I N D U C T O R S February 2014 Inductors for Power Circuits Wound Ferrite VLS-E-CA series VLS201610E-CA VLS201612E-CA VLS2010E-CA VLS2012E-CA VLS252008E-CA VLS252010E-CA VLS252012E-CA VLS252015E-CA VLS3010E-CA VLS3012E-CA VLS3015E-CA VLS4012E-CA (For automobiles) (2/53) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (3/53) I N D U C T O R S Inductors for Power Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Wound Ferrite Overview of the VLS-E-CA Series FEATURES Magnetic shield type wound inductor for power circuits. Low-profile product lineup with max. heights of 0.8mm, 0.95mm, 1.0mm, 1.2mm, and 1.5mm allowing for different usages. High magnetic shield construction and compatible with high-density mounting. APPLICATION Car navigation, car stereo and car accessories only Not available for use related to driving, curving, stopping, and the other safety. PART NUMBER CONSTRUCTION VLS Series name 201610 LxWxH Dimensions (mm) 201610 2.0x1.6x1.0 201612 2.0x1.6x1.2 2010 2.0x2.0x1.0 2012 2.0x2.0x1.2 252008 2.5x2.0x0.8 252010 2.5x2.0x1.0 252012 2.5x2.0x1.2 252015 2.5x2.0x1.5 3010 3.0x3.0x1.0 3012 3.0x3.0x1.2 3015 3.0x3.0x1.5 4012 4.0x4.0x1.2 E T internal code Packaging style T - Taping R47 N Inductance (H) R47 0.47 2R2 2.2 100 10 Inductance tolerance - CA Internal code OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) C C VLS201610E-CA -40 to +105 -40 to +105 2000 VLS201612E-CA -40 to +105 -40 to +105 2000 VLS2010E-CA -40 to +105 -40 to +105 2000 VLS2012E-CA -40 to +105 -40 to +105 2000 VLS252008E-CA -40 to +105 -40 to +105 2000 VLS252010E-CA -40 to +105 -40 to +105 2000 VLS252012E-CA -40 to +105 -40 to +105 2000 VLS252015E-CA -40 to +105 -40 to +105 2000 VLS3010E-CA -40 to +105 -40 to +105 2000 VLS3012E-CA -40 to +105 -40 to +105 2000 VLS3015E-CA -40 to +105 -40 to +105 2000 VLS4012E-CA -40 to +105 -40 to +105 1000 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Individual weight mg 12 14 16 17 15 17 24 28 36 40 52 67 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (4/53) I N D U C T O R S Overview of the VLS-E-CA Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30s Peak Temp. T4 260C Time t3 10s * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (5/53) I N D U C T O R S VLS-E-CA series VLS201610E-CA Type 1.60.1 SHAPE & DIMENSIONS (0.65) 0.95max. 2.00.1 (0.7) (0.65) Dimensions in mm 1.6 RECOMMENDED LAND PATTERN 0.65 0.7 0.65 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (6/53) I N D U C T O R S VLS-E-CA series VLS201610E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 Tolerance 30% 30% 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.065 0.054 0.086 0.072 0.119 0.099 0.181 0.151 0.276 0.230 0.458 0.382 0.554 0.462 0.840 0.700 1.380 1.150 Rated current(A) max. typ. Idc1 Idc1 1.85 2.10 1.65 1.85 1.35 1.50 1.10 1.20 0.94 1.05 0.75 0.84 0.64 0.72 0.53 0.59 0.40 0.45 Part No. Idc2 1.95 1.65 1.40 1.15 0.95 0.73 0.67 0.54 0.42 VLS201610ET-R47N-CA VLS201610ET-R68N-CA VLS201610ET-1R0N-CA VLS201610ET-1R5N-CA VLS201610ET-2R2M-CA VLS201610ET-3R3M-CA VLS201610ET-4R7M-CA VLS201610ET-6R8M-CA VLS201610ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (7/53) I N D U C T O R S VLS-E-CA series VLS201610E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M Inductance(H) 10 4R7M 3R3M 2R2M 1R5N 1R0N 1 R68N R47N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (8/53) I N D U C T O R S VLS-E-CA series VLS201610E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 100M Inductance(H) 10 6R8M 4R7M 3R3M 2R2M 1R5N 1R0N 1 R68N R47N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (9/53) I N D U C T O R S VLS-E-CA series VLS201612E-CA Type 1.60.1 SHAPE & DIMENSIONS (0.65) 1.2max. 2.00.1 (0.7) (0.65) Dimensions in mm 1.6 RECOMMENDED LAND PATTERN 0.65 0.7 0.65 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (10/53) I N D U C T O R S VLS-E-CA series VLS201612E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 Tolerance 30% 30% 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.063 0.052 0.072 0.060 0.093 0.077 0.159 0.132 0.195 0.162 0.357 0.297 0.438 0.365 0.708 0.590 1.026 0.855 Rated current(A) max. typ. Idc1 Idc1 1.90 2.15 1.70 1.90 1.50 1.65 1.20 1.30 1.05 1.15 0.79 0.88 0.70 0.78 0.58 0.65 0.47 0.53 Part No. Idc2 2.00 1.85 1.65 1.25 1.15 0.85 0.75 0.60 0.50 VLS201612ET-R47N-CA VLS201612ET-R68N-CA VLS201612ET-1R0N-CA VLS201612ET-1R5N-CA VLS201612ET-2R2M-CA VLS201612ET-3R3M-CA VLS201612ET-4R7M-CA VLS201612ET-6R8M-CA VLS201612ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (11/53) I N D U C T O R S VLS-E-CA series VLS201612E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M 4R7M Inductance(H) 10 3R3M 2R2M 1R5N 1R0N 1 R68N R47N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (12/53) I N D U C T O R S VLS-E-CA series VLS201612E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R68N R47N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (13/53) I N D U C T O R S VLS-E-CA series VLS2010E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.65) (0.7) (0.65) 1.0max. 2.00.1 Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.65 0.7 0.65 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (14/53) I N D U C T O R S VLS-E-CA series VLS2010E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.56 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Tolerance 30% 30% 30% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.060 0.050 0.108 0.090 0.156 0.130 0.228 0.190 0.348 0.290 0.408 0.340 0.648 0.540 0.936 0.780 1.476 1.230 2.040 1.700 Rated current(A) max. typ. Idc1 Idc1 2.00 2.25 1.45 1.65 1.20 1.30 1.00 1.10 0.83 0.93 0.70 0.78 0.57 0.64 0.47 0.52 0.40 0.44 0.33 0.37 Part No. Idc2 2.05 1.55 1.25 1.05 0.86 0.79 0.63 0.52 0.41 0.35 VLS2010ET-R56N-CA VLS2010ET-1R0N-CA VLS2010ET-1R5N-CA VLS2010ET-2R2M-CA VLS2010ET-3R3M-CA VLS2010ET-4R7M-CA VLS2010ET-6R8M-CA VLS2010ET-100M-CA VLS2010ET-150M-CA VLS2010ET-220M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (15/53) I N D U C T O R S VLS-E-CA series VLS2010E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 220M 150M 100M 6R8M Inductance(H) 10 4R7M 3R3M 2R2M 1R5N 1R0N 1 R56N 0.1 0.01 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (16/53) I N D U C T O R S VLS-E-CA series VLS2010E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 220M 150M Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R56N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (17/53) I N D U C T O R S VLS-E-CA series VLS2012E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.65) (0.7) (0.65) 1.2max. 2.00.1 Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.65 0.7 0.65 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (18/53) I N D U C T O R S VLS-E-CA series VLS2012E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Tolerance 30% 30% 30% 30% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.059 0.049 0.066 0.055 0.086 0.071 0.108 0.090 0.153 0.127 0.228 0.190 0.336 0.280 0.498 0.415 0.834 0.695 1.062 0.885 1.764 1.470 Rated current(A) max. typ. Idc1 Idc1 2.05 2.25 1.70 1.90 1.45 1.65 1.20 1.30 1.00 1.10 0.84 0.93 0.70 0.78 0.57 0.64 0.47 0.52 0.40 0.44 0.33 0.37 Part No. Idc2 2.00 1.85 1.65 1.45 1.25 1.00 0.84 0.69 0.53 0.47 0.35 VLS2012ET-R47N-CA VLS2012ET-R68N-CA VLS2012ET-1R0N-CA VLS2012ET-1R5N-CA VLS2012ET-2R2M-CA VLS2012ET-3R3M-CA VLS2012ET-4R7M-CA VLS2012ET-6R8M-CA VLS2012ET-100M-CA VLS2012ET-150M-CA VLS2012ET-220M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (19/53) I N D U C T O R S VLS-E-CA series VLS2012E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 220M 150M 100M 6R8M 4R7M 10 3R3M 2R2M 1R5N 1R0N 1 Inductance(H) R68N R47N 0.1 0.01 0.001 0.1 1 10 Frequency(MHz) 100 1000 Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (20/53) I N D U C T O R S VLS-E-CA series VLS2012E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 220M 150M 10 100M Inductance(H) 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R68N R47N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (21/53) I N D U C T O R S VLS-E-CA series VLS252008E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.85) 0.8max. 2.50.1 (0.8) (0.85) Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.85 0.8 0.85 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (22/53) I N D U C T O R S VLS-E-CA series VLS252008E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10.0 Tolerance 30% 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.140 0.116 0.219 0.182 0.248 0.206 0.290 0.241 0.416 0.346 0.580 0.483 0.818 0.681 1.232 1.026 Rated current(A) max. typ. Idc1 Idc1 1.65 1.80 1.20 1.35 1.00 1.10 0.77 0.86 0.73 0.82 0.61 0.68 0.49 0.55 0.43 0.48 Part No. Idc2 1.20 0.97 0.91 0.84 0.70 0.59 0.50 0.41 VLS252008ET-R47N-CA VLS252008ET-1R0N-CA VLS252008ET-1R5N-CA VLS252008ET-2R2M-CA VLS252008ET-3R3M-CA VLS252008ET-4R7M-CA VLS252008ET-6R8M-CA VLS252008ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (23/53) I N D U C T O R S VLS-E-CA series VLS252008E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M 4R7M Inductance(H) 10 3R3M 2R2M 1R5N 1 1R0N R47N 0.1 0.1 1 10 Frequency(MHz) 100 1000 Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (24/53) I N D U C T O R S VLS-E-CA series VLS252008E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R47N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (25/53) I N D U C T O R S VLS-E-CA series VLS252010E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.85) 1.0max. 2.50.1 (0.8) (0.85) Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.85 0.8 0.85 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (26/53) I N D U C T O R S VLS-E-CA series VLS252010E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 Tolerance 30% 30% 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.046 0.038 0.062 0.052 0.084 0.070 0.128 0.107 0.190 0.158 0.275 0.229 0.398 0.332 0.532 0.443 0.854 0.712 Rated current(A) max. typ. Idc1 Idc1 2.50 2.80 2.05 2.30 1.75 1.90 1.45 1.60 1.20 1.30 0.94 1.05 0.80 0.89 0.68 0.76 0.56 0.63 Part No. Idc2 2.65 2.20 1.90 1.50 1.20 1.00 0.82 0.71 0.55 VLS252010ET-R47N-CA VLS252010ET-R68N-CA VLS252010ET-1R0N-CA VLS252010ET-1R5N-CA VLS252010ET-2R2M-CA VLS252010ET-3R3M-CA VLS252010ET-4R7M-CA VLS252010ET-6R8M-CA VLS252010ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (27/53) I N D U C T O R S VLS-E-CA series VLS252010E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M Inductance(H) 10 4R7M 3R3M 2R2M 1R5N 1R0N 1 R68N R47N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (28/53) I N D U C T O R S VLS-E-CA series VLS252010E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R68N 0.1 0 0.5 1 1.5 DC current(A) 2 2.5 R47N 3 Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (29/53) I N D U C T O R S VLS-E-CA series VLS252012E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.85) 1.2max. 2.50.1 (0.8) (0.85) Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.85 0.8 0.85 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (30/53) I N D U C T O R S VLS-E-CA series VLS252012E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 0.47 1.0 1.5 2.2 3.3 4.7 6.8 10 Tolerance 30% 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.056 0.047 0.087 0.073 0.126 0.105 0.154 0.129 0.272 0.227 0.405 0.338 0.612 0.510 0.756 0.630 Rated current(A) max. typ. Idc1 Idc1 2.75 3.10 2.20 2.45 1.80 2.00 1.55 1.75 1.25 1.40 1.05 1.20 0.85 0.95 0.73 0.82 Part No. Idc2 2.15 1.70 1.45 1.30 0.98 0.81 0.65 0.59 VLS252012ET-R47N-CA VLS252012ET-1R0N-CA VLS252012ET-1R5N-CA VLS252012ET-2R2M-CA VLS252012ET-3R3M-CA VLS252012ET-4R7M-CA VLS252012ET-6R8M-CA VLS252012ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (31/53) I N D U C T O R S VLS-E-CA series VLS252012E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M 4R7M Inductance(H) 10 3R3M 2R2M 1R5N 1R0N 1 R47N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (32/53) I N D U C T O R S VLS-E-CA series VLS252012E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N R47N 0.1 0 0.5 1 1.5 2 DC current(A) 2.5 3 3.5 4 Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (33/53) I N D U C T O R S VLS-E-CA series VLS252015E-CA Type 2.00.1 SHAPE & DIMENSIONS (0.85) 1.5max. 2.50.1 (0.8) (0.85) Dimensions in mm 2.0 RECOMMENDED LAND PATTERN 0.85 0.8 0.85 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (34/53) I N D U C T O R S VLS-E-CA series VLS252015E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 1.0 1.5 2.2 3.3 4.7 6.8 10 Tolerance 30% 30% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.082 0.068 0.120 0.100 0.160 0.133 0.219 0.182 0.318 0.265 0.480 0.400 0.588 0.490 Rated current(A) max. typ. Idc1 Idc1 1.95 2.20 1.75 1.95 1.50 1.70 1.20 1.35 1.00 1.15 0.85 0.95 0.72 0.80 Part No. Idc2 1.75 1.45 1.25 1.05 0.89 0.73 0.66 VLS252015ET-1R0N-CA VLS252015ET-1R5N-CA VLS252015ET-2R2M-CA VLS252015ET-3R3M-CA VLS252015ET-4R7M-CA VLS252015ET-6R8M-CA VLS252015ET-100M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (35/53) I N D U C T O R S VLS-E-CA series VLS252015E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 100M 6R8M 4R7M 3R3M 2R2M Inductance(H) 10 1R5N 1R0N 1 0.1 0.01 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (36/53) I N D U C T O R S VLS-E-CA series VLS252015E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (37/53) I N D U C T O R S VLS-E-CA series VLS3010E-CA Type 3.00.1 SHAPE & DIMENSIONS (0.9) (1.2) (0.9) 1.0max. 3.00.1 Dimensions in mm 3.0 RECOMMENDED LAND PATTERN 1.0 1.0 1.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (38/53) I N D U C T O R S VLS-E-CA series VLS3010E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 Tolerance 30% 30% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.072 0.060 0.085 0.071 0.116 0.097 0.156 0.130 0.204 0.170 0.312 0.260 0.468 0.390 0.612 0.510 0.900 0.750 Rated current(A) max. typ. Idc1 Idc1 1.60 1.80 1.35 1.50 1.20 1.30 1.00 1.10 0.81 0.90 0.69 0.77 0.56 0.63 0.48 0.54 0.38 0.43 Part No. Idc2 2.10 1.90 1.70 1.50 1.30 1.00 0.80 0.70 0.60 VLS3010ET-1R0N-CA VLS3010ET-1R5N-CA VLS3010ET-2R2M-CA VLS3010ET-3R3M-CA VLS3010ET-4R7M-CA VLS3010ET-6R8M-CA VLS3010ET-100M-CA VLS3010ET-150M-CA VLS3010ET-220M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (39/53) I N D U C T O R S VLS-E-CA series VLS3010E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 220M 150M 100M 6R8M Inductance(H) 10 4R7M 3R3M 2R2M 1R5N 1 0.1 0.01 1R0N 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (40/53) I N D U C T O R S VLS-E-CA series VLS3010E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 220M 150M Inductance(H) 10 100M 6R8M 4R7M 3R3M 2R2M 1 1R5N 1R0N 0.1 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (41/53) I N D U C T O R S VLS-E-CA series VLS3012E-CA Type 3.00.1 SHAPE & DIMENSIONS (0.9) (1.2) (0.9) 1.2max. 3.00.1 Dimensions in mm 3.0 RECOMMENDED LAND PATTERN 1.0 1.0 1.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (42/53) I N D U C T O R S VLS-E-CA series VLS3012E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Tolerance 30% 30% 20% 20% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.068 0.056 0.076 0.063 0.096 0.080 0.120 0.100 0.156 0.130 0.228 0.190 0.336 0.280 0.516 0.430 0.756 0.630 1.248 1.040 1.500 1.250 Rated current(A) max. typ. Idc1 Idc1 1.90 2.15 1.50 1.70 1.35 1.50 1.05 1.20 0.95 1.05 0.81 0.90 0.64 0.76 0.55 0.62 0.44 0.49 0.37 0.41 0.31 0.35 Part No. Idc2 2.00 1.85 1.70 1.55 1.30 1.05 0.89 0.74 0.61 0.48 0.44 VLS3012ET-1R0N-CA VLS3012ET-1R5N-CA VLS3012ET-2R2M-CA VLS3012ET-3R3M-CA VLS3012ET-4R7M-CA VLS3012ET-6R8M-CA VLS3012ET-100M-CA VLS3012ET-150M-CA VLS3012ET-220M-CA VLS3012ET-330M-CA VLS3012ET-470M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (43/53) I N D U C T O R S VLS-E-CA series VLS3012E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 1000 100 470M 330M Inductance(H) 220M 150M 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (44/53) I N D U C T O R S VLS-E-CA series VLS3012E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 470M 330M 220M 150M 10 100M Inductance(H) 6R8M 4R7M 3R3M 2R2M 1R5N 1 0.1 1R0N 0 0.5 1 1.5 DC current(A) 2 2.5 3 Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (45/53) I N D U C T O R S VLS-E-CA series VLS3015E-CA Type 3.00.1 SHAPE & DIMENSIONS (0.9) 1.5max. 3.00.1 (1.2) (0.9) Dimensions in mm 3.0 RECOMMENDED LAND PATTERN 1.0 1.0 1.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (46/53) I N D U C T O R S VLS-E-CA series VLS3015E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Tolerance 30% 30% 20% 20% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.058 0.048 0.075 0.062 0.084 0.070 0.112 0.093 0.136 0.113 0.216 0.180 0.288 0.240 0.456 0.380 0.660 0.550 0.984 0.820 1.500 1.250 Rated current(A) max. typ. Idc1 Idc1 2.00 2.20 1.50 1.70 1.35 1.50 1.15 1.30 1.00 1.10 0.92 1.00 0.70 0.78 0.58 0.65 0.48 0.54 0.39 0.43 0.32 0.35 Part No. Idc2 2.10 1.85 1.75 1.50 1.35 1.05 0.94 0.75 0.62 0.51 0.41 VLS3015ET-1R0N-CA VLS3015ET-1R5N-CA VLS3015ET-2R2M-CA VLS3015ET-3R3M-CA VLS3015ET-4R7M-CA VLS3015ET-6R8M-CA VLS3015ET-100M-CA VLS3015ET-150M-CA VLS3015ET-220M-CA VLS3015ET-330M-CA VLS3015ET-470M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (47/53) I N D U C T O R S VLS-E-CA series VLS3015E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 1000 100 470M 330M Inductance(H) 220M 150M 100M 10 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (48/53) I N D U C T O R S VLS-E-CA series VLS3015E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 470M 330M 220M 150M 10 100M Inductance(H) 6R8M 4R7M 3R3M 2R2M 1R5N 1 0.1 1R0N 0 0.5 1 1.5 2 2.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (49/53) I N D U C T O R S VLS-E-CA series VLS4012E-CA Type 4.00.1 SHAPE & DIMENSIONS (1.3) (1.4) (1.3) 1.2max. 4.00.1 Dimensions in mm 4.0 RECOMMENDED LAND PATTERN 1.3 1.4 1.3 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (50/53) I N D U C T O R S VLS-E-CA series VLS4012E-CA Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (H) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 Tolerance 30% 30% 20% 20% 20% 20% 20% 20% 20% 20% 20% Measuring frequency (MHz) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 DC resistance ( ) max. typ. 0.060 0.050 0.072 0.060 0.081 0.067 0.102 0.085 0.118 0.098 0.156 0.130 0.228 0.190 0.372 0.310 0.468 0.390 0.804 0.670 1.020 0.850 Rated current(A) max. typ. Idc1 Idc1 2.50 2.80 2.10 2.30 1.70 1.90 1.40 1.60 1.20 1.40 1.00 1.20 0.89 0.99 0.70 0.78 0.63 0.70 0.47 0.53 0.41 0.46 Part No. Idc2 2.65 2.45 2.20 2.00 1.90 1.60 1.33 1.05 0.95 0.70 0.61 VLS4012ET-1R0N-CA VLS4012ET-1R5N-CA VLS4012ET-2R2M-CA VLS4012ET-3R3M-CA VLS4012ET-4R7M-CA VLS4012ET-6R8M-CA VLS4012ET-100M-CA VLS4012ET-150M-CA VLS4012ET-220M-CA VLS4012ET-330M-CA VLS4012ET-470M-CA Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40C by self heating) Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (51/53) I N D U C T O R S VLS-E-CA series VLS4012E-CA Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 1000 100 470M Inductance(H) 330M 220M 150M 10 100M 6R8M 4R7M 3R3M 2R2M 1R5N 1 1R0N 0.1 0.01 0.1 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer 4294A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (52/53) I N D U C T O R S VLS-E-CA series VLS4012E-CA Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 100 470M 330M 220M 150M 10 100M Inductance(H) 6R8M 4R7M 3R3M 2R2M 1R5N 1 0.1 1R0N 0 0.5 1 1.5 2 2.5 3 3.5 DC current(A) Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm (53/53) I N D U C T O R S VLS-E-CA series Packaging Style REEL DIMENSIONS E Type VLS201610E-CA VLS201612E-CA VLS2010E-CA VLS2012E-CA VLS252008E-CA VLS252010E-CA VLS252012E-CA VLS252015E-CA VLS3010E-CA VLS3012E-CA VLS3015E-CA VLS4012E-CA N 2.00.5 (1.0) o13.00.5 A o180 o180 o180 o180 o180 o180 o180 o180 o180 o180 o180 o180 W1 9 9 9 9 9 9 9 9 9 9 9 13 W2 13 13 13 13 13 13 13 13 13 13 13 17 N o60 o60 o60 o60 o60 o60 o60 o60 o60 o60 o60 o60 E 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 W1 * These values are typical values. o21.00.8 W2 A Dimensions in mm TAPE DIMENSIONS P2 P0 K P1 t A Type VLS201610E-CA VLS201612E-CA VLS2010E-CA VLS2012E-CA VLS252008E-CA VLS252010E-CA VLS252012E-CA VLS252015E-CA VLS3010E-CA VLS3012E-CA VLS3015E-CA VLS4012E-CA A 1.8 1.8 2.2 2.2 2.15 2.15 2.15 2.15 3.2 3.2 3.2 4.25 B 2.2 2.2 2.2 2.2 2.7 2.7 2.7 2.7 3.2 3.2 3.2 4.25 B W F E oD0 oD0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 1.5+0.10/-0 E 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 1.750.1 F 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 3.50.05 5.50.05 Dimensions in mm P0 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 P1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 4.00.1 8.00.1 P2 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 2.000.05 W 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 8.00.2 12.00.2 K 1.1 1.3 1.1 1.35 0.95 1.15 1.35 1.65 1.15 1.35 1.65 1.35 t 0.25 0.25 0.25 0.25 0.25 0.3 0.3 0.3 0.25 0.25 0.25 0.3 * All specifications are subject to change without notice. 001-01 / 20140210 / inductor_automotive_power_vls-e-ca_en.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: VLS3015ET-4R7M-CA VLS4012ET-6R8M-CA VLS2010ET-2R2M-CA VLS2012ET-2R2M-CA VLS3010ET-3R3M-CA VLS252008ET-1R5N-CA VLS2012ET-3R3M-CA VLS252010ET-100M-CA VLS4012ET-2R2M-CA VLS2012ET4R7M-CA VLS252008ET-3R3M-CA VLS3010ET-1R0N-CA VLS3010ET-150M-CA VLS252008ET-4R7M-CA VLS4012ET-1R5N-CA VLS4012ET-150M-CA VLS3015ET-330M-CA VLS201610ET-2R2M-CA VLS201612ET-2R2MCA VLS3015ET-1R0N-CA VLS2010ET-150M-CA VLS4012ET-220M-CA VLS3010ET-4R7M-CA VLS3012ET-4R7MCA VLS3015ET-100M-CA VLS3015ET-220M-CA VLS3012ET-1R0N-CA VLS201610ET-100M-CA VLS2012ET1R5N-CA VLS201612ET-100M-CA VLS252010ET-R68N-CA VLS3012ET-6R8M-CA VLS252008ET-1R0N-CA VLS3010ET-6R8M-CA VLS4012ET-4R7M-CA VLS3015ET-150M-CA VLS3012ET-220M-CA VLS2012ET-220M-CA VLS3010ET-1R5N-CA VLS3010ET-220M-CA VLS3010ET-100M-CA VLS3015ET-2R2M-CA VLS3012ET-3R3M-CA VLS4012ET-3R3M-CA VLS3012ET-470M-CA VLS2010ET-100M-CA VLS3015ET-6R8M-CA VLS2012ET-R47N-CA VLS3012ET-330M-CA VLS252008ET-R47N-CA VLS252010ET-2R2M-CA VLS2010ET-1R5N-CA VLS2010ET-6R8MCA VLS252008ET-100M-CA VLS252008ET-2R2M-CA VLS2012ET-100M-CA VLS2010ET-4R7M-CA VLS3015ET3R3M-CA VLS2012ET-R68N-CA VLS3012ET-1R5N-CA VLS2010ET-1R0N-CA VLS3012ET-100M-CA VLS4012ET330M-CA VLS2010ET-R56N-CA VLS3012ET-2R2M-CA VLS4012ET-470M-CA VLS4012ET-1R0N-CA VLS4012ET100M-CA VLS252015ET-100M-CA VLS2012ET-1R0N-CA VLS3010ET-2R2M-CA VLS252008ET-6R8M-CA VLS3015ET-470M-CA VLS2010ET-3R3M-CA VLS3015ET-1R5N-CA VLS2012ET-150M-CA VLS252012ET-100M-CA VLS3012ET-150M-CA VLS2012ET-6R8M-CA VLS2010ET-220M-CA VLS201612ET-R68N-CA VLS252015ET6R8M-CA VLS201612ET-3R3M-CA VLS201612ET-6R8M-CA VLS201612ET-1R0N-CA VLS201612ET-1R5N-CA VLS201612ET-4R7M-CA VLS252015ET-1R0N-CA VLS252015ET-1R5N-CA VLS252015ET-3R3M-CA VLS201612ET-R47N-CA VLS252015ET-2R2M-CA VLS252015ET-4R7M-CA