1N5388B-AP - Micro Commercial Components Corp.

1N5338B

THRU

1N5388B

5 Watt

Zener Diode

5.1 to 200 Volts

Features

xZener Voltage From 5.1V to 200V

x Operating Temperature: -55qC to +150qC

x Storage Temperature: -55qC to +150qC

x 5 Watt DC Power Dissipation

x Maximum Forward Voltage @ 1A: 1.2 Volts

x

Power Derating: 67 mW/к Above 75к

Mechanical Data

Case: JEDEC DO-15.

Terminals: Solder plated , solderable per MIL-STD-750,

Method 2026.

Standard Packaging: 52mm tape

DO-15

Cathode

Mark

omponents

20736 Marilla Street Chatsworth



 !"#

$%    !"#

MCC

Revision: D 2013/05/29

Micro Commercial Components

DIMENSIONS

INCHES MM

DIM MIN MAX MIN MAX NOTE

A .230 .300 5.80 7.60

B .104 .140 2.60 3.60

C .026 .034 .70 .90

D 1.000 --- 25.40 ---

• Marking : Cathode band and type number

www.mccsemi.com

1 of 6

x Maximum thermal resistence: 15oC/W from junction to lead

Maximum Ratings:

• Lead Free Finish/RoHS Compliant (Note1) ("P"Suffix designates

Compliant. See ordering information)

Note: 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7.

• Epoxy meets UL 94 V-0 flammability rating

• Moisture Sensitivity Level 1

• Halogen free available upon request by adding suffix "-HF"

1N53

RU 1N

88B

ELECTRICAL CHARACTERISTICS

(

TA=25 unless otherwise noted, VF=1.2 Max

IF=

ll t

)

NOTE:

1. TOLERANCE AND VOLTAGE DESIGNATION - The JEDEC type numbers shown indicate a tolerance of+/-10% with

guaranteed limits on only Vz, IR,Ir, and VF

as shown in the electrical characteristics table. Units with guaranteed limits

on all seven parameters are indicated by suffix “B” for+/-5% tolerance.

2. ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT &Z

ZK) - Test conditions for Zener voltage and impedance are as

follows; Iz is applied 40+/-10 ms prior to reading. Mounting contacts are located from the inside edge of mounting

clips to the body of the diode(Ta=25oC)

