INDUCTORS
VLS201610E-CA
VLS201612E-CA
VLS2010E-CA
VLS2012E-CA
VLS252008E-CA
VLS252010E-CA
VLS252012E-CA
VLS252015E-CA
VLS3010E-CA
VLS3012E-CA
VLS3015E-CA
VLS4012E-CA
February 2014
Inductors for Power Circuits
Wound Ferrite
VLS-E-CA
series
(For automobiles)
(2/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
Inductors for Power Circuits
Wound Ferrite
FEATURES
Magnetic shield type wound inductor for power circuits.
Low-profile product lineup with max. heights of 0.8mm, 0.95mm, 1.0mm, 1.2mm, and 1.5mm allowing for different usages.
High magnetic shield construction and compatible with high-density mounting.
APPLICATION
Car navigation, car stereo and car accessories only
Not available for use related to driving, curving, stopping, and the other safety.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the VLS-E-CA Series
VLS 201610 E T -R47 N -CA
Series name L×W×H Dimensions internal code Packaging style Inductance Inductance
tolerance Internal code
(mm) (μH)
201610 2.0×1.6×1.0 T Taping R47 0.47
201612 2.0×1.6×1.2 2R2 2.2
2010 2.0×2.0×1.0 100 10
2012 2.0×2.0×1.2
252008 2.5×2.0×0.8
252010 2.5×2.0×1.0
252012 2.5×2.0×1.2
252015 2.5×2.0×1.5
3010 3.0×3.0×1.0
3012 3.0×3.0×1.2
3015 3.0×3.0×1.5
4012 4.0×4.0×1.2
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
VLS201610E-CA –40 to +105 –40 to +105 2000 12
VLS201612E-CA –40 to +105 –40 to +105 2000 14
VLS2010E-CA –40 to +105 –40 to +105 2000 16
VLS2012E-CA –40 to +105 –40 to +105 2000 17
VLS252008E-CA –40 to +105 –40 to +105 2000 15
VLS252010E-CA –40 to +105 –40 to +105 2000 17
VLS252012E-CA –40 to +105 –40 to +105 2000 24
VLS252015E-CA –40 to +105 –40 to +105 2000 28
VLS3010E-CA –40 to +105 –40 to +105 2000 36
VLS3012E-CA –40 to +105 –40 to +105 2000 40
VLS3015E-CA –40 to +105 –40 to +105 2000 52
VLS4012E-CA –40 to +105 –40 to +105 1000 67
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
Overview of the VLS-E-CA Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30s 260°C 10s
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS201610E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
2.0±0.1
1.6±0.1
0.95max.
(0.65)(
0.65)(0.7)
Dimensions in mm
Dimensions in mm
0.65 0.7 0.65
1.6
(6/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201610E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30%1.0 0.065 0.054 1.85 2.10 1.95 VLS201610ET-R47N-CA
0.68 ±30%1.0 0.086 0.072 1.65 1.85 1.65 VLS201610ET-R68N-CA
1.0 ±30%1.0 0.119 0.099 1.35 1.50 1.40 VLS201610ET-1R0N-CA
1.5 ±30%1.0 0.181 0.151 1.10 1.20 1.15 VLS201610ET-1R5N-CA
2.2 ±20%1.0 0.276 0.230 0.94 1.05 0.95 VLS201610ET-2R2M-CA
3.3 ±20%1.0 0.458 0.382 0.75 0.84 0.73 VLS201610ET-3R3M-CA
4.7 ±20%1.0 0.554 0.462 0.64 0.72 0.67 VLS201610ET-4R7M-CA
6.8 ±20%1.0 0.840 0.700 0.53 0.59 0.54 VLS201610ET-6R8M-CA
10 ±20%1.0 1.380 1.150 0.40 0.45 0.42 VLS201610ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(7/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201610E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(8/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201610E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(9/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS201612E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.2max.
2.0±0.1
1.6±0.1
(0.65)(
0.65)(0.7)
Dimensions in mm
Dimensions in mm
0.65 0.7 0.65
1.6
(10/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201612E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30% 1.0 0.063 0.052 1.90 2.15 2.00 VLS201612ET-R47N-CA
0.68 ±30% 1.0 0.072 0.060 1.70 1.90 1.85 VLS201612ET-R68N-CA
1.0 ±30% 1.0 0.093 0.077 1.50 1.65 1.65 VLS201612ET-1R0N-CA
1.5 ±30% 1.0 0.159 0.132 1.20 1.30 1.25 VLS201612ET-1R5N-CA
2.2 ±20% 1.0 0.195 0.162 1.05 1.15 1.15 VLS201612ET-2R2M-CA
3.3 ±20% 1.0 0.357 0.297 0.79 0.88 0.85 VLS201612ET-3R3M-CA
4.7 ±20% 1.0 0.438 0.365 0.70 0.78 0.75 VLS201612ET-4R7M-CA
6.8 ±20% 1.0 0.708 0.590 0.58 0.65 0.60 VLS201612ET-6R8M-CA
10 ±20% 1.0 1.026 0.855 0.47 0.53 0.50 VLS201612ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(11/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201612E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(12/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS201612E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(13/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS2010E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.0max. 2.0±0.1
(0.65)(
0.65)(0.7)
2.0±0.1
Dimensions in mm
Dimensions in mm
0.65 0.7 0.65
2.0
(14/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2010E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.56 ±30% 1.0 0.060 0.050 2.00 2.25 2.05 VLS2010ET-R56N-CA
1.0 ±30% 1.0 0.108 0.090 1.45 1.65 1.55 VLS2010ET-1R0N-CA
1.5 ±30% 1.0 0.156 0.130 1.20 1.30 1.25 VLS2010ET-1R5N-CA
2.2 ±20% 1.0 0.228 0.190 1.00 1.10 1.05 VLS2010ET-2R2M-CA
3.3 ±20% 1.0 0.348 0.290 0.83 0.93 0.86 VLS2010ET-3R3M-CA
4.7 ±20% 1.0 0.408 0.340 0.70 0.78 0.79 VLS2010ET-4R7M-CA
6.8 ±20% 1.0 0.648 0.540 0.57 0.64 0.63 VLS2010ET-6R8M-CA
10 ±20% 1.0 0.936 0.780 0.47 0.52 0.52 VLS2010ET-100M-CA
15 ±20% 1.0 1.476 1.230 0.40 0.44 0.41 VLS2010ET-150M-CA
22 ±20% 1.0 2.040 1.700 0.33 0.37 0.35 VLS2010ET-220M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(15/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2010E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.01 0.1 1 10 100 1000
Frequency(MHz)
Inductance(μH)
0.01
0.1
1
10
100
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R56N
150M
220M
Product No. Manufacturer
4294A Agilent Technologies
(16/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2010E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R56N
150M
220M
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(17/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS2012E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.2max. 2.0±0.1
(0.65)(
0.65)(0.7)
2.0±0.1
Dimensions in mm
Dimensions in mm
0.65 0.7 0.65
2.0
(18/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2012E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30% 1.0 0.059 0.049 2.05 2.25 2.00 VLS2012ET-R47N-CA
0.68 ±30% 1.0 0.066 0.055 1.70 1.90 1.85 VLS2012ET-R68N-CA
1.0 ±30% 1.0 0.086 0.071 1.45 1.65 1.65 VLS2012ET-1R0N-CA
1.5 ±30% 1.0 0.108 0.090 1.20 1.30 1.45 VLS2012ET-1R5N-CA
2.2 ±20% 1.0 0.153 0.127 1.00 1.10 1.25 VLS2012ET-2R2M-CA
3.3 ±20% 1.0 0.228 0.190 0.84 0.93 1.00 VLS2012ET-3R3M-CA
4.7 ±20% 1.0 0.336 0.280 0.70 0.78 0.84 VLS2012ET-4R7M-CA
6.8 ±20% 1.0 0.498 0.415 0.57 0.64 0.69 VLS2012ET-6R8M-CA
10 ±20% 1.0 0.834 0.695 0.47 0.52 0.53 VLS2012ET-100M-CA
15 ±20% 1.0 1.062 0.885 0.40 0.44 0.47 VLS2012ET-150M-CA
22 ±20% 1.0 1.764 1.470 0.33 0.37 0.35 VLS2012ET-220M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(19/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2012E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.001
0.01
0.1
Inductance(μH)
1
10
100
0.1 1 10 100 1000
Frequency(MHz)
100M
6R8M
4R7M
3R3M
150M
220M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(20/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS2012E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
150M
220M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(21/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS252008E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
2.5±0.1 (0.85)(
0.85)(0.8)
2.0±0.1
0.8max.
Dimensions in mm
Dimensions in mm
0.85 0.8 0.85
2.0
(22/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252008E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30% 1.0 0.140 0.116 1.65 1.80 1.20 VLS252008ET-R47N-CA
1.0 ±30% 1.0 0.219 0.182 1.20 1.35 0.97 VLS252008ET-1R0N-CA
1.5 ±30% 1.0 0.248 0.206 1.00 1.10 0.91 VLS252008ET-1R5N-CA
2.2 ±20% 1.0 0.290 0.241 0.77 0.86 0.84 VLS252008ET-2R2M-CA
3.3 ±20% 1.0 0.416 0.346 0.73 0.82 0.70 VLS252008ET-3R3M-CA
4.7 ±20% 1.0 0.580 0.483 0.61 0.68 0.59 VLS252008ET-4R7M-CA
6.8 ±20% 1.0 0.818 0.681 0.49 0.55 0.50 VLS252008ET-6R8M-CA
10.0 ±20% 1.0 1.232 1.026 0.43 0.48 0.41 VLS252008ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(23/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252008E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(24/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252008E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(25/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS252010E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.0max.
2.5±0.1 (0.85)(
0.85)(0.8)
2.0±0.1
Dimensions in mm
Dimensions in mm
0.85 0.8 0.85
2.0
(26/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252010E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30% 1.0 0.046 0.038 2.50 2.80 2.65 VLS252010ET-R47N-CA
0.68 ±30% 1.0 0.062 0.052 2.05 2.30 2.20 VLS252010ET-R68N-CA
1.0 ±30% 1.0 0.084 0.070 1.75 1.90 1.90 VLS252010ET-1R0N-CA
1.5 ±30% 1.0 0.128 0.107 1.45 1.60 1.50 VLS252010ET-1R5N-CA
2.2 ±20% 1.0 0.190 0.158 1.20 1.30 1.20 VLS252010ET-2R2M-CA
3.3 ±20% 1.0 0.275 0.229 0.94 1.05 1.00 VLS252010ET-3R3M-CA
4.7 ±20% 1.0 0.398 0.332 0.80 0.89 0.82 VLS252010ET-4R7M-CA
6.8 ±20% 1.0 0.532 0.443 0.68 0.76 0.71 VLS252010ET-6R8M-CA
10 ±20% 1.0 0.854 0.712 0.56 0.63 0.55 VLS252010ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(27/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252010E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0.01 0.1 1 10 100 1000
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(28/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252010E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 32.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R68N R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(29/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS252012E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.2max.
2.5±0.1 (0.85)(
0.85)(0.8)
2.0±0.1
Dimensions in mm
Dimensions in mm
0.85 0.8 0.85
2.0
(30/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252012E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
0.47 ±30% 1.0 0.056 0.047 2.75 3.10 2.15 VLS252012ET-R47N-CA
1.0 ±30% 1.0 0.087 0.073 2.20 2.45 1.70 VLS252012ET-1R0N-CA
1.5 ±30% 1.0 0.126 0.105 1.80 2.00 1.45 VLS252012ET-1R5N-CA
2.2 ±20% 1.0 0.154 0.129 1.55 1.75 1.30 VLS252012ET-2R2M-CA
3.3 ±20% 1.0 0.272 0.227 1.25 1.40 0.98 VLS252012ET-3R3M-CA
4.7 ±20% 1.0 0.405 0.338 1.05 1.20 0.81 VLS252012ET-4R7M-CA
6.8 ±20% 1.0 0.612 0.510 0.85 0.95 0.65 VLS252012ET-6R8M-CA
10 ±20% 1.0 0.756 0.630 0.73 0.82 0.59 VLS252012ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(31/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252012E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R47N
Product No. Manufacturer
4294A Agilent Technologies
(32/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252012E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 42.5 3 3.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
R47N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(33/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS252015E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.5max.
2.5±0.1 (0.85)(
0.85)(0.8)
2.0±0.1
Dimensions in mm
Dimensions in mm
0.85 0.8 0.85
2.0
(34/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252015E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
1.0 ±30% 1.0 0.082 0.068 1.95 2.20 1.75 VLS252015ET-1R0N-CA
1.5 ±30% 1.0 0.120 0.100 1.75 1.95 1.45 VLS252015ET-1R5N-CA
2.2 ±20% 1.0 0.160 0.133 1.50 1.70 1.25 VLS252015ET-2R2M-CA
3.3 ±20% 1.0 0.219 0.182 1.20 1.35 1.05 VLS252015ET-3R3M-CA
4.7 ±20% 1.0 0.318 0.265 1.00 1.15 0.89 VLS252015ET-4R7M-CA
6.8 ±20% 1.0 0.480 0.400 0.85 0.95 0.73 VLS252015ET-6R8M-CA
10 ±20% 1.0 0.588 0.490 0.72 0.80 0.66 VLS252015ET-100M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(35/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252015E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.01
0.1
1
10
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4294A Agilent Technologies
(36/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS252015E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M 4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(37/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS3010E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
3.0±0.1
3.0±0.1
1.0max.
