OPA OPA342 OPA2342 OPA4342 434 2 OPA 342 OPA 234 2 OPA (R) 342 OPA 434 2 www.ti.com Low-Cost, Low-Power, Rail-to-Rail OPERATIONAL AMPLIFIERS MicroAmplifier TM Series FEATURES DESCRIPTION LOW QUIESCENT CURRENT: 150A typ RAIL-TO-RAIL INPUT RAIL-TO-RAIL OUTPUT (within 1mV) SINGLE SUPPLY CAPABILITY LOW COST MicroSIZE PACKAGE OPTIONS: SOT23-5 MSOP-8 TSSOP-14 BANDWIDTH: 1MHz SLEW RATE: 1V/s THD + NOISE: 0.006% The OPA342 series rail-to-rail CMOS operational amplifiers are designed for low-cost, low-power, miniature applications. They are optimized to operate on a single supply as low as 2.5V with an input commonmode voltage range that extends 300mV beyond the supplies. Rail-to-rail input/output and high-speed operation make them ideal for driving sampling Analog-to-Digital Converters (ADC). They are also well suited for generalpurpose and audio applications and providing I/V conversion at the output of Digital-to-Analog Converters (DAC). Single, dual, and quad versions have identical specs for design flexibility. The OPA342 series offers excellent dynamic response with a quiescent current of only 250A max. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. APPLICATIONS COMMUNICATIONS PCMCIA CARDS DATA ACQUISITION PROCESS CONTROL AUDIO PROCESSING ACTIVE FILTERS TEST EQUIPMENT CONSUMER ELECTRONICS PACKAGE SINGLE OPA342 SOT23-5 QUAD OPA4342 MSOP-8 SO-8 DUAL OPA2342 TSSOP-14 SO-14 DIP-14 SPICE MODEL available at www.burr-brown.com. Copyright (c) 2000, Texas Instruments Incorporated SBOS106A Printed in U.S.A. August, 2000 SPECIFICATIONS: VS = 2.7V to 5.5V At TA = +25C, RL = 10k connected to VS /2 and VOUT = VS /2, unless otherwise noted. Boldface limits apply over the temperature range, TA = -40C to +85C. OPA342NA, UA OPA2342EA, UA OPA4342EA, UA, PA PARAMETER OFFSET VOLTAGE Input Offset Voltage TA = -40C to +85C vs Temperature vs Power Supply TA = -40C to +85C Channel Separation, dc f = 1kHz CONDITION VOS dVOS/dT PSRR VCM = VS /2 VS = 2.7V to 5.5V, VCM < (V+) -1.8V VS = 2.7V to 5.5V, VCM < (V+) -1.8V 6 6 mV mV V/C V/V V/V V/V dB 200 250 8 30 0.5 VCM CMRR CMRR CMRR AOL FREQUENCY RESPONSE Gain-Bandwidth Product GBW Slew Rate SR Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise, f = 1kHz THD+N OUTPUT Voltage Output Swing from Rail(2) TA = -40C to +85C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT23-5 Surface Mount MSOP-8 Surface Mount SO-8 Surface Mount TSSOP-14 Surface Mount SO-14 Surface Mount DIP-14 1 1 3 30 en in TA = -40C to +85C POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = -40C to +85C UNITS IOS VS = +5.5V, -0.3V < VCM < (V+) - 1.8 VS = +5.5V, -0.3V < VCM < (V+) - 1.8 VS = +5.5V, -0.3V < VCM < 5.8V VS = +5.5V, -0.3V < VCM < 5.8V VS = +2.7V, -0.3V < VCM < 3V VS = +2.7V, -0.3V < VCM < 3V -0.3 76 74 66 64 62 60 INPUT IMPEDANCE Differential Common-Mode TA = -40C to +85C Short-Circuit Current Capacitive Load Drive MAX 0.2 See Typical Curve 0.2 IB NOISE Input Voltage Noise, f = 0.1Hz to 50kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz OPEN-LOOP GAIN Open-Loop Voltage Gain TA = -40C to +85C TYP 0.2 132 INPUT BIAS CURRENT Input Bias Current TA = -40C to +85C Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio TA = -40C to +85C Common-Mode Rejection Ratio TA = -40C to +85C Common-Mode Rejection Ratio TA = -40C to +85C MIN ISC CLOAD RL = 100k, 10mV < VO < (V+) - 10mV RL = 100k, 10mV < VO < (V+) - 10mV RL = 5k, 400mV < VO < (V+) - 400mV RL = 5k, 400mV < VO < (V+) - 400mV CL = 100pF G=1 RL = 100k, AOL 96dB RL = 100k, AOL 104dB RL = 100k, AOL 100dB RL = 5k, AOL 96dB RL = 5k, AOL 90dB Per Channel pA pA pA 10 Vrms nV/Hz fA/Hz (V+) + 0.3 V dB dB dB dB dB dB 88 78 74 1013 || 3 1013 || 6 || pF || pF 124 dB dB dB dB 114 1 1 5 8 2.5 0.006 VS = 5.5V, 2V Step VS = 5.5V, 2V Step VIN * G = VS VS = 5.5V, VO = 3Vp-p(1), G = 1 VS IQ 104 100 96 90 10 MHz V/s s s s % 1 3 mV mV mV mV mV mA 10 10 400 400 20 15 See Typical Curve 2.7 5.5 2.5 to 5.5 150 IO = 0A -40 -55 -65 JA 250 300 V V A A +85 +125 +150 C C C C/W C/W C/W C/W C/W C/W 200 150 150 100 100 100 NOTES: (1) VOUT = 0.25V to 3.25V. (2) Output voltage swings are measured between the output and power-supply rails. 2 OPA342, 2342, 4342 SBOS106A ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage, V+ to V- ................................................................... 7.5V Signal Input Terminals, Voltage(2) ..................... (V-) -0.5V to (V+) +0.5V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. -55C to +125C Storage Temperature ..................................................... -65C to +150C Junction Temperature ...................................................................... 150C Lead Temperature (soldering, 10s) ................................................. 300C ESD Tolerance (Human Body Model) ............................................ 4000V This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only. Functional operation of the device at these conditions, or beyond the specified operating conditions, is not implied. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current-limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER OPA342NA SOT23-5 331 -40C to +85C B42 " " " " OPA342UA " OPA342UA SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA OPA342NA/250 OPA342NA /3K OPA342UA OPA342UA /2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA2342EA /250 OPA2342EA /2K5 OPA2342UA OPA2342UA /2K5 Tape and Reel Tape and Reel Rails Tape and Reel OPA4342EA /250 OPA4342EA /2K5 OPA4342UA OPA4342UA /2K5 OPA4342PA Tape and Reel Tape and Reel Rails Tape and Reel Rails SO-8 182 -40C to +85C " " " " " OPA2342EA MSOP-8 337 -40C to +85C C42 " " " " " OPA2342UA SO-8 182 -40C to +85C OPA2342UA " " " " " OPA4342EA TSSOP-14 357 -40C to +85C OPA4342EA " " " " " OPA4342UA SO-14 235 -40C to +85C OPA4342UA " " " " " OPA4342PA DIP-14 010 -40C to +85C OPA4342PA NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3000 devices per reel). Ordering 3000 pieces of "OPA342NA/3K" will get a single 3000-piece Tape and Reel. PIN CONFIGURATIONS OPA342 Out 1 V- 2 +In 3 5 4 OPA4342 V+ -In Out A 1 -In A 2 A 14 Out D 13 -In D D +In A 3 12 +In D +V 4 11 -V +In B 5 10 +In C SOT23-5 OPA342 OPA2342 NC 1 8 NC Out A 1 -In 2 7 V+ -In A 2 +In 3 6 Out +In A 3 V- 4 5 NC V- 4 A B B C 8 V+ -In B 6 9 -In C 7 Out B Out B 7 8 Out C 6 -In B 5 +In B TSSOP-14, SO-14, DIP-14 SO-8 OPA342, 2342, 4342 SBOS106A SO-8, MSOP-8 3 TYPICAL PERFORMANCE CURVES At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 100 100 30 80 +PSRR Phase 80 60 60 90 40 120 Phase () Gain (dB) 0 Gain 20 Rejection Ratio (dB) 120 0.1 10 1 100 1k 10k 100k 1M 60 40 20 150 0 CMRR -PSRR 10 180 10M 10 100 Channel Separation (dB) Maximum Output Voltage (Vp-p) VS = +5.5V 5 VS = +5V 4 3 VS = +2.7V 2 1 120 100 Dual and quad devices. G = 1, all channels. Quad measured channel A to D or B to C--other combinations yield improved rejection. 80 60 100k 10k 100 1M 100k VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY VN 100 1 10 100 1k 10k Frequency (Hz) 100k 1M 0.1 10M 0.1 THD+N (%) 10 1M 1 Current Noise (fA/Hz) IN 1000 10 10k Frequency (Hz) 100 1 1k Frequency (Hz) 10000 Voltage Noise (nV/Hz) 100k 140 0 4 10k CHANNEL SEPARATION vs FREQUENCY MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 1k Frequency (Hz) Frequency (Hz) 0.010 0.001 20 100 1k 10k 20k Frequency (Hz) OPA342, 2342, 4342 SBOS106A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN, COMMON-MODE REJECTION RATIO, AND POWER SUPPLY REJECTION vs TEMPERATURE INPUT BIAS CURRENT vs TEMPERATURE 140 10000 AOL Input Bias Current (pA) AOL, CMRR, PSRR (dB) 120 100 CMRR 80 PSRR 60 40 20 0 1000 100 10 1 0.1 -75 -50 -25 0 25 50 75 100 125 150 -75 -50 -25 Temperature (C) 0 25 50 75 100 125 Temperature (C) QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE SLEW RATE vs TEMPERATURE 200 40 1.2 175 35 1 30 135 25 +ISC 100 20 -ISC 75 15 50 10 25 5 0 -75 -50 25 0 -25 50 75 100 Slew Rate (V/s) IQ 150 Short-Circuit Current (mA) Quiescent Current (A) -SR 0.8 +SR 0.6 0.4 0.2 0 0 125 -75 -50 -25 0 25 50 75 100 Temperature (C) Temperature (C) INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE 125 160 6 20 V- Supply 2 V+ Supply Quiescent Current (A) Input Bias Current (pA) 4 0 -2 Input voltage -0.3V can cause op amp output to lock up. See text. -4 155 15 -ISC 150 10 IQ 145 5 140 -6 -1 0 1 2 3 4 Common-Mode Voltage (V) OPA342, 2342, 4342 SBOS106A 5 6 Short-Circuit Current (mA) +ISC 0 2 3 4 5 6 Supply Voltage (V) 5 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN vs OUTPUT VOLTAGE SWING OUTPUT VOLTAGE SWING vs OUTPUT CURRENT V+ 120 -40C (V+) - 2 2 85C 25C 25C -40C 1 85C Open-Loop Gain (dB) Output Voltage (V) (V+) - 1 0 RL = 100k 100 RL = 5k 90 80 5 0 10 15 120 20 100 80 60 40 20 Output Current (mA) Output Voltage Swing from Rail (mV) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 24 16 12 8 4 0 18 Typical production distribution of packaged units. 16 Percent of Amplifiers (%) Typical production distribution of packaged units. 20 Percent of Amplifiers (%) 110 14 12 10 8 6 4 2 0 -6 -5.4 -4.8 -4.2 -3.6 -3 -2.4 -1.8 -1.2 -0.6 0 0.6 1.2 1.8 2.4 3 3.6 4.2 4.8 5.4 6 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 0 Offset Voltage (mV) Offset Voltage Drift (V/C) QUIESCENT CURRENT PRODUCTION DISTRIBUTION SETTLING TIME vs CLOSED-LOOP GAIN 400 350 20 300 Settling Time (s) Percent of Amplifiers (%) 24 16 12 8 250 0.01% 200 150 100 0.1% 4 50 0 <250 <225 <200 <175 <150 <125 <100 <75 <50 <25 <0 0 1 10 100 1000 Closed-Loop Gain (V/V) Quiescent Current (A) 6 OPA342, 2342, 4342 SBOS106A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = +5V, and RL = 10k connected to VS/2, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE G = +1, RL = 10k, CL = 100pF SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 50 40 35 G = +1 30 1V/div Small-Signal Overshoot (%) 45 G = +5 25 G = -1 20 15 10 G = -5 5 0 1 10 100 1k 10k 5s/div Load Capacitance (pF) 20mV/div SMALL-SIGNAL STEP RESPONSE G = +1, RL = 10k, CL = 100pF 5s/div OPA342, 2342, 4342 SBOS106A 7 APPLICATIONS INFORMATION OPA342 series op amps are unity gain stable and can operate on a single supply, making them highly versatile and easy to use. Rail-to-rail input and output swing significantly increases dynamic range, especially in low supply applications. Figure 1 shows the input and output waveforms for the OPA342 in unity-gain configuration. Operation is from VS = +5V with a 10k load connected to VS /2. The input is a 5Vp-p sinusoid. Output voltage is approximately 4.997Vp-p. Power supply pins should be by passed with 0.01F ceramic capacitors. G = +1, VS = +5V Input 1V/div 5V 0V Output (inverted on scope) OPERATING VOLTAGE OPA342 series op amps are fully specified and guaranteed from +2.7V to +5.5V. In addition, many specifications apply from -40C to +85C. Parameters that vary significantly with operating voltages or temperature are shown in the Typical Performance Curves. RAIL-TO-RAIL INPUT The input common-mode voltage range of the OPA342 series extends 300mV beyond the supply rails. This is achieved with a complementary input stage--an N-channel input differential pair in parallel with a P-channel differential pair (see Figure 2). The N-channel pair is active for input voltages close to the positive rail, typically (V+) - 1.3V to 300mV above the positive supply, while the P-channel pair is on for inputs from 300mV below the negative supply to approximately (V+) -1.3V. There is a small transition region, typically (V+) - 1.5V to (V+) - 1.1V, in which both pairs are on. This 400mV transition region can vary 300mV with process variation. Thus, the transition region (both stages on) can range from (V+) - 1.8V to (V+) - 1.4V on the low end, up to (V+) - 1.2V to (V+) - 0.8V on the high end. Within the 400mV transition region PSRR, CMRR, offset voltage, offset drift, and THD may be degraded compared to operation outside this region. For more information on designing with rail-to-rail input op amps, see Figure 3 "Design Optimization with Rail-to-Rail Input Op Amps." 5s/div FIGURE 1. Rail-to-Rail Input and Output. V+ Reference Current VIN+ VIN- VBIAS1 Class AB Control Circuitry VO VBIAS2 V- (Ground) FIGURE 2. Simplified Schematic. 8 OPA342, 2342, 4342 SBOS106A DESIGN OPTIMIZATION WITH RAIL-TO-RAIL INPUT OP AMPS With a unity-gain buffer, for example, signals will traverse this transition at approximately 1.3V below V+ supply and may exhibit a small discontinuity at this point. The common-mode voltage of the non-inverting amplifier is equal to the input voltage. If the input signal always remains less than the transition voltage, no discontinuity will be created. The closed-loop gain of this configuration can still produce a rail-to-rail output. Inverting amplifiers have a constant common-mode voltage equal to VB. If this bias voltage is constant, no discontinuity will be created. The bias voltage can generally be chosen to avoid the transition region. Rail-to-rail op amps can be used in virtually any op amp configuration. To achieve optimum performance, however, applications using these special double-input-stage op amps may benefit from consideration of their special behavior. In many applications, operation remains within the common-mode range of only one differential input pair. However some applications exercise the amplifier through the transition region of both differential input stages. Although the two input stages are laser trimmed for excellent matching, a small discontinuity may occur in this transition. Careful selection of the circuit configuration, signal levels and biasing can often avoid this transition region. G = 1 Buffer Non-Inverting Gain V+ Inverting Amplifier V+ VB VO VIN V+ VIN VO VO VIN VB VCM = VIN = VO VCM = VIN VCM = VB FIGURE 3. Design Optimization with Rail-to-Rail Input Op Amps. COMMON-MODE REJECTION The CMRR for the OPA342 is specified in several ways so the best match for a given application may be used. First, the CMRR of the device in the common-mode range below the transition region (VCM < (V+) - 1.8V) is given. This specification is the best indicator of the capability of the device when the application requires use of one of the differential input pairs. Second, the CMRR at VS = 5.5V over the entire common-mode range is specified. Third, the CMRR at VS = 2.7V over the entire common-mode range is provided. These last two values include the variations seen through the transition region. INPUT VOLTAGE BEYOND THE RAILS If the input voltage can go more than 0.3V below the negative power supply rail (single-supply ground), special precautions are required. If the input voltage goes sufficiently negative, the op amp output may lock up in an inoperative state. A Schottky diode clamp circuit will prevent this--see Figure 4. The series resistor prevents excessive current (greater than 10mA) in the Schottky diode and in the internal ESD protection diode, if the input voltage can exceed the positive supply voltage. If the signal source is limited to less than 10mA, the input resistor is not required. RAIL-TO-RAIL OUTPUT A class AB output stage with common-source transistors is used to achieve rail-to-rail output. This output stage is capable of driving 600 loads connected to any potential OPA342, 2342, 4342 SBOS106A between V+ and ground. For light resistive loads (> 50k), the output voltage can typically swing to within 1mV from supply rail. With moderate resistive loads (2k to 50k), the output can swing to within a few tens of milli-volts from the supply rails while maintaining high open-loop gain. See the typical performance curve "Output Voltage Swing vs Output Current." V+ IOVERLOAD 10mA max OPA342 VOUT VIN 1k IN5818 Schottky diode is required only if input voltage can go more than 0.3V below ground. FIGURE 4. Input Current Protection for Voltages Exceeding the Supply Voltage. CAPACITIVE LOAD AND STABILITY The OPA342 in a unity-gain configuration can directly drive up to 250pF pure capacitive load. Increasing the gain enhances the amplifier's ability to drive greater capacitive loads. See the typical performance curve "Small-Signal 9 DRIVING A/D CONVERTERS The OPA342 series op amps are optimized for driving medium-speed sampling ADCs. The OPA342 op amps buffer the ADC's input capacitance and resulting charge injection while providing signal gain. Overshoot vs Capacitive Load." In unity-gain configurations, capacitive load drive can be improved by inserting a small (10 to 20) resistor, RS, in series with the output, as shown in Figure 5. This significantly reduces ringing while maintaining dc performance for purely capacitive loads. However, if there is a resistive load in parallel with the capacitive load, a voltage divider is created, introducing a dc error at the output and slightly reducing the output swing. The error introduced is proportional to the ratio RS /RL, and is generally negligible. Figures 6 shows the OPA342 in a basic noninverting configuration driving the ADS7822. The ADS7822 is a 12-bit, micro-power sampling converter in the MSOP-8 package. When used with the low-power, miniature packages of the OPA342, the combination is ideal for space-limited, lowpower applications. In this configuration, an RC network at the ADC's input can be used to filter charge injection. V+ Figure 7 shows the OPA2342 driving an ADS7822 in a speech bandpass filtered data acquisition system. This small, low-cost solution provides the necessary amplification and signal conditioning to interface directly with an electret microphone. This circuit will operate with VS = +2.7V to +5V with less than 500A quiescent current. RS VOUT OPA342 10 to 20 VIN RL CL FIGURE 5. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive. +5V 0.1F 0.1F 1 VREF 8 V+ DCLOCK 500 +In OPA342 ADS7822 12-Bit A/D 2 VIN DOUT -In CS/SHDN 3 3300pF 7 6 Serial Interface 5 GND 4 VIN = 0V to 5V for 0V to 5V output. NOTE: A/D Input = 0 to VREF RC network filters high frequency noise. FIGURE 6. OPA342 in Noninverting Configuration Driving ADS7822. V+ = +2.7V to 5V Passband 300Hz to 3kHz R9 510k R1 1.5k R2 1M R4 20k C3 33pF C1 1000pF 1/2 OPA2342 Electret Microphone(1) R3 1M R6 100k R7 51k R8 150k VREF 1 8 V+ 7 C2 1000pF 1/2 OPA2342 +IN ADS7822 6 12-Bit A/D 5 2 -IN DCLOCK DOUT CS/SHDN Serial Interface 3 4 NOTE: (1) Electret microphone powered by R1. R5 20k G = 100 GND FIGURE 7. Speech Bandpass Filtered Data Acquisition System. 10 OPA342, 2342, 4342 SBOS106A PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA2342EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2342EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2342EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2342EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR OPA2342UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2342UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2342UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2342UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342NA/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342NA/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342NA/3K ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342NA/3KG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA342UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4342EA/250 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4342EA/250G4 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4342PA ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA4342PAG4 ACTIVE PDIP N 14 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA4342UA ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4342UAG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2342EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2342EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2342UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4342EA/250 TSSOP PW 14 250 180.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2342EA/250 VSSOP DGK OPA2342EA/2K5 VSSOP DGK 8 250 210.0 185.0 35.0 8 2500 367.0 367.0 35.0 OPA2342UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA4342EA/250 TSSOP PW 14 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated