LMV751 LMV751 Low Noise, Low Vos, Single Op Amp Literature Number: SNOS468D LMV751 Low Noise, Low Vos, Single Op Amp General Description Features The LMV751 is a high performance CMOS operational amplifier intended for applications requiring low noise and low input offset voltage. It offers modest bandwidth of 4.5MHz for very low supply current and is unity gain stable. The output stage is able to drive high capacitance, up to 1000pF and source or sink 8mA output current. n n n n n n n n It is supplied in the space saving SOT23-5 Tiny package. The LMV751 is designed to meet the demands of small size, low power, and high performance required by cellular phones and similar battery operated portable electronics. Low noise 6.5nV/ Low VOS (0.05mV typ.) Wideband 4.5MHz GBP typ. Low supply current 500uA typ. Low supply voltage 2.7V to 5.0V Ground-referenced inputs Unity gain stable Small Package Applications n Cellular phones n Portable equipment n Radio systems Connection Diagram SOT23-5 10108101 Top View Ordering Information Package Part Number Package Marking Transport Media NSC Drawing 5-Pin SOT23-5 LMV751M5 A32A 1k Units Tape and Reel MA05B LMV751M5X Voltage Noise Gain/Phase 10108102 (c) 2002 National Semiconductor Corporation 3k units Tape and Reel DS101081 10108103 www.national.com LMV751 Low Noise, Low Vos, Single Op Amp July 2002 LMV751 Absolute Maximum Ratings Junction Temperature (TJ) (Note 4) (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Recommended Operating Conditions ESD Tolerance (Note 3) Human Body Model 2000V Machine Model 200V Differential Input Voltage + Supply Voltage - Supply Voltage (V - V ) 5.5V Lead Temperature (Soldering, 10 sec.) Storage Temperature Range 150C Supply Voltage 2.7V to 5.0V -40C TJ 85C Temperature Range Thermal Resistance (JA) (Note 6) M5 Package, SOT23-5 274C/W 260C -65C to 150C 2.7V Electrical Characteristics V+ = 2.7V, V- = 0V, VCM = 1.35V, TA = 25C unless otherwise stated. Boldface limits apply over the Temperature Range. Symbol Parameter VOS Input Offset Voltage VCM Input common-Mode Voltage Range Condition Typ (Note 5) Limit (Note 2) Units 0.05 1.0 1.5 mV max 0 V min 1.4 1.3 V max For CMRR 50dB CMRR Common Mode Rejection Ratio 0V < VCM < 1.3V 100 85 70 dB min PSRR Power Supply Rejection Ratio V+ = 2.7V to 5.0V 107 85 70 dB min IS Supply Current 0.5 0.8 0.85 mA max IIN Input Current 1.5 100 pA max IOS Input Offset Current AVOL Voltage Gain 0.2 RL = 10k Connect to V+/2 VO = 0.2V to 2.2V + VO VO IO Positive Voltage Swing Negative Voltage Swing Output Current 120 pA 110 95 RL = 2k Connect to V /2 VO = 0.2V to 2.2V 120 100 85 RL = 10k Connect to V+/2 2.62 2.54 2.52 RL = 2k Connect to V+/2 2.62 2.54 2.52 RL = 10k Connect to V+/2 78 140 160 RL = 2k Connect to V+/2 78 160 180 Sourcing, VO = 0V VIN (diff) = 0.5V 12 6.0 1.5 Sinking, VO = 2.7V VIN (diff) = 0.5V 11 6.0 1.5 dB min V min mV max mA min en (10Hz) Input Referred Voltage Noise 15.5 nV/ en (1kHz) Input Referred Voltage Noise 7 nV/ www.national.com 2 (Continued) V+ = 2.7V, V- = 0V, VCM = 1.35V, TA = 25C unless otherwise stated. Boldface limits apply over the Temperature Range. Symbol Parameter Condition Typ (Note 5) Limit (Note 2) 10 en (30kHz) Input Referred Voltage Noise 7 IN(1kHz) Input Referred Current Noise 0.01 GBW Gain-Bandwidth Product 4.5 SR Slew Rate Units nV/ max pA/ 2 2 MHZ min V/s 5.0V Electrical Characteristics V+ = 5.0V, V- = 0V, VCM = 2.5V, TA = 25C unless otherwise stated.Boldface limits apply over the Temperature Range. Symbol Parameter VOS Input Offset Voltage CMRR Common Mode Rejection Ratio 0V < VCM < 3.6V VCM Input Common-Mode Voltage Range For CMRR 50dB V+ = 2.7V to 5.0V Typ (Note 5) Limit (Note 2) Units 0.05 1.0 1.5 mV max 103 85 70 dB min 0 V min 3.7 3.6 V max 107 85 70 dB min PSRR Power Supply Rejection Ratio IS Supply Current 0.6 0.9 0.95 mA max IIN Input Current 1.5 100 pA max IOS Input offset Current AVOL Voltage Gain VO VO Positive Voltage Swing Negative Voltage Swing 0.2 120 110 95 RL = 2k Connect to V+/2 VO = 0.2V to 4.5V 120 100 85 RL = 10k Connect to V+/2 4.89 4.82 4.80 RL = 2k Connect to V+/2 4.89 4.82 4.80 RL = 10k Connect to V+/2 86 160 180 + IO Output Current pA RL = 10k Connect to V+/2 VO = 0.2V to 4.5V RL = 2k Connect to V /2 86 180 200 Sourcing, VO = 0V VIN (diff) = 0.5V 15 8.0 2.5 Sinking, VO = 5V VIN (diff) = 0.5V 20 8.0 2.5 db min V min mV max mA min en (10Hz) Input Referred Voltage Noise 15 nV/ en (1kHz) Input Referred Voltage Noise 6.5 nV/ 3 www.national.com LMV751 2.7V Electrical Characteristics LMV751 5.0V Electrical Characteristics (Continued) V+ = 5.0V, V- = 0V, VCM = 2.5V, TA = 25C unless otherwise stated.Boldface limits apply over the Temperature Range. Symbol Parameter Typ (Note 5) Limit (Note 2) 10 en (30kHz) Input Referred Voltage Noise 6.5 IN (1kHz) Input Referred Current Noise 0.01 GBW Gain-Bandwidth Product SR Slew Rate Units nV/ max 5 2.3 pA/ 2 MHz min V/s Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: All limits are guaranteed by testing or statistical analysis Note 3: Human body model, 1.5k in series with 100pF. Machine model, 200 in series with 1000pF. Note 4: The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/JA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical values represent the most likely parametric norm. Note 6: All numbers are typical, and apply to packages soldered directly onto PC board in still air. www.national.com 4 LMV751 Typical Performance Characteristics VOS vs. VCM, V+ = 2.7V Supply Current vs. Voltage 10108135 10108138 VOS vs. VCM, V+ = 5.0V Source Current vs. Out, V+ = 2.7V 10108137 10108128 + Source Current vs. VOUT, V = 5.0V Gain/Phase 10108103 10108129 5 www.national.com LMV751 Typical Performance Characteristics (Continued) Sinking Current vs. VOUT, V+ = 2.7V Sinking Current vs. VOUT, V+ = 5.0V 10108130 VOS vs. V 10108131 + + VIN vs. VOUT, V = 2.7V, RL = 2k 10108136 10108132 + VIN vs. VOUT, V = 5.0V, RL = 2k Input Bias vs. VCM, TA = 25C 10108116 10108133 www.national.com 6 LMV751 Typical Performance Characteristics (Continued) Input Bias vs. VCM, TA = 85C PSRR + 10108105 10108126 PSRR - Voltage Noise 10108125 10108102 CMRR 10108139 7 www.national.com LMV751 Application Hints 1.0 Noise 1.4 Resistor types There are many sources of noise in a system: thermal noise, shot noise, 1/f, popcorn noise, resistor noise, just to name a few. In addition to starting with a low noise op amp, such as the LMV751, careful attention to detail will result in the lowest overall noise for the system. Thermal noise is generated by any passive resistive element. This noise is 'white'; meaning it has a constant spectral density. Thermal noise can be represented by a meansquare voltage generator eR2 in series with a noiseless resistor, where eR2 is given by: Where: eR2 = 4K TRB (volts)2 Where T = temperature in K 1.1 To invert or not invert? Both inverting and non-inverting amplifiers employ feedback to stabilize the closed loop gain of the block being designed. The loop gain (in decibels) equals the algebraic difference between the open loop and closed loop gains. Feedback improves the Total Harmonic Distortion (THD) and the output impedance. The various noise sources, when input referred, are amplified, not by the closed loop gain, but by the noise gain. For a non-inverting amplifier, the noise gain is equal to the closed loop gain, but for an inverting amplifier, the noise gain is equal to the closed loop gain plus one. For large gains, e.g., 100, the difference is negligible, but for small gains, such as one, the noise gain for the inverting amplifier would be two. This implies that non-inverting blocks are preferred at low gains. R = resistor value in ohms B = noise bandwidth in Hz K = Boltzmann's constant (1.38 x 10-23 W-sec/K) Actual resistor noise measurements may have more noise than the calculated value. This additional noise component is known as excess noise. Excess noise has a 1/f spectral response, and is proportional to the voltage drop across the resistor. It is convenient to define a noise index when referring to excess noise in resistors. The noise index is the RMS value in uV of noise in the resistor per volt of DC drop across the resistor in a decade of frequency. Noise index expressed in dB is: NI = 20 log ((EEX/VDC) x 106) db Where: EEX = resistor excess noise in uV per frequency decade. VDC = DC voltage drop across the resistor. Excess noise in carbon composition resistors corresponds to a large noise index of +10 dB to -20 dB. Carbon film resistors have a noise index of -10 dB to -25 dB. Metal film and wire wound resistors show the least amount of excess noise, with a noise index figure of -15 dB to -40 dB. 1.5 Other noise sources: As the op amp and resistor noise sources are decreased, other noise contributors will now be noticeable. Small air currents across thermocouples will result in low frequency variations. Any two dissimilar metals, such as the lead on the IC and the solder and copper foil of the pc board, will form a thermocouple. The source itself may also generate noise. An example would be a resistive bridge. All resistive sources generate thermal noise based on the same equation listed above under 'resistor types'.(2) 1.6 Putting it all together To a first approximation, the total input referred noise of an op amp is: Et2 = en2 + ereq2 + (in*Req)2 where Req is the equivalent source resistance at the inputs. At low impedances, voltage noise dominates. At high impedances, current noise dominates. With a typical noise current , the current on most CMOS input op amps of 0.01 pA/ noise contribution will be smaller than the voltage noise for Req less than one megohm. 2.0 Other Considerations 2.1 Comparator operation Occasionally operational amplifiers are used as comparators. This is not optimum for the LMV751 for several reasons. First, the LMV751 is compensated for unity gain stability, so the speed will be less than could be obtained on the same process with a circuit specifically designed for comparator operation. Second, op amp output stages are designed to be linear, and will not necessarily meet the logic levels required under all conditions. Lastly, the LMV751 has the newer PNP-NPN common emitter output stage, characteristic of many rail-to-rail output op amps. This means that 1.2 Source impedance Because noise sources are uncorrelated, the system noise is calculated by taking the RMS sum of the various noise sources, that is, the square root of the sum of the squares. At very low source impedances, the voltage noise will dominate; at very high source impedances, the input noise current times the equivalent external resistance will dominate. For a detailed example calculation, refer to Note 1. 1.3 Bias current compensation resistor In CMOS input op amps, the input bias currents are very low, so there is no need to use RCOMP (Figure 1 and 2) for bias current compensation that would normally be used with early generation bipolar op amps. In fact, inclusion of the resistor would act as another thermal noise source in the system, increasing the overall noise. 10108123 FIGURE 1. 10108124 FIGURE 2. www.national.com 8 room from the positive rail. This is better than the industry standard LM324 and LM358 that have PNP input stages, and the LMV751 has the advantage of much lower input bias currents. (Continued) when used in open loop applications, such as comparators, with very light loads, the output PNP will saturate, with the output current being diverted into the previous stage. As a result, the supply current will increase to the 20-30 mA. range. When used as a comparator, a resistive load between 2k and 10k should be used with a small amount of hysteresis to alleviate this problem. When used as an op amp, the closed loop gain will drive the inverting input to within a few millivolts of the non-inverting input. This will automatically reduce the output drive as the output settles to the correct value; thus it is only when used as a comparator that the current will increase to the tens of milliampere range. 2.2 Rail-to-Rail 2.3 Loading The LMV751 is a low noise, high speed op amp with excellent phase margin and stability. Capacitive loads up to 1000 pF can be handled, but larger capacitive loads should be isolated from the output. The most straightforward way to do this is to put a resistor in series with the output. This resistor will also prevent excess power dissipation if the output is accidentally shorted. 2.4 General Circuits With the low noise and low input bias current, the LMV751 would be useful in active filters, integrators, current to voltage converters, low frequency sine wave generators, and instrumentation amplifiers. (3) Because of the output stage discussed above, the LMV751 will swing "rail-to-rail" on the output. This normally means within a few hundred millivolts of each rail with a reasonable load. Referring to the Electrical Characteristics table for 2.7V to 5.0V, it can be seen that this is true for resistive loads of 2k and 10k. The input stage consists of cascoded P-channel MOSFETS, so the input common mode range includes ground, but typically requires 1.2V to 1.3V head- Note: 1. Sherwin, Jim "Noise Specs Confusing?" AN-104, National Semiconductor. 2. Christensen, John, "Noise-figure curve ease the selection of low-noise op amps", EDN, pp 81-84, Aug. 4, 1994 3. "Op Amp Circuit Collection", AN-31, National Semiconductor. 9 www.national.com LMV751 Application Hints LMV751 Low Noise, Low Vos, Single Op Amp Physical Dimensions inches (millimeters) unless otherwise noted SOT23-5 NS Package Number MA05B LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated