LM2468 Monolothic Triple 14nS High Gain CRT Driver General Description The LM2468 is an integrated high voltage CRT driver circuit designed for use in color monitor applications. The IC contains three high input impedance wide band amplifiers, which directly drive the RGB cathodes of a CRT. Each channel has its gain internally set to -20 and can drive CRT capacitive loads as well as resistive loads present in other applications, limited only by the package's power dissipation. The IC is packaged in an industry standard 9 lead TO-220 molded plastic package. n 0V to 3.75V input range n Stable with 0-20pF capacitive loads and inductive peaking networks n Matched to the LM126X series preamplifier and LM2479/2480 bias clamp n Maintains standard LM243X Family Pinout which is designed for easy PCB layout n Convenient TO-220 staggered 9 lead package style Applications n Higher gain to accommodate CMOS preamplifiers n Up to 1024 X 768 at 60 Hz (or 800 X 600 at 72/75 Hz) n Pixel clock frequencies up to 50 MHz n Monitors using video blanking Schematic Diagram Connection Diagram Features DS200135-2 Note: Tab is at GND. DS200135-1 FIGURE 1. Simplified Schematic Diagram (One Channel) (c) 2000 National Semiconductor Corporation DS200135 FIGURE 2. Top View Order Number: LM2468TA NS package Number: TA09A www.national.com LM2468 Monolothic Triple 14nS High Gain CRT Driver December 2000 LM2468 Absolute Maximum Ratings (Notes 1, 3) Limits of Operating Ranges If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC +60V to +85V +8V to 15V VBB 0V to +3.75V VIN +15V to +75V VOUT Case Temperature -20C to +115C Do not operate the part without a heat sink. Supply Voltage, VCC Bias Voltage, VBB Input Voltage, VIN Storage Temperature Range, TSTG Lead Temperature (Soldering, < 10sec.) ESD Tolerance, Human Body Model +90V +16V 0V to 4.5V -65C to +150C 300C 2kV (Note 2) Electrical Characteristics (See Figure 3 for Test Circuit) Unless otherwise noted: VCC = +80V, VBB = +12V, CL = 8pF, TC = 50C. DC Tests: VIN = +2.25VDC AC Tests: Output = 40VPP (25V - 65V) at 1MHz Typ Max Units ICC Symbol Supply Current Spec Parameter Three Channels, No Input Signal, No Output Load Conditions Min 18 25 mA IBB Bias Current All three Channels 14 20 mA VDC VOUT DC Output Voltage No AC Input Signal, VIN = 1.25V 62 65 68 AV DC Voltage Gain No AC Input Signal -18 -20 -22 AV Gain Matching Note 4, No AC Input Signal LE Linearity Error Note 4, 5, No AC Input Signal 5 % tR Rise Time Note 6, 10% to 90% 14 nS tF Fall Time Note 6, 90% to 10% 14 nS OS Overshoot Note 6 1 % 1.0 dB Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 2: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and the test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may change when the device is not operated under the listed test conditions. Note 3: All voltages are measured with respect to GND, unless otherwise specified. Note 4: Calculated value from Voltage Gain test on each channel. Note 5: Linearity Error is the variation in DC Gain from Vin = 1.0 volts to Vin = 3.5 volts. Note 6: Input from signal generator: tR, tF < 1nS. AC Test Circuit DS200135-3 Note 7: 8 pF load includes parasitics and FET probe (if used). Note 8: The heatsink must be grounded. Note 9: Compensation Cap is chosen for good correlation to FET probe. Note 10: Input and output cables should be low loss 50 coax, less than 1M long. FIGURE 3. Test Circuit (One Channel) www.national.com 2 (VCC = +80VDC, VBB = +12VDC, CL = +8pF, VOUT = 40VPP (25- 65V), Test Circuit - Figure 3 unless otherwise specified. DS200135-8 DS200135-4 FIGURE 7. Speed vs Offset FIGURE 4. Vout vs Vin DS200135-6 FIGURE 8. LM2468 Pulse Response DS200135-7 FIGURE 5. Power Dissipation vs Frequency DS200135-9 FIGURE 9. Speed vs Load Capacitance DS200135-5 FIGURE 6. Speed vs Temperature 3 www.national.com LM2468 Typical Performance Characteristics LM2468 supply and ground pins. A 0.1uF capacitor should be connected from the bias pin (Vbb) to the ground, as close as is practical to the part. THEORY OF OPERATION The LM2468 is a high voltage monolithic three channel CRT driver suitable for color monitor applications. The LM2468 operates with 80V and 12V power supplies. The part is housed in the industry standard 9-lead TO-220 molded plastic power package. ARC PROTECTION During normal CRT operation, internal arcing may occasionally occur. Spark gaps, in the range of 200V, connected from the CRT cathodes to CRT ground will limit the maximum voltage, but to a value that is much higher than allowable on the LM2468. This fast, high voltage, high energy pulse can damage the LM2468 output stage. The application circuit shown in Figure 10 is designed to help clamp the voltage at the output of the LM2468 to a safe level. The clamp diodes, D1 and D2, should have a fast transient response, high peak current rating, low series impedance and low shunt capacitance. FDH400 or equivalent diodes are recommended. Do not use 1N4148 diodes for the clamp diodes. D1 and D2 should have short, low impedance connections to Vcc and ground respectively. The cathode of D1 should be located very close to a separately decoupled bypass capacitor (C3 in Figure 10). The ground connection of D2 and the decoupling capacitor should be very close to the LM2468 ground. This will significantly reduce the high frequency voltage transients that the LM2468 would be subjected to during an arcover condition. Resistor R2 limits the arcover current that is seen by the diodes while R1 limits the current into the LM2468 as well as the voltage stress at the outputs of the device. R2 should be a 1/2W solid carbon type resistor. R1 can be a 1/4W metal or carbon film type resistor. Having large value resistors for R1 and R2 would be desirable, but has the effect of increasing rise and fall times. Inductor L1 is critical to reduce the initial high frequency voltage levels that the LM2468 would be subjected to. The inductor will not only help protect the device, but will also help optimize rise and fall times as well as minimize EMI. For proper arc protection, it is important to not omit any of the arc protection components shown in Figure 10. The circuit diagram of the LM2468 is shown in Figure 1. The PNP emitter follower, Q5, provides input buffering. Q1 and Q2 form a fixed gain cascode amplifier with resistors R1 and R2 setting the gain at -20. Emitter followers Q3 and Q4 isolate the high output impedance of the amplifier from the capacitive load on the output of the amplifier, decreasing the sensitivity of the device to changes in load capacitance. Q6 provides biasing to the output emitter follower stage to reduce crossover distortion at low signal levels. Figure 2 gives the pinout of the LM2468. Figure 3 shows a typical test circuit for evaluation of the LM2468. This circuit is designed to allow testing of the LM2468 in a 50 environment without the use of an expensive FET probe. In this test circuit, two low inductance resistors in series totalling 4.95K form a 200:1 wideband, low capacitance probe when connected to a 50 load (such as 50 oscilloscope input). The input signal from the generator is AC coupled to the base of Q5. APPLICATION HINTS INTRODUCTION National Semiconductor (NSC) is committed to provide application information that assists our customers in obtaining the best performance possible from our products. The following information is provided in order to support this commitment. The reader should be aware that the optimization of performance was done using a specific printed circuit board designed at NSC. Variations in performance can be realized due to physical changes in the printed circuit board and the application. Therefore, the designer should know that component value changes might be required in order to optimize performance in a given application. The values shown in this document can be used as a starting point for evaluation purposes. When working with high bandwidth circuits, good layout practices are always critical to achieving maximum performance. IMPORTANT INFORMATION The LM2468 performance is targeted for the VGA (640 x 480) to XGA (1024 x 768, 60Hz refresh) resolution market. It is designed to be a replacement for discrete CRT drivers. The application circuits shown in this document to optimize performance and to protect against damage from CRT arcover are designed specifically for the LM2468. If another member of the LM246X family is used, please refer to its datasheet. DS200135-10 FIGURE 10. One Video Channel of the LM2468 with the Recommended Arc Protection Circuit OPTIMIZING TRANSIENT RESPONSE Referring to Figure 10, there are three components (R1, R2 and L1) that can be adjusted to optimize the transient response of the application circuit. Increasing the values of R1 and R2 will slow the circuit down while decreasing overshoot. Up to a point, increasing the value of L1 will speed up the circuit as well as increase overshoot. It is very important to use inductors with very high self-resonant frequencies, preferably above 300 MHz. Ferrite core inductors from J.W. Miller Magnetics (part # 78FR39K) were used for optimizing the performance of the device in the NSC application board. The values shown in Figure 10 can be used as a good starting point for the evaluation of the LM2468. If needed, additional damping can be provided by adding a resistor in parallel with L1 to help control overshoot. Using variable POWER SUPPLY BYPASS Since the LM2468 is a wide bandwith amplifier, proper power supply bypassing is critical for optimum performance. Improper power supply bypassing can result in large overshoot, ringing or oscillation. A 0.1uF capacitor should be connected from the supply pin, VCC, to ground, as close to the supply and ground pins as is practical. Additionally, a 10uF to 100uF electrolytic capacitor should be connected from the supply pin to ground. The electrolytic capacitor should also be placed reasonably close to the LM2468's www.national.com 4 LM2468 and from the LM2468 to the CRT cathode should be as short as possible. The following references are recommended: (Continued) resistors for R1 will simplify finding the values needed for optimum performance in a given application. Once the optimum value is determined, the variable resistors can be replaced with fixed values. Ott, Henry W., Noise Reduction Techniques in Electronic Systems, John Wiley & Sons, New York, 1976. Video Amplifier Design for Computer Monitors, National Semiconductor Application Note 1013. Pease, Robert A., Troubleshooting Analog Circuits, Butterworth-Heinemann, 1991. Because of its high small signal bandwith, the part may oscillate in a monitor if feedback occurs around the video channel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input wiring should be spaced as far as possible from output circuit wiring. Effect of Load Capacitance Figure 9 shows the effect of increased load capacitance on the speed of the device. This demonstrates the importance of knowing the load capacitance in the application. Effect of Offset Figure 7 shows the variation in rise and fall times when the output offset of the device is varied from 40VDC to 50VDC. The rise and fall times shows a maximum variation relative to the center data point (45VDC) of about 7%. NSC Demonstration Board Figure 13 shows the routing and component placement on the NSC LM126X/246X demonstration board. The schematic of the board is shown in Figures 11, 12. This board provides a good example of a layout that can be used as a guide for future layouts. Note the location of the following components: * C16, C19 -- VCC bypass capacitor, located very close to pin 4 and the ground plane near the device. * C20 -- VBB bypass capacitors, located close to pin 8 and ground. * C46, C47, C48 -- VCC bypass capacitors, near LM2468 VCC clamp diodes. Very important for arc protection. The routing of the LM2468 video outputs to the CRT is very critical to achieving optimum performance. Figure 13 shows the routing and component placement from pin 3 of the LM2468 to the blue cathode. Note that the components are placed so that they almost line up from the output pin of the LM2468 to the blue cathode pin of the CRT connector. This is done to minimize the length of the video path between these two components. Note also that D8, D9, R24, and D6 are placed to minimize the size of the video nodes that they are attached to. This minimizes parasitic capacitance in the video path and also enhances the effectiveness of the protection diodes. The anode of protection diode D8 is connected directly to a section of the ground plane that has a short and direct path to the LM2468 ground pins. The cathode of D9 is connected to VCC very close to decoupling capacitor C48 (near the center of Figure 13), which is connected to the same section of the ground plane as D8. The diode placement and routing is very important for minimizing the voltage stress on the LM2468 video outputs during an arc over event. Lastly, notice that S3 is placed very close to the blue cathode and is tied directly to the ground under the CRT connector. THERMAL CONSIDERATIONS Figure 6 shows the performance of the LM2468 video amplifiers in the test circuit shown in Figure 3 as a function of case temperature. The figure shows that the rise time of the LM2468 increases by approximately 9% as the case temperature increases from 30C to 100C. This corresponds to a speed degradation of 1.3% for every 10C rise in case temperature. The fall time degrades around 0.6% for every 10C in case temperature. Figure 5 shows the maximum power dissipation of the LM2468 vs. Frequency when all three channels of the device are driving an 8pF load with a 40 Vp-p signal alternating one pixel on, one pixel off. The graph assumes a 72% active time (device operating at the specified frequency) which is typical in a monitor application. The other 28% of the time the device is assumed to be sitting at the black level (65V in this case). This graph gives the designer the information needed to determine the heat sink requirement for his application. The designer should note that if the load capacitance is increased, the AC component of the total power dissipation will also increase. The LM2468 case temperature must be maintained below 115C. If the maximum expected ambient temperature is 70C and the maximum power dissipation is 2.95W (from Figure 5, 50 MHz bandwith), then a maximum heat sink thermal resistance can be calculated: This example assumes a capacitive load of 8pF and no resistive load. TYPICAL APPLICATION A typical application of the LM2468 is shown in Figures 11, 12. Used in conjunction with an LM1269 coupled with an LM2479/2480 bias clamp, a complete video channel from monitor input to CRT cathode can be achieved. Performance is ideal for 1024x768 resolution displays with pixel clock frequencies up to 50 MHz. Figures 11, 12 are the schematic for the NSC demonstration board that can be used to evaluate the LM1269/2468 combination in a monitor. PC Board Layout Considerations For optimum performance, an adequate ground plane, isolation between channels, good supply bypassing and the minimization of unwanted feedback are necessary. Also, the length of the signal traces from the preamplifier to the 5 www.national.com LM2468 APPLICATION HINTS FIGURE 11. LM1269/2468 Demonstration Board Schematic DS200135-29 LM2468 APPLICATION HINTS www.national.com (Continued) 6 DS200135-30 (Continued) LM2468 FIGURE 12. LM1269/2468 Demonstration Board Schematic (continued) APPLICATION HINTS 7 www.national.com LM2468 APPLICATION HINTS (Continued) DS200135-17 FIGURE 13. NSC LM126X/246X Demo Board Layout www.national.com 8 LM2468 Monolothic Triple 14nS High Gain CRT Driver Physical Dimensions inches (millimeters) unless otherwise noted Note: Information contained in this data sheet is preliminary and may be subject to change without notice. NS Package Number TA09A Order Number LM2468TA LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.