Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 1 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
Technical Data Sheet
1.8mm Round Subminiature Infrared LED
HIR42-21C/TR8
Features
Compatible with infrared and vapor phase reflow solder process.
Low forward voltage
Good spectral matching
to Si photodetector
Pb free
The product itself will remain within RoHS compliant version.
Descriptions
HIR42-21C/TR8 is an infrared emitting diode in miniature SMD
package which is molded in a water clear plastic with spherical
top view lens.
The device is spectrally matched with silicon photodiode and
phototransistor.
Applications
PCB mounted infrared sensor
Infrared emitting for miniature light barrier
Floppy disk drive
Optoelectronic switch
Smoke detector
Device Selection Guide Chip
LED Part No. Material Lens Color
HIR GaAlAs Water clear
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 2 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
121
2Cathode
Anode
1
2
HIR42-21C/TR8
Package Dimensions
Notes: 1.All dimensions are in millimeters
2.Tolerances unless dimensions ±0.1mm
Absolute Maximum Ratings (Ta=25)
Parameter Symbol Rating Units
Continuous Forward Current IF 65 mA
Reverse Voltage VR 5 V
Operating Temperature Topr -25 ~ +85
Storage Temperature Tstg -40 ~ +100
Soldering Temperature Tsol 260
Power Dissipation at(or below)
25Free Air Temperature Pd 130 mW
Notes: *1:Soldering time5 seconds.
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 3 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
HIR42-21C/TR8
Electro-Optical Characteristics (Ta=25)
Parameter Symbol Condition Min. Typ. Max. Units
IF=20mA 2.0 5.0 15
Radiant Intensity Ie IF=100mA
Pulse Width100μs ,Duty1% -- 20 --
mW /sr
Peak Wavelength λp IF=20mA -- 850 -- nm
Spectral
Bandwidth Δλ IF=20mA -- 45 -- nm
IF=20mA -- 1.45 1.65
Forward Voltage VF . IF=100mA
Pulse Width100μs ,Duty1% -- 1.80 2.40 V
Reverse Current IR VR=5V -- -- 10
μA
View Angle 2θ1/2 IF=20mA -- 20 -- deg
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 4 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
790
0
20
40
60
80
100
890
850810 830 870 930910 950
IF=20mA
Ta=25° C
75
-25
800 0
825
850
25 50
875
900
100 0
10
1
10
102
3
104
21345678
0-25 0 4020 60 10080
20
40
60
100
80
120
140
HIR42-21C/TR8
Typical Electro-Optical Characteristics Curves
Fig.1 Forward Current vs. Fig.2 Spectral Distribution
Ambient Temperature
Fig.3 Peak Emission Wavelength Fig.4 Forward Current
Ambient Temperature vs. Forward Voltage
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 5 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
25
1
1.2
1.4
1.6
50 75 100 120
IF=20mA
-20
0.6
0.9
0.7
0.8
1.0
0.20.4 0 0.2 0.4 0.6
50
70
80
60
40
30
-10 02010
25
1
3
50 75 100 120
IF=20mA
5
7
010
10010
110
2310 4
10
100
1000
IF-Forward Current (mA)
Ie-Radiant Intensity(mW/sr)
HIR42-21C/TR8
Typical Electro-Optical Characteristics Curves
Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs.
Forward Current Angular Displacement
Fig.7 Relative Intensity vs. Fig.8 Forward Current vs.
Ambient Temperature(°C) Ambient Temperature(°C)
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 6 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
HIR42-21C/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5 for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 7 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
HIR42-21C/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280 for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and m o re
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 8 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
HIR42-21C/TR8
Reliability Test Item And Condition
The reliability of products shall be satisfied with items listed below.
Confidence level90%
LTPD10%
NO. Item Test Conditions Test Hours/
Cycles
Sample
Sizes
Failure
Judgement
Criteria
Ac/Re
1 REFLOW Soldering TEMP.260℃±5
5secs
6Mins 22pcs 0/1
2 Temperature Cycle H : +100 15mins
5mins
L : -40 15mins
50Cycles 22pcs 0/1
3 Thermal Shock H :+100 5mins
10secs
L :-10 5mins
50Cycles 22pcs 0/1
4 High Temperature
Storage
TEMP.+100 1000hrs 22pcs 0/1
5 Low Temperature
Storage
TEMP.-40 1000hrs 22pcs 0/1
6 DC Operating Life IF=20mA 1000hrs 22pcs 0/1
7 High Temperature/
High Humidity
85 / 85% R.H 1000hrs 22pcs
IRU×2
EeL×0.8
VFU×1.2
UUpper
Specification
Limit
LLower
Specification
Limit
0/1
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 9 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
HIR42-21C/TR8
Package Dimensions
Taping Dimensions
Unit: mm
Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 10 of 10
Device NoDTH-042-024 Prepared date04-25-2006 Prepared byJaine Tsai
RoHS
HIR42-21C/TR8
Packing Quantity Specification
1.1000Pcs/1Volume1Volume/1Bag
2.10Boxes/1Carton
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
HUE: Peak Wavelength
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximu m ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s
consent.
EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http:\\www.everlight.com
HIR42-21C/TR8