© Semiconductor Components Industries, LLC, 1995
August, 2018 − Rev. 31 1Publication Order Number:
LP2950/D
LP2950, LP2951, NCV2951
100 mA, Low Power Low
Dropout Voltage Regulator
The LP2950 and LP2951 are micropower voltage regulators that are
specifically designed to maintain proper regulation with an extremely
low input−to−output voltage differential. These devices feature a very
low quiescent bias current of 75 mA and are capable of supplying
output currents in excess of 100 mA. Internal current and thermal
limiting protection is provided.
The LP2951 has three additional features. The first is the Error
Output that can be used to signal external circuitry of an out of
regulation condition, or as a microprocessor power−on reset. The
second feature allows the output voltage to be preset to 5.0 V, 3.3 V or
3.0 V output (depending on the version) or programmed from 1.25 V
to 29 V. It consists of a pinned out resistor divider along with direct
access to the Error Amplifier feedback input. The third feature is
a Shutdown input that allows a logic level signal to turn−of f or turn−on
the regulator output.
Due to the low input−to−output voltage differential and bias current
specifications, these devices are ideally suited for battery powered
computer , c onsumer, a nd industrial e quipment w here an extension of
useful battery life is desirable. The LP2950 is available in the three
pin case 29 and DPAK packages, and the LP2951 is available in the
eight p in dual−in−line, SOIC−8 and Micro8 surface mount p ackages.
The ‘A’ suffix devices feature an initial output voltage tolerance
±0.5%.
Features
Low Quiescent Bias Current of 75 mA
Low Input−to−Output Voltage Differential of 50 mV at 100 mA and
380 mV at 100 mA
5.0 V, 3.3 V or 3.0 V ±0.5% Allows Use as a Regulator or Reference
Extremely Tight Line and Load Regulation
Requires Only a 1.0 mF Output Capacitor for Stability
Internal Current and Thermal Limiting
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and RoHS Compliant
LP2951 Additional Features
Error Output Signals an Out of Regulation Condition
Output Programmable from 1.25 V to 29 V
Logic Level Shutdown Input
(See Following Page for Device Information.)
TO−92
CASE 29
See detailed ordering and shipping information in the package
dimensions section on pages 14 and 15 of this data sheet.
See general marking information in the device marking
section on page 17 of this data sheet.
ORDERING & MARKING INFORMATION
PIN CONNECTIONS
Pin: 1. Output
2. Ground
3. Input
DPAK
CASE 369C
Heatsink surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
123
(Top View)
Pin: 1. Input
2. Ground
3. Output
81
81
81
PIN CONNECTIONS
18
7
6
5
2
3
4
(Top View)
Output
Sense
Shutdown
Input
Feedback
Error Output
VO Tap
GND
SOIC−8
CASE 751
PDIP−8
CASE 626
Micro8E
CASE 846A
123
4
12312
BENT LEAD
TAPE & REEL
AMMO PACK
STRAIGHT LEAD
BULK PACK
3
www.onsemi.com
LP2950, LP2951, NCV2951
www.onsemi.com
2
DEVICE INFORMATION
Package
Output Voltage Operating Ambient
Temperature Range
3.0 V 3.3 V 5.0 V Adjustable
TO−92
Suffix Z LP2950CZ−3.0
LP2950ACZ−3.0 LP2950CZ−3.3
LP2950ACZ−3.3 LP2950CZ−5.0
LP2950ACZ−5.0 Not
Available TA = −40° to +125°C
DPAK
Suffix DT LP2950CDT−3.0
LP2950ACDT−3.0 LP2950CDT−3.3
LP2950ACDT−3.3 LP2950CDT−5.0
LP2950ACDT−5.0 Not
Available TA = −40° to +125°C
SOIC−8 NCV2951ACD−3.3R2 NCV2951ACDR2 NCV2951CDR2 TA = −40° to +125°C
SOIC−8
Suffix D LP2951CD−3.0
LP2951ACD−3.0 LP2951CD−3.3
LP2951ACD−3.3 LP2951CD
LP2951ACD LP2951CD
LP2951ACD TA = −40° to +125°C
Micro8
Suffix DM LP2951CDM−3.0
LP2951ACDM−3.0 LP2951CDM−3.3
LP2951ACDM−3.3 LP2951CDM
LP2951ACDM LP2951CDM
LP2951ACDM TA = −40° to +125°C
DIP−8
Suffix N LP2951CN−3.0
LP2951ACN−3.0 LP2951CN−3.3
LP2951ACN−3.3 LP2951CN
LP2951ACN LP2951CN
LP2951ACN TA = −40° to +125°C
LP2950Cx−xx / LP2951Cxx−xx 1% Output Voltage Precision at TA = 25°C
LP2950ACx−xx / LP2951ACxx−xx 0.5% Output Voltage Precision at TA = 25°C
From
CMOS/TTL
3
Figure 1. Representative Block Diagrams
This device contains 34 active transistors.
LP2950CZ−5.0
Battery or
Unregulated DC
GND 2
Output 5.0 V/100 mA
1
Input
3
1.23 V
Reference
Error Amplifier
182 k
60 k
1.0 mF
GND 4
182 k
60 k
1.23 V
Reference
1.0 mF
LP2951CD or CN
Error
Amplifier
Battery or
Unregulated DC
Shutdown
Error
Output
5
VO Tap
Feedback
6
7
Input 8 Output 1Sense 2 5.0 V/100 mA
330 k
To CMOS/TTL
75 mV/
60 mV
Error Detection
Comparator
50 k
60 k
LP2950, LP2951, NCV2951
www.onsemi.com
3
MAXIMUM RATINGS (TA = 25°C, unless otherwise noted.)
Rating Symbol Value Unit
Input Voltage VCC 30 Vdc
Peak Transient Input Voltage (t < 300 ms) VCC 32 Vdc
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Power Dissipation and Thermal Characteristics
ÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁ
Maximum Power Dissipation PDInternally Limited W
Case 751(SOIC−8) D Suffix
Thermal Resistance, Junction−to−Ambient RqJA 180 °C/W
Thermal Resistance, Junction−to−Case RqJC 45 °C/W
Case 369A (DPAK) DT Suffix (Note 1)
Thermal Resistance, Junction−to−Ambient RqJA 92 °C/W
Thermal Resistance, Junction−to−Case RqJC 6.0 °C/W
Case 29 (TO−226AA/TO−92) Z Suffix
Thermal Resistance, Junction−to−Ambient RqJA 160 °C/W
Thermal Resistance, Junction−to−Case RqJC 83 °C/W
Case 626 N Suffix
Thermal Resistance, Junction−to−Ambient RqJA 105 °C/W
Case 846A (Micro8) DM Suffix
Thermal Resistance, Junction−to−Ambient RqJA 240 °C/W
Feedback Input Voltage Vfb −1.5 to +30 Vdc
Shutdown Input Voltage Vsd −0.3 to +30 Vdc
Error Comparator Output Voltage Verr −0.3 to +30 Vdc
Operating Ambient Temperature Range TA−40 to +125 °C
Maximum Die Junction Temperature Range TJ+150 °C
Storage Temperature Range Tstg −65 to +150 °C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be af fected.
LP2950, LP2951, NCV2951
www.onsemi.com
4
ELECTRICAL CHARACTERISTICS
(Vin = VO + 1.0 V, IO = 100 mA, CO = 1.0 mF, TA = 25 °C [Note 3], unless otherwise noted.)
Characteristic Symbol Min Typ Max Unit
Output Voltage, 5.0 V Versions VOV
Vin = 6.0 V, IO = 100 mA, TA = 25°C
LP2950C−5.0/LP2951C/NCV2951C* 4.950 5.000 5.050
LP2950AC−5.0/LP2951AC/NCV2951AC* 4.975 5.000 5.025
TA = −40 to +125°C
LP2950C−5.0/LP2951C/NCV2951C* 4.900 5.100
LP2950AC−5.0/LP2951AC/NCV2951AC* 4.940 5.060
Vin = 6.0 to 30 V, IO = 100 mA to 100 mA, TA = −40 to +125°C
LP2950C−5.0/LP2951C/NCV2951C* 4.880 5.120
LP2950AC−5.0/LP2951AC/NCV2951AC* 4.925 5.075
Output Voltage, 3.3 V Versions VOV
Vin = 4.3 V, IO = 100 mA, TA = 25°C
LP2950C−3.3/LP2951C−3.3 3.267 3.300 3.333
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3* 3.284 3.300 3.317
TA = −40 to +125°C
LP2950C−3.3/LP2951C−3.3 3.234 3.366
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3* 3.260 3.340
Vin = 4.3 to 30 V, IO = 100 mA to 100 mA, TA = −40 to +125°C
LP2950C−3.3/LP2951C−3.3 3.221 3.379
LP2950AC−3.3/LP2951AC−3.3/NCV2951AC−3.3* 3.254 3.346
Output Voltage, 3.0 V Versions VOV
Vin = 4.0 V, IO = 100 mA, TA = 25°C
LP2950C−3.0/LP2951C−3.0 2.970 3.000 3.030
LP2950AC−3.0/LP2951AC−3.0 2.985 3.000 3.015
TA = −40 to +125°C
LP2950C−3.0/LP2951C−3.0 2.940 3.060
LP2950AC−3.0/LP2951AC−3.0 2.964 3.036
Vin = 4.0 to 30 V, IO = 100 mA to 100 mA, TA = −40 to +125°C
LP2950C−3.0/LP2951C−3.0 2.928 3.072
LP2950AC−3.0/LP2951AC−3.0 2.958 3.042
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. The Junction−to−Ambient Thermal Resistance is determined by PCB copper area per Figure 29.
2. This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM), 2000 V, Class 2, JESD22 A114−C
Machine Model (MM), 200 V, Class B, JESD22 A115 A
Charged Device Model (CDM), 2000 V, Class IV, JESD22 C101−C
3. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
4. VO(nom) is the part number voltage option.
5. Noise tests on the LP2951 are made with a 0.01 mF capacitor connected across Pins 7 and 1.
6. Latch−up Current Maximum Rating tested per JEDEC standard: JESD78
− Inputs Low: passing positive current 100 mA and negative current −100 mA
− Inputs High: passing positive current 100 mA and negative current −10 mA.
*NCV prefix is for automotive and other applications requiring site and change control.
LP2950, LP2951, NCV2951
www.onsemi.com
5
ELECTRICAL CHARACTERISTICS (continued)
(Vin = VO + 1.0 V, IO = 100 mA, CO = 1.0 mF, TA = 25 °C [Note 9], unless otherwise noted.)
Characteristic Symbol Min Typ Max Unit
Line Regulation (Vin = VO(nom) +1.0 V to 30 V) (Note 10) Regline %
LP2950C−XX/LP2951C/LP2951C−XX/NCV2951C* 0.08 0.20
LP2950AC−XX/LP2951AC/LP2951AC−XX/NCV2951AC* 0.04 0.10
Load Regulation (IO = 100 mA to 100 mA) Regload %
LP2950C−XX/LP2951C/LP2951C−XX/NCV2951C* 0.13 0.20
LP2950AC−XX/LP2951AC/LP2951AC−XX/NCV2951AC* 0.05 0.10
Dropout Voltage VI − VOmV
IO = 100 mA 30 80
IO = 100 mA 350 450
Supply Bias Current ICC
IO = 100 mA 93 120 mA
IO = 100 mA 4.0 12 mA
Dropout Supply Bias Current (Vin = VO(nom) − 0.5 V,
IO = 100 mA) (Note 10) ICCdropout 110 170 mA
Current Limit (VO Shorted to Ground) ILimit 220 300 mA
Thermal Regulation Regthermal 0.05 0.20 %/W
Output Noise Voltage (10 Hz to 100 kHz) (Note 11) VnmVrms
CL = 1.0 mF 126
CL = 100 mF 56
LP2951A/LP2951AC Only
Reference Voltage (TA = 25°C) Vref V
LP2951C/LP2951C−XX/NCV2951C* 1.210 1.235 1.260
LP2951AC/LP2951AC−XX/NCV2951AC* 1.220 1.235 1.250
Reference Voltage (TA = −40 to +125°C) Vref V
LP2951C/LP2951C−XX/NCV2951C* 1.200 1.270
LP2951AC/LP2951AC−XX/NCV2951AC* 1.200 1.260
Reference Voltage (TA = −40 to +125°C) Vref V
IO = 100 mA to 100 mA, Vin = 23 to 30 V
LP2951C/LP2951C−XX/NCV2951C* 1.185 1.285
LP2951AC/LP2951AC−XX/NCV2951AC* 1.190 1.270
Feedback Pin Bias Current IFB 15 40 nA
Error Comparator
Output Leakage Current (VOH = 30 V) Ilkg 0.01 1.0 mA
Output Low Voltage (Vin = 4.5 V, IOL = 400 mA) VOL 150 250 mV
Upper Threshold Voltage (Vin = 6.0 V) Vthu 40 45 mV
Lower Threshold Voltage (Vin = 6.0 V) Vthl 60 95 mV
Hysteresis (Vin = 6.0 V) Vhy 15 mV
Shutdown Input
Input Logic Voltage Vshtdn V
Logic “0” (Regulator “On”) 0 0.7
Logic “1” (Regulator “Off”) 2.0 30
Shutdown Pin Input Current Ishtdn mA
Vshtdn = 2.4 V 35 50
Vshtdn = 30 V 450 600
Regulator Output Current in Shutdown Mode Ioff 3.0 10 mA
(Vin = 30 V, Vshtdn = 2.0 V, VO = 0, Pin 6 Connected to Pin 7)
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
7. The Junction−to−Ambient Thermal Resistance is determined by PCB copper area per Figure 29.
8. ESD data available upon request.
9. Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible.
10.VO(nom) is the part number voltage option.
11.Noise tests on the LP2951 are made with a 0.01 mF capacitor connected across Pins 7 and 1.
*NCV prefix is for automotive and other applications requiring site and change control.
LP2950, LP2951, NCV2951
www.onsemi.com
6
DEFINITIONS
Dropout Voltage − The input/output voltage dif ferential
at which the regulator output no longer maintains regulation
against further reductions in input voltage. Measured when
the output drops 100 mV below its nominal value (which is
measured at 1.0 V differential), dropout voltage is affected
by junction temperature, load current and minimum input
supply requirements.
Line Regulation − The change in output voltage for a
change in input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that average chip temperature is not significantly
affected.
Load Regulation − The change in output voltage for a
change in load current at constant chip temperature.
Maximum Power Dissipation − The maximum total
device dissipation for which the regulator will operate
within specifications.
Bias Current − Current which is used to operate the
regulator chip and is not delivered to the load.
Output Noise Voltage − The RMS ac voltage at the
output, with constant load and no input ripple, measured
over a specified frequency range.
Leakage Current − Current drawn through a bipolar
transistor collector−base junction, under a specified
collector voltage, when the transistor is “off”.
Upper Threshold Voltage Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “0” to “1”.
Lower Threshold Voltage Voltage applied to the
comparator input terminal, below the reference voltage
which is applied to the other comparator input terminal,
which causes the comparator output to change state from a
logic “1” to “0”.
Hysteresis The difference between Lower Threshold
voltage and Upper Threshold voltage.
25°C
Figure 2. Quiescent Current
, OUTPUT VOLTAGE (V)
Vout
, OUTPUT VOLTAGE (V)
Vout
-50
5.00
0
6.0
0.1
10
TA, AMBIENT TEMPERATURE (°C)
Vin, INPUT VOLTAGE (V)
LP2950/LP2951 BIAS CURRENT (mA)
IL, LOAD CURRENT (mA)
Figure 3. 5.0 V Dropout Characteristics over
Load
Figure 4. Output Voltage versus Temperature
1.0 10 100 1.0 2.0 3.0 4.0 5.0 6.0
0 50 100 150
1.0
0.1
0.01
5.0
4.0
3.0
2.0
1.0
0
4.99
4.98
4.97
4.96
4.95
RL = 50 kW
RL = 50 W
LP2951C
TA = 25°C
LP2951C
200
, OUTPUT VOLTAGE (V)
Vout
0
6.0
Vin, INPUT VOLTAGE (V)
Figure 5. 5.0 V Dropout Characteristics with
RL = 50 W
1.0 2.0 3.0 4.0
5.0
3.0
2.0
1.0
0
6.05.0
4.0
125°C−40°C
LP2951C
LP2950, LP2951, NCV2951
www.onsemi.com
7
RL
DROPOUT VOLTAGE (mV) = 50
T, TEMPERATURE (°C)
0
8.0
-50
550
-100
4.70
5.0
0.1
400
, INPUT VOLTAGE (V)
t, TIME (ms)
SHUTDOWN AND OUTPUT VOLTAGE (V)
t, TIME (ms)
, OUTPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
DROPOUT VOLTAGE (mV)
IO, OUTPUT CURRENT (mA)
1.0 10 100
0 50 100 150 4.74 4.78 4.82 4.86
100 200 300
4.9
0
400 500 600 700 800 0 100 200 300 400
300
200
0
500
450
400
300
7.5
7.0
6.5
6.0
5.5
4.0
3.0
1.0
0
5.0
3.0
1.0
-1.0
RL = 50
Vin Decreasing
Vin Increasing
Vin
Vout
RL = 50 k
TA = 25°C
CL = 1.0 mF
IL = 1.0 mA
VO = 5.0 V
TA = 25°C
IL = 10 mA
Vin = 8.0 V
Vout = 5.0 V
CL = 10 mF
Shutdown Input
350
RL
DROPOUT VOLTAGE (mV) = 50 k
55
50
45
40
30
35
350
250
150
100
2.0
OUTPUT VOLTAGE CHANGE (mV)
4.0
2.0
0
-2.0
-6.0
-4.0
6.0
4.0
2.0
0
50
Vin
Vout
CL = 1.0 mF
TA = 25°C
LP2951C
RL = 330 k
TA = 25°C
0
250
BIAS CURRENT ( A)μ
Vin, INPUT VOLTAGE (V)
Figure 6. Input Current
5.0 10 15 20 25
200
150
100
50
0
0.1 mA Load Current
No Load
Figure 7. Dropout Voltage versus Output Curren
t
Figure 8. Dropout Voltage versus Temperature Figure 9. Error Comparator Output
Figure 10. Line Transient Response Figure 11. LP2951 Enable Transient
LP2950, LP2951, NCV2951
www.onsemi.com
8
1
0
100
100
4.0
-40
1.8
1.0
80
V
out, OUTPUT CURRENT (mA)
Vin, INPUT VOLTAGE (V)
VOLTAGE NOISE ( V/ Hz)
f, FREQUENCY (Hz)
SHUTDOWN THRESHOLD VOLTAGE (V)
t, TEMPERATURE (°C)
RIPPLE REJECTION (dB)
f, FREQUENCY (Hz)
TA = 25°C
CL = 1.0 mF
Vin = 6.0 V
Vout = 5.0 V
CL = 1.0 mF
μ
CL = 100 mF
IL= 0.1 mA
IL= 100 mA
TA = 25°C
VO = 5.0 V
LP2951C
Output “Off"
Output “On"
TA = 25°C
LP2951CN
60
40
20
0
3.0
2.0
1.0
0
80
60
40
20
0
1.4
1.0
0.8
1.2
1.6
10 100 1.0 k 10 k 100 k
1.0 k 10 k 100 k -20 40 80 120 160
5.0 15 25 35 4010 20 30
60 100 140200
TA = 75°C
4.0
2.0
0
-2.0
-4.0
-6.0
OUTPUT VOLTAGE CHANGE (mV)
0.01
0.1
10
100
1000
10000
0 102030405060708090100
Output Current (mA)
ESR (ohms)
Unstable Region
Stable Region
Unstable Region for 0.1 mF capacitor only
100 mF
0.1 mF
Vout = 5 V
Lower unstable region is for 0.1 mF only.
1 mF and 100 mF show no instability with low ESR values.
0
200
LOAD CURRENT (mA)
t, TIME (ms)
Figure 12. Load Transient Response
42.50.5 1.5 2 3 3.51
150
100
0
-50
50
Vout
ILoad
OUTPUT VOLTAGE CHANGE (mV)
0
-200
200
400
-400
CL = 1.0 mF
Vout = 5.0 V
IL = 400 mA to 75 mA
TA = 25°C
Figure 13. Ripple Rejection
Figure 14. Output Noise Figure 15. Shutdown Threshold Voltage
versus Temperature
Figure 16. Maximum Rated
Output Current Figure 17. Output Stability versus Output Capacito
r
Change
LP2950, LP2951, NCV2951
www.onsemi.com
9
APPLICATIONS INFORMATION
Introduction
The LP2950/LP2951 regulators are designed with
internal current limiting and thermal shutdown making them
user−friendly. Typical application circuits for the LP2950
and LP2951 are shown in Figures 20 through 28.
These regulators are not internally compensated and thus
require a 1.0 mF (or greater) capacitance between the
LP2950/LP2951 output terminal and ground for stability.
Most types of aluminum, tantalum or multilayer ceramic
will perform adequately. Solid tantalums or appropriate
multilayer ceramic capacitors are recommended for
operation below 25°C.
At lower values of output current, less output capacitance
is required for output stability. The capacitor can be reduced
to 0.33 mF for currents less than 10 mA, or 0.1 mF for currents
below 1.0 mA. Using the 8 pin versions at voltages less than
5.0 V operates the error amplifier at lower values of gain, so
that more output capacitance is needed for stability. For the
worst case operating condition of a 100 mA load at 1.23 V
output (output Pin 1 connected to the feedback Pin 7)
a minimum capacitance of 3.3 mF is recommended.
The LP2950 will remain stable and in regulation when
operated with no output load. When setting the output
voltage of the LP2951 with external resistors, the resistance
values should be chosen to draw a minimum of 1.0 mA.
A bypass capacitor is recommended across the
LP2950/LP2951 input to ground if more than 4 inches of
wire connects the input to either a battery or power supply
filter capacitor.
Input capacitance at the LP2951 Feedback Pin 7 can
create a pole, causing instability if high value external
resistors are used to set the output voltage. Adding a 100 pF
capacitor between the Output Pin 1 and the Feedback Pin 7
and increasing the output filter capacitor to at least 3.3 mF
will stabilize the feedback loop.
Error Detection Comparator
The comparator switches to a positive logic low whenever
the LP2951 output voltage falls more than approximately
5.0% out of regulation. This value is the comparators
designed−in of fset voltage of 60 mV divided by the 1.235 V
internal reference. As shown in the representative block
diagram. This trip level remains 5.0% below normal
regardless of the value of regulated output voltage. For
example, the error flag trip level is 4.75 V for a normal 5.0 V
regulated output, or 9.50 V for a 10 V output voltage.
Figure 2 is a timing diagram which shows the ERROR
signal and the regulated output voltage as the input voltage
to the LP2951 is ramped up and down. The ERROR signal
becomes valid (low) at about 1.3 V input. It goes high when
the input reaches about 5.0 V (Vout exceeds about 4.75 V).
Since the LP2951’s dropout voltage is dependent upon the
load current (refer to the curve in the Typical Performance
Characteristics), the input voltage trip point will vary with
load current. The output voltage trip point does not vary
with load.
The error comparator output is an open collector which
requires an external pullup resistor. This resistor may be
returned to the output or some other voltage within the
system. The resistance value should be chosen to be
consistent with the 400 mA sink capability of the error
comparator. A value between 100 kW and 1.0 MW is
suggested. No pullup resistance is required if this output is
unused.
When operated in the power down mode (Vin = 0 V),
the error comparator output will go high if it has been pulled
up to an external supply (the output transistor is in high
impedance state). To avoid this invalid response, the error
comparator output should be pulled up to Vout (see
Figure 18).
Figure 18. ERROR Output Timing
5.0 V
4.75 V 4.70 V
4.75 V + Vdropout 4.70 V + Vdropout
1.3 V 1.3 V
Not
Valid Pullup
to Vout
Pullup
to Ext
Output
Voltage
ERROR
Input
Voltage
Not
Valid
Programming the Output Voltage (LP2951)
The LP2951CX may be pin−strapped for the nominal
fixed output voltage using its internal voltage divider by
tying Pin 1 (output) to Pin 2 (sense) and Pin 7 (feedback) to
Pin 6 (5.0 V tap). Alternatively, it may be programmed for
any output voltage between its 1.235 reference voltage and
its 30 V maximum rating. An external pair of resistors is
required, as shown in Figure 19.
LP2950, LP2951, NCV2951
www.onsemi.com
10
Figure 19. Adjustable Regulator
Error
Output
Shutdown
Input
Vin
Vout
1.23 to 30
V
3.3 mF
0.01 mF
NC
NC
R2
R1
100 k
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
The complete equation for the output voltage is:
Vout +Vref (1)R1ńR2))IFB R1
where Vref is the nominal 1.235 V reference voltage and IFB
is the feedback pin bias current, nominally − 20 nA. The
minimum recommended load current of 1.0 mA forces an
upper limit of 1.2 MW on the value of R2, if the regulator
must work with no load. IFB will produce a 2% typical error
in Vout which may be eliminated at room temperature by
adjusting R1. For better accuracy, choosing R2 = 100 k
reduces this error to 0.17% while increasing the resistor
program current to 12 mA. Since the LP2951 typically draws
75 mA at no load with Pin 2 open circuited, the extra 12 mA
of current drawn is often a worthwhile tradeoff for
eliminating the need to set output voltage in test.
Output Noise
In many applications it is desirable to reduce the noise
present at the output. Reducing the regulator bandwidth by
increasing the size of the output capacitor is the only method
for reducing noise on the 3 lead LP2950. However,
increasing the capacitor from 1.0 mF to 220 mF only
decreases the noise from 430 mV to 160 mVrms for a 100 kHz
bandwidth at the 5.0 V output.
Noise can be reduced fourfold by a bypass capacitor
across R1, since it reduces the high frequency gain from 4
to unity. Pick
CBypass [1
2pR1 x 200 Hz
or about 0.01 mF. When doing this, the output capacitor must
be increased to 3.3 mF to maintain stability. These changes
reduce the output noise from 430 mV to 126 mVrms for a
100 kHz bandwidth at 5.0 V output. With bypass capacitor
added, noise no longer scales with output voltage so that
improvements are more dramatic at higher output voltages.
Figure 20. 1.0 A Regulator with 1.2 V Dropout
0.01 mF
10 k MTB23P06E
1.0 mF
Unregulated
Input
Error
Output
Shutdown
Input
Vout
5.0 V ±1.0%
0 to 1.0 A
220 mF
2.0 k
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
0.002 mF
1.0 M
LP2951CN
LP2950, LP2951, NCV2951
www.onsemi.com
11
TYPICAL APPLICATIONS
Figure 21. Lithium Ion Battery Cell Charger
1N4001
GND
4.2 V ±0.025 V
NC
NC
50 k
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
0.1 mF
NC
LP2951CN
2.2 mF
330 pF
806 k
1.0%
2.0 M
1.0%
Lithium Ion
Rechargeable
Cell
Unregulated Input
6.0 to 10 Vdc
Figure 22. Low Drift Current Sink
Error
Output
Shutdown
Input
+V = 2.0 to 30 V
1.0 mF
R
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
0.1 mF
Load IL = 1.23/R
IL
Figure 23. Latch Off When Error Flag Occurs
Reset
+Vin
Vout
1.0 mF
NC
NC
R2
R1
470 k
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
470 k
Error flag occurs when Vin is too
low to maintain Vout, or if Vout is re-
duced by excessive load current.
Normally
Closed
2N3906
Figure 24. 5.0 V Regulator with 2.5 V Sleep Function
*Sleep
Input
+Vin
Vout
3.3 mF
NC
NC
100 k
100 k
470 k
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN 200 k
100 pF
2N3906
47 k
CMOS
Gate
Error
Output
Shutdown
Input
LP2951CN
LP2950, LP2951, NCV2951
www.onsemi.com
12
330 k
Figure 25. Regulator with Early Warning and Auxiliary Output
+Vin
Memory
V+
1.0 mF20
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
#1
1.0 mF
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
#2
NC
Reset
VDD
mP
Early Warning All diodes are 1N4148.
Early Warning flag on low input voltage.
Main output latches off at lower input voltages.
Battery backup on auxiliary output.
Operation: Regulator #1’s Vout is programmed one
diode drop above 5.0 V. Its error flag becomes active
when Vin < 5.7 V. When Vin drops below 5.3 V, the
error flag of regulator #2 becomes active and via Q1
latches the main output “off”. When Vin again exceeds
5.7 V, regulator #1 is back in regulation and the early
warning signal rises, unlatching regulator #2 via D3.
D4
2.7 M
Q1
2N3906
D2
D1
D3
27 k
3.6 V
NiCad
Main
Output
Figure 26. 2.0 A Low Dropout Regulator
+Vin
Vout @ 2.0 A
100 mF
NC
NC
R2
R1
470
5
3
Error
SD
GND FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
MJE2955
4.7 M
Error
Flag
Vout = 1.25V (1.0 + R1/R2)
For 5.0 V output, use internal resistors. Wire Pin 6 to 7,
and wire Pin 2 to +Vout Bus.
20 k
47
4.7 mF
Tant
0.05
680
0.033 mF
2N3906
10 k
Current Limit
Section
220
1000 mF
.33 mF
.01 mF
2N3906
LP2950, LP2951, NCV2951
www.onsemi.com
13
Figure 27. Open Circuit Detector for 4.0 to 20 mA Current Loop
5
3
Error
SD
Gnd FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
NC
Output*
0.1 mF
NC
NC
NC
1N457
1N457 360
1N457
1N4001
24
+ 5.0 V
4.7 k
15
20 mA
4
* High for
IL < 3.5 mA
Figure 28. Low Battery Disconnect
2N3906
5
3
Error
SD
Gnd FB
47
6
VO T
SNS 2
Vout
Vin
8
1
LP2951CN
NC
1.0 mF
NC
2
3
1
20
Main V+
Memory V+
6.0 V Lead-Acid
Battery
NiCad Backup
Battery
100 k
31.6 k
MC34164P−5
NC
R , THERMAL RESISTANCE
JAθ
JUNCTION‐TO‐AIR ( C/W)°
40
50
60
70
80
90
100
0
0.4
0.8
1.2
1.6
2.0
2.4
010203025155.0
L, LENGTH OF COPPER (mm)
PD(max) for TA = 50°C
Minimum
Size Pad
PD
L
L
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
, MAXIMUM POWER DISSIPATION (W)
Free Air
Mounted
Vertically
RqJA
2.0 oz. Copper
Figure 29. DPAK Thermal Resistance and Maximum
Power Dissipation versus PCB Copper Length
LP2950, LP2951, NCV2951
www.onsemi.com
14
ORDERING INFORMATION (LP2950)
Part Number Output Voltage
(Volts) Tolerance (%) Package Shipping
LP2950CZ−3.0G 3.0 1.0 TO−92
(Pb−Free) 2000 Units / Bag
LP2950CZ−3.0RAG 3.0 1.0 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950ACZ−3.0G 3.0 0.5 TO−92
(Pb−Free) 2000 Units / Bag
LP2950ACZ−3.0RAG 3.0 0.5 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950CZ−3.3G 3.3 1.0 TO−92
(Pb−Free) 2000 Units / Bag
LP2950CZ−3.3RAG 3.3 1.0 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950ACZ−3.3G 3.3 0.5 TO−92
(Pb−Free) 2000 Units / Bag
LP2950ACZ−3.3RAG 3.3 0.5 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950CZ−5.0G 5.0 1.0 TO−92
(Pb−Free) 2000 Units / Bag
LP2950CZ−5.0RAG 5.0 1.0 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950CZ−5.0RPG 5.0 1.0 TO−92
(Pb−Free) 2000 Units / Ammo Pack
LP2950ACZ−5.0G 5.0 0.5 TO−92
(Pb−Free) 2000 Units / Bag
LP2950ACZ−5.0RAG 5.0 0.5 TO−92
(Pb−Free) 2000 Units / Tape & Reel
LP2950CDT−3.0G 3.0 1.0 DPAK
(Pb−Free) 75 Units / Rail
LP2950CDT−3.0RKG 3.0 1.0 DPAK
(Pb−Free) 2500 Units / Tape & Reel
LP2950ACDT−3.0G 3.0 0.5 DPAK
(Pb−Free) 75 Units / Rail
LP2950ACDT−3RKG 3.0 0.5 DPAK
(Pb−Free) 2500 Units / Tape & Reel
LP2950CDT−3.3G 3.3 1.0 DPAK
(Pb−Free) 75 Units / Rail
LP2950CDT−3.3RKG 3.3 1.0 DPAK
(Pb−Free) 2500 Units / Tape & Reel
LP2950ACDT−3.3RG 3.3 0.5 DPAK
(Pb−Free) 2500 Units / Tape & Reel
LP2950CDT−5.0G 5.0 1.0 DPAK
(Pb−Free) 75 Units / Rail
LP2950CDT−5.0RKG 5.0 1.0 DPAK
(Pb−Free) 2500 Units / Tape & Reel
LP2950ACDT−5.0G 5.0 0.5 DPAK
(Pb−Free) 75 Units / Rail
LP2950ACDT−5RKG 5.0 0.5 DPAK
(Pb−Free) 2500 Units / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
LP2950, LP2951, NCV2951
www.onsemi.com
15
ORDERING INFORMATION (LP2951)
Part Number Output Voltage
(Volts) Tolerance (%) Package Shipping
LP2951CD−3.0G 3.0 1.0 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951CD−3.0R2G 3.0 1.0 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951ACD−3.0G 3.0 0.5 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951ACD−3.0R2G 3.0 0.5 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951CD−3.3G 3.3 1.0 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951CD−3.3R2G 3.3 1.0 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951ACD−3.3G 3.3 0.5 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951ACD−3.3R2G 3.3 0.5 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951CDG 5.0 or Adj. 1.0 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951CDR2G 5.0 or Adj. 1.0 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951ACDG 5.0 or Adj. 0.5 SOIC−8
(Pb−Free) 98 Units / Rail
LP2951ACDR2G 5.0 or Adj. 0.5 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
LP2951CDM−3.0R2G 3.0 1.0 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951ACDM−3.0RG 3.0 0.5 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951CDM−3.3R2G 3.3 1.0 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951ACDM−3.3RG 3.3 0.5 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951CDMR2G 5.0 or Adj. 1.0 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951ACDMR2G 5.0 or Adj. 0.5 Micro8
(Pb−Free) 4000 Units / Tape & Reel
LP2951ACN−3.0G 3.0 0.5 PDIP−8
(Pb−Free) 50 Units / Rail
LP2951CN−3.3G 3.3 1.0 PDIP−8
(Pb−Free) 50 Units / Rail
LP2951ACN−3.3G 3.3 0.5 PDIP−8
(Pb−Free) 50 Units / Rail
LP2951CNG 5.0 or Adj. 1.0 PDIP−8
(Pb−Free) 50 Units / Rail
LP2951ACNG 5.0 or Adj. 0.5 PDIP−8
(Pb−Free) 50 Units / Rail
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
LP2950, LP2951, NCV2951
www.onsemi.com
16
ORDERING INFORMATION (NCV2951)
Part Number Output Voltage
(Volts) Tolerance (%) Package Shipping
NCV2951ACD3.3R2G* 3.3 0.5 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
NCV2951ACDR2G* 5.0 or Adj. 0.5 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
NCV2951CDR2G* 5.0 or Adj. 1.0 SOIC−8
(Pb−Free) 2500 Units / Tape & Reel
NCV2951ACDMR2G* 5.0 or Adj. 0.5 Micro8
(Pb−Free) 4000 Units / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
LP2950, LP2951, NCV2951
www.onsemi.com
17
xx = 3.0, 3.3, or 5.0
y = 3 or 5
yy = 30, 33, or 50
z = A or C
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G = Pb−Free Package
G= Pb−Free Package
(Note: Microdot may be in either location)
MARKING DIAGRAMS
2950
CZ−xx
ALYWG
G
TO−92
CASE 029
*
*This marking diagram also applies to NCV2951.
*
50−yG
ALYWW 50A−yG
ALYWW
50−yyG
ALYWW
DPAK
CASE 369C
50AyyG
ALYWW
SOIC−8
CASE 751
Micro8
CASE 846A
51CN
AWL
YYWWG
PDIP−8
CASE 626
1
8
51z
ALYW
G
1
851z−33
ALYW
G
1
851z−3
ALYW
G
1
8
PAyy
AYWG
G
1
8
P−yy
AYWG
G
1
8
2950A
CZ−xx
ALYWG
G
51ACN
AWL
YYWWG
1
8
51CN−xx
AWL
YYWWG
1
8
51ACN−xx
AWL
YYWWG
1
8
LP2950, LP2951, NCV2951
www.onsemi.com
18
PACKAGE DIMENSIONS
TO−226AA/TO−92
Z SUFFIX
CASE 29−11
ISSUE AM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
R
A
P
J
L
B
K
G
H
SECTION X−X
C
V
D
N
N
XX
SEATING
PLANE DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.175 0.205 4.45 5.20
B0.170 0.210 4.32 5.33
C0.125 0.165 3.18 4.19
D0.016 0.021 0.407 0.533
G0.045 0.055 1.15 1.39
H0.095 0.105 2.42 2.66
J0.015 0.020 0.39 0.50
K0.500 --- 12.70 ---
L0.250 --- 6.35 ---
N0.080 0.105 2.04 2.66
P--- 0.100 --- 2.54
R0.115 --- 2.93 ---
V0.135 --- 3.43 ---
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. CONTOUR OF PACKAGE BEYOND
DIMENSION R IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P
AND BEYOND DIMENSION K MINIMUM.
RA
P
J
B
K
G
SECTION X−X
C
V
D
N
XX
SEATING
PLANE DIM MIN MAX
MILLIMETERS
A4.45 5.20
B4.32 5.33
C3.18 4.19
D0.40 0.54
G2.40 2.80
J0.39 0.50
K12.70 ---
N2.04 2.66
P1.50 4.00
R2.93 ---
V3.43 ---
1
T
STRAIGHT LEAD
BULK PACK
BENT LEAD
TAPE & REEL
AMMO PACK
LP2950, LP2951, NCV2951
www.onsemi.com
19
PACKAGE DIMENSIONS
DPAK (SINGLE GAUGE)
CASE 369C
ISSUE F
b
D
E
b3
L3
L4b2
M
0.005 (0.13) C
c2
A
c
C
Z
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
D0.235 0.245 5.97 6.22
E0.250 0.265 6.35 6.73
A0.086 0.094 2.18 2.38
b0.025 0.035 0.63 0.89
c2 0.018 0.024 0.46 0.61
b2 0.028 0.045 0.72 1.14
c0.018 0.024 0.46 0.61
e0.090 BSC 2.29 BSC
b3 0.180 0.215 4.57 5.46
L4 −− 0.040 −− 1.01
L0.055 0.070 1.40 1.78
L3 0.035 0.050 0.89 1.27
Z0.155 −− 3.93 −−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. THERMAL PAD CONTOUR OPTIONAL WITHIN DI-
MENSIONS b3, L3 and Z.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL
NOT EXCEED 0.006 INCHES PER SIDE.
5. DIMENSIONS D AND E ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY.
6. DATUMS A AND B ARE DETERMINED AT DATUM
PLANE H.
7. OPTIONAL MOLD FEATURE.
12 3
4
5.80
0.228
2.58
0.102
1.60
0.063
6.20
0.244
3.00
0.118
6.17
0.243
ǒmm
inchesǓ
SCALE 3:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
H0.370 0.410 9.40 10.41
A1 0.000 0.005 0.00 0.13
L1 0.114 REF 2.90 REF
L2 0.020 BSC 0.51 BSC
A1
H
DET AIL A
SEATING
PLANE
A
B
C
L1
L
H
L2 GAUGE
PLANE
DETAIL A
ROTATED 90 CW5
eBOTTOM VIEW
Z
BOTTOM VIEW
SIDE VIEW
TOP VIEW
ALTERNATE
CONSTRUCTIONS
NOTE 7
Z
LP2950, LP2951, NCV2951
www.onsemi.com
20
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
SEATING
PLANE
1
4
58
N
J
X 45_
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
BS
D
H
C
0.10 (0.004)
DIM
AMIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
−X−
−Y−
G
M
Y
M
0.25 (0.010)
−Z−
Y
M
0.25 (0.010) ZSXS
M
____
1.52
0.060
7.0
0.275
0.6
0.024 1.270
0.050
4.0
0.155
ǒmm
inchesǓ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
LP2950, LP2951, NCV2951
www.onsemi.com
21
PACKAGE DIMENSIONS
PDIP−8
CASE 626−05
ISSUE P
SCALE 1:1
14
58
b2
NOTE 8
D
b
L
A1
A
eB
E
A
TOP VIEW
C
SEATING
PLANE
0.010 CA
SIDE VIEW
END VIEW
END VIEW
WITH LEADS CONSTRAINED
DIM MIN MAX
INCHES
A−−−− 0.210
A1 0.015 −−−−
b0.014 0.022
C0.008 0.014
D0.355 0.400
D1 0.005 −−−−
e0.100 BSC
E0.300 0.325
M−−−− 10
−− 5.33
0.38 −−
0.35 0.56
0.20 0.36
9.02 10.16
0.13 −−
2.54 BSC
7.62 8.26
−−− 10
MIN MAX
MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACK-
AGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3.
4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH
OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE
NOT TO EXCEED 0.10 INCH.
5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM
PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR
TO DATUM C.
6. DIMENSION eB IS MEASURED AT THE LEAD TIPS WITH THE
LEADS UNCONSTRAINED.
7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE
LEADS, WHERE THE LEADS EXIT THE BODY.
8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE
CORNERS).
E1 0.240 0.280 6.10 7.11
b2
eB −−−− 0.430 −− 10.92
0.060 TYP 1.52 TYP
E1
M
8X
c
D1
B
A2 0.115 0.195 2.92 4.95
L0.115 0.150 2.92 3.81
°°
H
NOTE 5
e
e/2 A2
NOTE 3
MBMNOTE 6
M
LP2950, LP2951, NCV2951
www.onsemi.com
22
PACKAGE DIMENSIONS
Micro8t
CASE 846A−02
ISSUE J
S
B
M
0.08 (0.003) A S
T
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
b
e
PIN 1 ID
8 PL
0.038 (0.0015)
−T− SEATING
PLANE
A
A1 cL
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
DIM
AMIN NOM MAX MIN
MILLIMETERS
−− 1.10 −−
INCHES
A1 0.05 0.08 0.15 0.002
b0.25 0.33 0.40 0.010
c0.13 0.18 0.23 0.005
D2.90 3.00 3.10 0.114
E2.90 3.00 3.10 0.114
e0.65 BSC
L0.40 0.55 0.70 0.016
−− 0.043
0.003 0.006
0.013 0.016
0.007 0.009
0.118 0.122
0.118 0.122
0.026 BSC
0.021 0.028
NOM MAX
4.75 4.90 5.05 0.187 0.193 0.199
HE
HE
DD
E
8X 0.48
0.65
PITCH
5.25
8X
0.80
DIMENSION: MILLIMETERS
RECOMMENDED
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage
may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer
is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of
any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and
do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized
for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices
intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and
hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was
negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright
laws and is not for resale in any manner.
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
LP2950/D
Micro8 is a trademark of International Rectifier.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative