHANICAL DRAWING
CN1
1FG
2 ac line
3 ac neutral
CN2
1 DC+
2DC-
3 INH+
4 INH-
5 relay contact
6 relay contact
Switch
1 peak load setting
2 remote on/off setting
Admissible DIN-RAIL:
TS35/7.5 or TS35/15
MECHANICAL
parameter conditions/description min typ max units
dimensions 2.185 x 4.921 x 3.929 (55.5 x 125 x 99.8 mm) inch
For more information, please visit the product page.
cui.com
date 01/17/2013 page 5 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
I
T
I-normal
I-peak
T-peak
T-normal
0
I
T
I-peak
T-peak
03 ~ 4 sec
0
2
4
6
8
10
12
14
16
18
20
22
24
10% 20% 30% 40% 50% 60% 70% 80% 90%
T-normal
I-normal
0
2
4
6
8
10
12
14
16
18
20
22
110% 115% 120% 125% 130% 135% 140% 145% 150%
T-peak
I-peak
T-peak presents while the unit is working within 110%~150% raterd output power.
See Curve “B” for the variation in T-Peak between output current and hold-up time.
If T-peak is more than the time setting in Curve “B”, the output current will drop to
the constant limit (I-normal) that is 105% of the rated power. Meanwhile, I-normal
and T-normal will be presenting. See Curve “A” for the timing back to I-Peak of
T-normal and this mode can be used for easy 2-stage battery chargers.
CURVE BCURVE A
T-peak presents while the unit is working within 110%~150% rated output power.
See Curve “B” for the variation of T-peak between output current and hold-up time.
If T-peak is more than the time setting in Curve “B”, the output voltage sill be shut
down for 3~4 seconds and then auto-recover.
PEAK LOADING SW1 ON (MODE1) DEFAULT SETTING
PEAK LOADING SW1 OFF (MODE2)
For more information, please visit the product page.
cui.com
date 01/17/2013 page 6 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
DERATING CURVE
Ambient temperature (°C)
Load (%)
Load (%)
-10 40 50
40
60
100
80
125
150
60
100
80
40
60
20
0
88
Input Voltage (Vac) 60 Hz
264100
Output power vs. Ambient temperature Output power vs. Input Voltage
110 120
010 20 30 70
112.5
for 3 sec. typ.
continuous
50
ACTIVE DC SIGNAL - RELAY CONTACT
Contact Close When the output voltage reaches the adjusted output voltage
Contact Open When the output voltage drops below 45%
Contact Ratings (MAX) 30 V / 1 A resistive load
Note: 1. Derating may be needed under low input voltage. Please check the derating curve for more details.
REMOTE ON/OFF
The power supply can be turned on/off by using the “remote control” function.
123456
Relay Contact
DC ON
+V
ADJ.
+
SW1
SW2
ON OFF
CN2
SW External Power Source
I=6~20mA
SW2 INH+(3 PIN)/INH-(4 PIN) Output Status
off SW ON (>2.5 V) ENABLE
off SW OFF (<0.8 V) DISABLE
on SW ON (>2.5 V) DISABLE
on SW OFF (<0.8 V) ENABLE (default setting)
For more information, please visit the product page.
CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website.
CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is
assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use.
CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
Headquarters
20050 SW 112th Ave.
Tualatin, OR 97062
800.275.4899
Fax 503.612.2383
cui.com
techsupport@cui.com
date 01/17/2013 page 7 of 7CUI Inc SERIES: VDRS-150 DESCRIPTION: AC-DC DIN RAIL
rev. description date
1.0 initial release 10/17/2012
1.01 spec. update 11/07/2012
1.02 spec. update 01/17/2013
The revision history provided is for informational purposes only and is believed to be accurate.
REVISION HISTORY
For more information, please visit the product page.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
CUI Inc.:
VDRS-150-24 VDRS-150-48