(0.9)(
0.9)(1.2)
Dimensions in mm
Dimensions in mm
1.0 1.0 1.0
3.0
(38/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3010E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
1.0 ±30% 1.0 0.072 0.060 1.60 1.80 2.10 VLS3010ET-1R0N-CA
1.5 ±30% 1.0 0.085 0.071 1.35 1.50 1.90 VLS3010ET-1R5N-CA
2.2 ±20% 1.0 0.116 0.097 1.20 1.30 1.70 VLS3010ET-2R2M-CA
3.3 ±20% 1.0 0.156 0.130 1.00 1.10 1.50 VLS3010ET-3R3M-CA
4.7 ±20% 1.0 0.204 0.170 0.81 0.90 1.30 VLS3010ET-4R7M-CA
6.8 ±20% 1.0 0.312 0.260 0.69 0.77 1.00 VLS3010ET-6R8M-CA
10 ±20% 1.0 0.468 0.390 0.56 0.63 0.80 VLS3010ET-100M-CA
15 ±20% 1.0 0.612 0.510 0.48 0.54 0.70 VLS3010ET-150M-CA
22 ±20% 1.0 0.900 0.750 0.38 0.43 0.60 VLS3010ET-220M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(39/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3010E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
220M
150M
Product No. Manufacturer
4294A Agilent Technologies
(40/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3010E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
220M
150M
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(41/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS3012E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.2max.
3.0±0.1
3.0±0.1
(0.9)(
0.9)(1.2)
Dimensions in mm
Dimensions in mm
1.0 1.0 1.0
3.0
(42/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3012E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
1.0 ±30% 1.0 0.068 0.056 1.90 2.15 2.00 VLS3012ET-1R0N-CA
1.5 ±30% 1.0 0.076 0.063 1.50 1.70 1.85 VLS3012ET-1R5N-CA
2.2 ±20% 1.0 0.096 0.080 1.35 1.50 1.70 VLS3012ET-2R2M-CA
3.3 ±20% 1.0 0.120 0.100 1.05 1.20 1.55 VLS3012ET-3R3M-CA
4.7 ±20% 1.0 0.156 0.130 0.95 1.05 1.30 VLS3012ET-4R7M-CA
6.8 ±20% 1.0 0.228 0.190 0.81 0.90 1.05 VLS3012ET-6R8M-CA
10 ±20% 1.0 0.336 0.280 0.64 0.76 0.89 VLS3012ET-100M-CA
15 ±20% 1.0 0.516 0.430 0.55 0.62 0.74 VLS3012ET-150M-CA
22 ±20% 1.0 0.756 0.630 0.44 0.49 0.61 VLS3012ET-220M-CA
33 ±20% 1.0 1.248 1.040 0.37 0.41 0.48 VLS3012ET-330M-CA
47 ±20% 1.0 1.500 1.250 0.31 0.35 0.44 VLS3012ET-470M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(43/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3012E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
1000
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
330M
6R8M
100M
150M
220M
470M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4294A Agilent Technologies
(44/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3012E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5 3
DC current(A)
100M
6R8M
4R7M
3R3M
150M
220M
2R2M
1R5N
1R0N
470M
330M
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(45/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS3015E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.5max.
3.0±0.1
3.0±0.1
(0.9)(
0.9)(1.2)
Dimensions in mm
Dimensions in mm
1.0 1.0 1.0
3.0
(46/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3015E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
1.0 ±30% 1.0 0.058 0.048 2.00 2.20 2.10 VLS3015ET-1R0N-CA
1.5 ±30% 1.0 0.075 0.062 1.50 1.70 1.85 VLS3015ET-1R5N-CA
2.2 ±20% 1.0 0.084 0.070 1.35 1.50 1.75 VLS3015ET-2R2M-CA
3.3 ±20% 1.0 0.112 0.093 1.15 1.30 1.50 VLS3015ET-3R3M-CA
4.7 ±20% 1.0 0.136 0.113 1.00 1.10 1.35 VLS3015ET-4R7M-CA
6.8 ±20% 1.0 0.216 0.180 0.92 1.00 1.05 VLS3015ET-6R8M-CA
10 ±20% 1.0 0.288 0.240 0.70 0.78 0.94 VLS3015ET-100M-CA
15 ±20% 1.0 0.456 0.380 0.58 0.65 0.75 VLS3015ET-150M-CA
22 ±20% 1.0 0.660 0.550 0.48 0.54 0.62 VLS3015ET-220M-CA
33 ±20% 1.0 0.984 0.820 0.39 0.43 0.51 VLS3015ET-330M-CA
47 ±20% 1.0 1.500 1.250 0.32 0.35 0.41 VLS3015ET-470M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(47/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3015E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
1000
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
150M
220M
470M
330M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4294A Agilent Technologies
(48/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS3015E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5
DC current(A)
100M
6R8M
150M
220M
470M
330M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(49/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
VLS4012E-CA Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
4.0±0.1
4.0±0.1
1.2max.
(1.3)(
1.3)(1.4)
Dimensions in mm
Dimensions in mm
1.3 1.4 1.3
4.0
(50/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS4012E-CA Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the nominal value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LMeasuring
frequency
(MHz)
DC resistance
()
Rated current(A)
Part No.
max. typ.
(μH) Tolerance max. typ. Idc1 Idc1 Idc2
1.0 ±30% 1.0 0.060 0.050 2.50 2.80 2.65 VLS4012ET-1R0N-CA
1.5 ±30% 1.0 0.072 0.060 2.10 2.30 2.45 VLS4012ET-1R5N-CA
2.2 ±20% 1.0 0.081 0.067 1.70 1.90 2.20 VLS4012ET-2R2M-CA
3.3 ±20% 1.0 0.102 0.085 1.40 1.60 2.00 VLS4012ET-3R3M-CA
4.7 ±20% 1.0 0.118 0.098 1.20 1.40 1.90 VLS4012ET-4R7M-CA
6.8 ±20% 1.0 0.156 0.130 1.00 1.20 1.60 VLS4012ET-6R8M-CA
10 ±20% 1.0 0.228 0.190 0.89 0.99 1.33 VLS4012ET-100M-CA
15 ±20% 1.0 0.372 0.310 0.70 0.78 1.05 VLS4012ET-150M-CA
22 ±20% 1.0 0.468 0.390 0.63 0.70 0.95 VLS4012ET-220M-CA
33 ±20% 1.0 0.804 0.670 0.47 0.53 0.70 VLS4012ET-330M-CA
47 ±20% 1.0 1.020 0.850 0.41 0.46 0.61 VLS4012ET-470M-CA
Measurement item Product No. Manufacturer
L 4194A Agilent Technologies
DC resistance VP-2941A Panasonic
Rated current Idc1 4285A+42841A+42842C Agilent Technologies
(51/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS4012E-CA Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
1000
100
0.01 0.1 1 10 100 1000
Inductance(μH)
Frequency(MHz)
100M
6R8M
150M
220M
470M
330M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4294A Agilent Technologies
(52/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series VLS4012E-CA Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1
1
10
100
Inductance(μH)
0 0.5 1 1.5 2 2.5 3 3.5
DC current(A)
100M
6R8M
150M
220M
470M
330M
4R7M
3R3M
2R2M
1R5N
1R0N
Product No. Manufacturer
4285A+42841A+42842C Agilent Technologies
(53/53)
INDUCTORS
001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm
• All specifications are subject to change without notice.
VLS-E-CA series
Packaging Style
REEL DIMENSIONS
* These values are typical values.
TAPE DIMENSIONS
Ty p e AW1 W2 N E
VLS201610E-CA ø180 9 13 ø60 0.5
VLS201612E-CA ø180 9 13 ø60 0.5
VLS2010E-CA ø180 9 13 ø60 0.5
VLS2012E-CA ø180 9 13 ø60 0.5
VLS252008E-CA ø180 9 13 ø60 0.5
VLS252010E-CA ø180 9 13 ø60 0.5
VLS252012E-CA ø180 9 13 ø60 0.5
VLS252015E-CA ø180 9 13 ø60 0.5
VLS3010E-CA ø180 9 13 ø60 0.5
VLS3012E-CA ø180 9 13 ø60 0.5
VLS3015E-CA ø180 9 13 ø60 0.5
VLS4012E-CA ø180 13 17 ø60 0.5
ø13.0±0.5
ø21.0±0.8
2.0±0.5
A
(1.0)
Dimensions in mm
N
E
W2
W1
FE
W
P0P2øD0 P1
At
B
K
Dimensions in mm
Ty p e A B øD0 E F P0 P1 P2 W K t
VLS201610E-CA 1.8 2.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.1 0.25
VLS201612E-CA 1.8 2.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.3 0.25
VLS2010E-CA 2.2 2.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.1 0.25
VLS2012E-CA 2.2 2.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.35 0.25
VLS252008E-CA 2.15 2.7 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 0.95 0.25
VLS252010E-CA 2.15 2.7 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.15 0.3
VLS252012E-CA 2.15 2.7 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.35 0.3
VLS252015E-CA 2.15 2.7 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.65 0.3
VLS3010E-CA 3.2 3.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.15 0.25
VLS3012E-CA 3.2 3.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.35 0.25
VLS3015E-CA 3.2 3.2 1.5+0.10/-0 1.75±0.1 3.5±0.05 4.0±0.1 4.0±0.1 2.00±0.05 8.0±0.2 1.65 0.25
VLS4012E-CA 4.25 4.25 1.5+0.10/-0 1.75±0.1 5.5±0.05 4.0±0.1 8.0±0.1 2.00±0.05 12.0±0.2 1.35 0.3
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TDK:
VLS3015ET-4R7M-CA VLS4012ET-6R8M-CA VLS2010ET-2R2M-CA VLS2012ET-2R2M-CA VLS3010ET-3R3M-CA
VLS252008ET-1R5N-CA VLS2012ET-3R3M-CA VLS252010ET-100M-CA VLS4012ET-2R2M-CA VLS2012ET-
4R7M-CA VLS252008ET-3R3M-CA VLS3010ET-1R0N-CA VLS3010ET-150M-CA VLS252008ET-4R7M-CA
VLS4012ET-1R5N-CA VLS4012ET-150M-CA VLS3015ET-330M-CA VLS201610ET-2R2M-CA VLS201612ET-2R2M-
CA VLS3015ET-1R0N-CA VLS2010ET-150M-CA VLS4012ET-220M-CA VLS3010ET-4R7M-CA VLS3012ET-4R7M-
CA VLS3015ET-100M-CA VLS3015ET-220M-CA VLS3012ET-1R0N-CA VLS201610ET-100M-CA VLS2012ET-
1R5N-CA VLS201612ET-100M-CA VLS252010ET-R68N-CA VLS3012ET-6R8M-CA VLS252008ET-1R0N-CA
VLS3010ET-6R8M-CA VLS4012ET-4R7M-CA VLS3015ET-150M-CA VLS3012ET-220M-CA VLS2012ET-220M-CA
VLS3010ET-1R5N-CA VLS3010ET-220M-CA VLS3010ET-100M-CA VLS3015ET-2R2M-CA VLS3012ET-3R3M-CA
VLS4012ET-3R3M-CA VLS3012ET-470M-CA VLS2010ET-100M-CA VLS3015ET-6R8M-CA VLS2012ET-R47N-CA
VLS3012ET-330M-CA VLS252008ET-R47N-CA VLS252010ET-2R2M-CA VLS2010ET-1R5N-CA VLS2010ET-6R8M-
CA VLS252008ET-100M-CA VLS252008ET-2R2M-CA VLS2012ET-100M-CA VLS2010ET-4R7M-CA VLS3015ET-
3R3M-CA VLS2012ET-R68N-CA VLS3012ET-1R5N-CA VLS2010ET-1R0N-CA VLS3012ET-100M-CA VLS4012ET-
330M-CA VLS2010ET-R56N-CA VLS3012ET-2R2M-CA VLS4012ET-470M-CA VLS4012ET-1R0N-CA VLS4012ET-
100M-CA VLS252015ET-100M-CA VLS2012ET-1R0N-CA VLS3010ET-2R2M-CA VLS252008ET-6R8M-CA
VLS3015ET-470M-CA VLS2010ET-3R3M-CA VLS3015ET-1R5N-CA VLS2012ET-150M-CA VLS252012ET-100M-CA
VLS3012ET-150M-CA VLS2012ET-6R8M-CA VLS2010ET-220M-CA VLS201612ET-R68N-CA VLS252015ET-
6R8M-CA VLS201612ET-3R3M-CA VLS201612ET-6R8M-CA VLS201612ET-1R0N-CA VLS201612ET-1R5N-CA
VLS201612ET-4R7M-CA VLS252015ET-1R0N-CA VLS252015ET-1R5N-CA VLS252015ET-3R3M-CA
VLS201612ET-R47N-CA VLS252015ET-2R2M-CA VLS252015ET-4R7M-CA
