POWER
LGA80D Series
Dual O/P Non-isolated 80 A Digital DC/DC Converter
Total Current: 80 A (single)
40 A (dual)
Input Voltage: 7.5 - 14 Vdc
Variable Output: 0.6 - 5.2 V
SPECIAL FEATURES
Two-phase design
Dual or single output conguration
possible
High efciency up to 95.5%
Small size 1” x 0.5” x 0.48” (LxWxH)
Supports PMBus
No minimum load requirement
Wide operating temperature range
Exceptional power density
Automatic loop compensation
Excellent transient response
Analog or digital control
IPC9592B compliant
Tape and reel packaging
Reow compatible
Possible to stack up to 8 phases for
320 A
Two year warranty (Consult factory
for extended terms)
SAFETY
Designed to meet EN60950-1
Electrical Specications
Input
Input voltage range 7.5 -14 Vdc
Max input current @ 7.5 V 33 A
Input capacitor (internal) 120 µF
Environmental and General Information
Operating ambient temperature -40 °C to +85 °C
Storage temperature -40 °C to +125 °C
Switching frequency (RSYNC = 23.7 Kohm) 457 kHz typical (can be congured)
CMTBF Telcordia SR-332, Issue 3, Method 1 Case 1 50 MHours
Protection
Overcurrent protection Refer to application note for detail
Overvoltage protection 110% Vo nominal
Overtemperature protection (controller temperature) 120 °C nominal
Output*
Independent output 1 and 2 0.6 V to 1 V
1.8 V
2.5 V
3.3 V
5 V
40 A
35 A
32.5 A
30 A
20 A
Combined output 1 and 2 0.6 V to 1 V
1.8 V
2.5 V
3.3 V
5 V
80 A
70 A
65 A
60 A
40 A
Efciency at 11 Vin and 25 °C 1 V @ 80 A
1.8 V @ 70 A
2.5 V @ 65 A
3.3 V @ 60 A
5 V @ 40 A
89.9% typical
93% typical
94.5% typical
95% typical
95.5% typical
Max output power (Watts) 200 W
*Output @ Vin = 12 V, Ta = 25 °C, unless otherwise noted
Data Sheet
LGA80D Series Data Sheet
Ordering Information
Model Number Input Voltage Output Voltage Set Point Output Current Efficiency
LGA80D-00DADJJ 7.5 - 14 Vdc See table 80 A max See table
Electrical Specications (continued)
Parameter Conditions Min Nom Max
Line regulation
0.6 ~ 1.0 V
1.0 ~ 5.0 V
Measured at remote sense
—
2 mV
0.2%
—
Load regulation
0.6 ~ 1.0 V
1.0 ~ 5.0 V
Measured at remote sense
—
5 mV
0.5%
—
Output capacitor per output
(external minimum)
2 x 220 µF / 6.3 V polymer tan caps
(6TPF220M5L or equivalent
3 x 100 µF / 6.3 V ceramic caps
— 740 µF —
Ripple and noise
(with minimum caps) 5 Hz to 20 MHz
0.6 to 1.8 V
2.5 V to 3.3 V
5.0 V
One module one output
—
—
—
15 mV
25 mV
40 mV
—
—
—
Ripple and noise
(with minimum caps) 5 Hz to 20 MHz
0.6 to 1.8 V
2.5 V to 3.3 V
5.0 V
One module two outputs
—
—
—
18 mV
35 mV
50 mV
—
—
—
Block Diagram - One Module One Output
LGA80D Series Data Sheet
Block Diagram - One Module Two Outputs
Block Diagram - Two Modules One Output
LGA80D Series Data Sheet
Vout & Address Settings
Vout Setting
RVtrim (kΩ) Vout (V)
LOW 1
OPEN 1.2
HIGH 0.9
10 0.6
11 0.65
12.1 0.7
13.3 0.75
14.7 0.8
16.2 0.85
17.8 0.9
19.6 0.95
21.5 1
23.7 1.05
26.1 1.1
28.7 1.15
31.6 1.2
34.8 1.25
38.3 1.3
42.2 1.4
46.4 1.5
51.1 1.6
56.2 1.7
61.9 1.8
68.1 1.9
75 2
82.5 2.1
90.9 2.2
100 2.3
110 2.5
121 2.8
133 3
147 3.3
162 4
178 5
Address Setting
RADDR (kΩ) SMbus ADDRESS
LOW 40h
OPEN 42h
10 41h
11 43h
12.1 44h
13.3 45h
14.7 46h
16.2 47h
17.8 48h
19.6 49h
21.5 4Ah
23.7 4Bh
26.1 4Ch
28.7 4Dh
31.6 4Eh
34.8 4Fh
42.2 51h
46.4 52h
51.1 53h
56.2 54h
61.9 55h
68.1 56h
75 57h
82.5 58h
90.9 59h
100 5Ah
110 5Bh
121 5Ch
133 5Dh
147 5Eh
162 5Fh
178 60h
LGA80D Series Data Sheet
Mechanical Drawings
Pin Assignments
Single Output
Pin # Function
1 Vin
2 GND
3 PG1
4 PG2
5 EN1
6 EN2
7 SYNC
8 SHARE
9 ADDR
10 SCL
11 SDA
12 SALERT
13 SGND
14 ASCRCFG
15 CFG
16 Vtrim1
17 VS1+
18 VS1-
19 Vtrim2
20 VS2-
21 VS2+
22 Vo1
23 Vo1
24 GND
25 Vo2
26 Vo2
27 GND
28 Vin
RECOMMENDED PAD LAYOUT (FOOTPRINT)
Notes:
Dimensions are in millimeters and (inches)
Tolerance: X.X mm ±0.5 mm (X.XX in. ±0.02 in.)
X.XX mm ±0.25 mm (X.XXX in. ±0.010 in.)
12345678910 11 12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0.65 (2X)
3.50
6.15
7.95
9.75
11.55
13.35
15.15
16.95
18.75
20.55
22.35
0.35
3.25
6.50
9.75
13.00
15.65
17.40
19.15
20.90
22.65
21.50 (4X)
2.10 (9X)
2.90 (9X)
3.30
6.80
10.10
1.80
(19X)
1.10 (19X)
2.35
4.15
5.95
7.75
LGA80D Series Data Sheet
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
www.artesyn.com
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc.
All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal.
12345678910 11 12
13
14
15
16
1718
19
2021
22
23
24
25
26
27
28
2.30 (9X)
2.14
3.50
6.15
7.95
9.75
11.55
13.35
15.15
16.95
0.65 (2X)
1.60 (9X)
0.35
3.25
6.50
9.75
13.00
15.65
17.40
19.15
20.90
22.65
18.75
20.55
21.50 (4X)
22.35
1.50 (19X)
0.80 (19X)
3.30
1.30 (12X)
6.80
2.35
4.15
5.95
7.75
10.10 (10X)
LGA80D Series DS 22Nov2016
Mechanical Drawings
FOOTPRINT DRAWING OF METAL PINS
(BOTTOM VIEW)
Notes:
Dimensions are in millimeters and (inches)
Tolerance: X.X mm ±0.5 mm (X.XX in. ±0.02 in.)
X.XX mm ±0.25 mm (X.XXX in. ±0.010 in.)
TOP VIEW
SIDE VIEW
0.13
(0.005")
12.20 (0.48")
1.60 (0.063")