Revision: D 2013/05/29

www.mccsemi.com

2 of 6

Micro Commercial Components

REGULATOR

VOLTAGE

TEST

CURRENT

MAXIMUM

DYNAMIC

IMPEDANCE

ZZT

MAXIMUM

REVERSE

CURRENT

TEST

VOLTAGE

MAXIMUM

REGULATOR

CURRENT

IZM

MAXIMUM

DYNAMIC

KNEE

IMPEDANCE

ZZK@1.0mA

MAXIMUM

SURGE

CURRENT

IZSM

MAXIMUM

VOLTAGE

REGULATION

VOLTS mA OHMS A VOLTS mA OHMS A VOLTS

1N5338B 5.1 240 1.5 1 1 930 400 14.4 0.39

1N5339B 5.6 220 1 1 2 865 400 13.4 0.25

1N5340B 6 200 1 1 3 790 300 12.7 0.19

1N5341B 6.2 200 1 1 3 765 200 12.4 0.1

1N5342B 6.8 175 1 10 5.2 700 200 11.5 0.15

1N5343B7.51751.5105.763020010.7

0.15



1N5344B 8.2 150 1.5 10 6.2 580 200 10 0.2

1N5345B 8.7 150 2 10 6.6 545 200 9.5 0.2

1N5346B 9.1 150 2 7.5 6.9 520 150 9.2 0.22

1N5347B 10 125 2 5 7.6 475 125 8.6 0.22

1N5348B 11 125 2.5 5 8.4 430 125 8 0.25

1N5349B 12 100 2.5 2 9.1 395 125 7.5 0.25

1N5350B 13 100 2.5 1 9.9 365 100 7 0.25

1N5351B 14 100 2.5 1 10.6 340 75 6.7 0.25

1N5352B 15 75 2.5 1 11.5 315 75 6.3 0.25

1N5353B 16 75 2.5 1 12.2 295 75 6 0.3

1N5354B 17 70 2.5 0.5 12.9 280 75 5.8 0.35

1N5355B 18 65 2.5 0.5 13.7 264 75 5.5 0.4

1N5356B 19 65 3 0.5 14.4 250 75 5.3 0.4

1N5357B 20 65 3 0.5 15.2 237 75 5.1 0.4

1N5358B 22 50 3.5 0.5 16.7 216 75 4.7 0.45

1N5359B 24 50 3.5 0.5 18.2 198 100 4.4 0.55

1N5360B 25 50 4 0.5 19 190 110 4.3 0.55

1N5361B 27 50 5 0.5 20.6 176 120 4.1 0.6

1N5362B 28 50 6 0.5 21.2 170 130 3.9 0.6

1N5363B 30 40 8 0.5 22.8 158 140 3.7 0.6

1N5364B 33 40 10 0.5 25.1 144 150 3.5 0.6

1N5365B 36 30 11 0.5 27.4 132 160 3.3 0.65

1N5366B 39 30 14 0.5 29.7 122 170 3.1 0.65

1N5367B 43 30 20 0.5 32.7 110 190 2.8 0.7

1N5368B 47 25 25 0.5 35.8 100 210 2.7 0.8

1N5369B 51 25 27 0.5 38.8 93 230 2.5 0.9

1N5370B 56 20 35 0.5 42.6 86 280 2.3 1

1N5371B 60 20 40 0.5 45.5 79 350 2.2 1.2

1N5372B 62 20 42 0.5 47.1 76 400 2.1 1.35

1N5373B 68 20 44 0.5 51.7 70 500 2 1.5

1N5374B 75 20 45 0.5 56 63 620 1.9 1.6

1N5375B 82 15 65 0.5 62.2 58 720 1.8 1.8

1N5376B 87 15 75 0.5 66 54.5 760 1.7 2

1N5377B 91 15 75 0.5 69.2 52.5 760 1.6 2.2

1N5378B 100 12 90 0.5 76 47.5 800 1.5 2.3

1N5379B 110 12 125 0.5 83.6 43 1000 1.4 2.5

1N5380B 120 10 170 0.5 91.2 39.5 1150 1.3 2.5

1N5381B 130 10 190 0.5 98.8 36.6 1250 1.2 2.5

1N5382B 140 8 230 0.5 106 34 1500 1.2 2.5

1N5383B 150 8 330 0.5 114 31.6 1500 1.1 3

1N5384B 160 8 350 0.5 122 29.4 1650 1.1 3

1N5385B 170 8 380 0.5 129 28 1750 1 3

1N5386B 180 5 430 0.5 137 26.4 1750 1 4

1N5387B 190 5 450 0.5 144 25 1850 0.9 5

1N5388B 200 5 480 0.5 152 23.6 1850 0.9 5

MCC PART

NUMBER

3. SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave

current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge

current for a quare wave of any pulse width between 1 ms and 1000ms by plotting the applicable points on

logarithmic paper. Examples of this, using the 6.8v , is shown in Figure 6. Mounting

contact located as specified in Note 3. (TA=25 ).

4. VOLTAGE REGULATION (Vz) - Test conditions for voltage regulation are as follows: Vz measurements are made

at 10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test currents are the

same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement is 40+/- 10 ms.

A=25C ). Mounting contact located as specified in Note2.

5. MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage of a

5% type unit. Therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the

value of 5 watts divided by the actual Vz of the device. TL=75Cat maximum from the device body.

APPLICATION NOTE:

1N53

RU 1N

88B

MCC

Revision: D 2013/05/29

Micro Commercial Components

www.mccsemi.com

3 of 6

Since the actual voltage available from a given Zener

diode is temperature dependent, it is necessary to determine

junction temperature under any set of operating conditions

in order to calculate its value. The following procedure is

recommended:

Lead Temperature, TL, should be determined from:

TL = qLA PD + TA

qLA is the lead‐to‐ambient thermal resistance and PD is the

power dissipation.

Junction Temperature, TJ, may be found from:

TJ = TL + DTJL

DTJL is the increase in junction temperature above the lead

temperature and may be found from Figure 4 for a train of

power pulses or from Figure 1 for dc power.

DTJL = qJL PD

For worst‐case design, using expected limits of IZ, limits

of PD and the extremes of TJ (DTJ) may be estimated.

Changes in voltage, VZ, can then be found from:

DV = qVZ DTJ

qVZ, the Zener voltage temperature coefficient, is found

from Figures 2 and 3.

Under high power‐pulse operation, the Zener voltage will

vary with time and may also be affected significantly by the

zener resistance. For best regulation, keep current

excursions as low as possible.

Data of Figure 4 should not be used to compute surge

capability. Surge limitations are given in Figure 5. They are

lower than would be expected by considering only junction

temperature, as current crowding effects cause temperatures

to be extremely high in small spots resulting in device

degradation should the limits of Figure 5 be exceeded.

RATING AND CHARACTERISTICS CURVES

1N5338B THRU 1N5388B

TEMPERATURE COEFFICIENTS

0 20 40 60 80 100 120 140 160

TL, LEAD TEMPERATURE

300

200

100

0 20 40 60 80 100 120 140 160 180 200 22

RANGE

VZ, ZENER VOLTAGE

IZT

(

VOLTS

)

Fig. 1-POWER TEMPERATURE DERATING CURVE Fig. 2-TEMPERATURE COEFFICIENT-RANGE FOR UNITS

6TO51VOLTS

0 0.2

0.4 0.6 0 .8 1

MOUNT ON 8.0mm

COPPER PADS TO

EACH TERMINAL

L, LEAD LENGTH TO HEAT SINK

(

INCH

)

0.4

0.2

0.1

3 4 6 8 10 20 30 40 60 80 100 200

PW = 1ms*

PW = 8.3ms*

PW = 1000ms*

SINE / SQUARE WAVE PW = 100ms*

NOMINAL VZ

(

)

Fig. 4-TYPICAL THERMAL RESISTANCE Fig. 5-MAXIMUM NON-REPETITIVE SURGE

CURRENT VERSUS NOMINAL ZENER

VOLTAGE (SEE NOTE 3)

PD, MAXIUMU POWER DISSIPATION (WATTS)

JL, JUNCTION-TO -LEAD THERMAL

RESISTANCE (C/W)

IR, PEAK SURGE CURRENT (AMPS)

MCC

Revision: D 2013/05/29

Micro Commercial Components

www.mccsemi.com

4 of 6

θVZ, TEMPERATURE COEFFICIENT

(mV/°C) @ I ZT

θJL (t, D), TRANSIENT THERMAL RESISTANCE

JUNCTION‐TO‐LEAD (°C/W)

0.5

0.2

0.001 0.005 0.01 0.05 0.1 0.5 1 5 10 20 50 100

D = 0.5

D = 0.2

D = 0.1

D = 0.05

D = 0.01

D = 0

NOTE: BELOW 0.1 SECOND, THERMAL

NOTE: RESPONSE CURVE IS APPLICABLE

NOTE: TO ANY LEAD LENGTH (L).

DUTY CYCLE, D = t1/t2

SINGLE PULSE D TJL = qJL(t)PPK

REPETITIVE PULSES D TJL = qJL(t, D)PPK

PPK t1

t, TIME (SECONDS)

Figure 3. Typical Thermal Response

L, Lead Length = 3/8 Inch

RATING AND CHARACTERISTICS CURVES

1N5338B THRU 1N5388B

ZENER VOLTAGE VERSUS ZENER CURRENT

(FIGURES 7,8)

0.5

0.2

0.1

1 10 100 1000

VZ = 6.8V

PLOTTED FROM INFORMATION

GIVEN IN FIGURE 5

1000

100

0.1

12345678910

T=25

TC=25

ZENER VOLTAGE

(

VOLTS

)

Fig. 6-PEAK SURGE CURRENT VERSUS PULSE

WIDTH(SEE NOTE 3)

Fig. 7-ZENER VOLTAGE VERSUS ZENER CURRENT

VZ = 6.8 THRU 10 VOLTS

1000

100

0.1

10 20 30 40 50 60

70 80

T=25

VZ, ZENER VOLTAGE

(

VOLTS

)

Fig. 8-ZENER VOLTAGE VERSUS ZENER CURRENT

VZ = 11 THRU 51 VOLTS

*** Data of Figure 3 should not be used to compute surge capability. Surge limitations are given in Figure 5. They are

lower than would be expected by considering only junction temperature, as current crowding effects cause

temperatures to be extremely high in small spots resulting in device degradation should the limits of Figure. 5 be

exceeded

IZ, ZENER CURRENT (mA)

Revision: D 2013/05/29

Micro Commercial Components

www.mccsemi.com

5 of 6

Ir, PEAK SURGE CURRENT (AMPS)

MCC

Revision: D 2013/05/29

Micro Commercial Components

www.mccsemi.com

6 of 6

Device Packing

Part Number-TP Tape&Reel: 4Kpcs/Reel

Part Number-AP Ammo Packing: 3Kpcs/Ammo Box

Part Number-BP Bulk: 25Kpcs/Carton

Ordering Information :

***IMPORTANT NOTICE***

Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to

make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components

Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it

convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all

risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are

represented on our website, harmless against all damages.

***LIFE SUPPORT***

MCC's products are not authorized for use as critical components in life support devices or systems without the express written

approval of Micro Commercial Components Corporation.

***CUSTOMER AWARENESS***

Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking

strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages

customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on

our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine

parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty

coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global

problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized

distributors.

Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF